Eat 282 GB Contents Safety instructions Page for the electrical installer 52 for the fitted kitchens technician 52/53 Before installation starts General 54 Description of appliance 54 Technical data: — Dimensions 54/55 — Connected load 56 Ventilator performance, 56 Ventilator air outlet 56 Accessories/installation materials 57 Preparing for installation — Preparing the outset .
For the electrical installer Forth kitchen furniture installer 52 Safety instructions Sting the socket directly above the fume extractor hood or above the wall unit has iwo advantages: 1. The plug socket is not visible. 2. You can easily DE-energize the appliance where necessary by unplugging it. For the necessary fixed connection, the fume extractor had may be connected only by an electrical installer registered with the electricity board covering your area.
a8 SIKKIM 9788 — 1 COMBS The safe joint operation of chimney-linked appliances and fume extractor hoods is only guaranteed if space and/or dwelling {spacewalk interaction} are externally ventilated by a suitable supply air opening of around 500—800 cm? and an under pressure thereby avoided when the fume extractor hood Is running. In doubtful cases, please seek the advice and consent of the competent area chimney-swap or the ioctl building authorities.
General Appliance description Technical data The fume extraction hood is supplied as an exhaust air appliance and may be used as a return air appliance through application of an active carbon filter {special accessory). For this purpose, you need the AEG Originate Active Carbon Fitter {see spacial accessories).
Technical data Air outlet 56 Connected load: 381 0/481 D Total load: 200w Fan motor: 186 W Lighting: 11 W (fluorescent lamp} Fan outputs (stages). Fan stages as defined in DIN 43971 infinitely variable full power Exhaust air: 120 m¥/h 560 mh Return air: 100 m7h 430 mth Exhaust sir system 120 mm die. Air outset arranged centrally above Pipe connection of 120 mm dia for exhaust air hoses of 120 mm da, already attached to appliance. =) TOMS S8 — LADS.
o/m GB VAL ) £ & Accessories/Installation materials resews, 4.5x13 {fur mounting furniture door) screws, 5x45 (for wall hooks) (381 D) pigs for above (381 0) air outlet grille {with screw) screws, 4.5x13 {for side mounting 381 D) screws, 4,5x13 (for side mounting 481 D} plastic covers for above hanging rails hooks {for wall mounting} (381 0) scree's, 4.
Position of the air outlet opening Special accessories for exhaust air hoses ‘The dimensions and position ol the air outlet opening can be seen from the following pictures. 1} 18 mm kitchen furniture side-wall thickness. 2) 16 mm kitchen furniture side-wall thickness. # the side-wall thickness is 19 mm. remove the distance washers trim the extractor hood (481 D) and trim the two mounting hooks. For wall box/fume extractor hood connection, it is best 10 use the non-flammable exhaust alr hose under E-No.
G VOUCH 6781 The extractor hood can be used as a re-circulating hood if no air-shaft or outside wall is available. For use as a re-circulating goad il is necessary to il the KLF 50/80 active-charcoal filter, E-No. 510 899 411 for absorbing pooching fumes, The KLF 60/80 active-charcoal filler is supplied as a special accessory {at an extra charge}. Folio these steps for fitting: 1. Remove the metal grease filter and take the grill off. Fido the grips upwards and pull theremin. Take the grill cut. [GES ] 2.
Installation €0 3. He-inert the grease fighter grill. The extractor hood is now ready for use as a re-circulating hood 1o take the active-charcoal filler out, press in the two red lugs and pull ihe active-charcoal filter out of the housing installing the extractor hood In & cabinet (appliance width 560 mm) or between two hanging cupboards {appliance width 600 mm} {with hanging rails) 1 Remove the fume protection plate. 2.
2 i GUTTED 292~ (LAWS 4 27 3. Push the extractor hood over the two hanging hooks and fasten it from underneath with the two sowers {4.5x 13 mm) {appliance width 560 mm). 4. Leo sen the two screws on the wall skirting strip, push the skirting panel as far as it will go against the cupboard back wall, and tighten both screws again o 54-100 Remove the fume protection plate.
2. Fasten ihe wail hooks with the enclosed two 8 mm wall-plugs and 50 45 mrm screws as show in the illustration. 3 Hook the extractor hood into the wall hooks and stadium it exactly to the hanging cupboard using the adjustment screws {compensate for any differences in height or depth). 4. astern the extractor hood above and underneath (ate ally} with two screws each.
MATHEWS 202 — GUIZHOU-1 1081 GE The Walt skirting strip mounted on the appliance already by the manufacturer is additionally fixed to the wall with 2 screws using wall-plugs. (Gt ] You wail need screws and wall-plugs. Fitting the cabinet front to the fume protection plate of the extractor hood. Scimitar method for ali models and aff locations. 1.
Additional fitting work for re-circulating use Hello B4 Go through the same stage of fitting as for extraction use, then also fit the air outlet girl. 1. When tilling in a hanging cupboard an aperture must be provided of 140 x 140 mm in the top of the cupboard. 2. Fasten the air extraction grill on the top side of the hood as show in the illustration. i this has not already been done during the preparatory work, it is essential to insert the active-charcoal filter KLF 60/80 E-No.
SB 1188 G Safety instructions it must be ensured that hobs are always covered so that the appliance is not damaged by excessive heat liberation. Open fireplaces on col-, gas-, and coal-fired cookers must be avoided. During deep-frying over. a cooker/hob, the appliance used for esp-frying must also be supervised during operation. The oil contained in the deep-frying appliance may spontaneously ignite through overheating. It contaminated oil is used, spontaneous ignition may occur even more readily.
Description of appliance Operating Deandre after-running offal Metal filter{s} Hand-washing Dish washing machine Starting up My push-switches are arranged on the right-hand side. The symbols have the following meanings: = Lighting on ;——fl = of = Full power setting The fan can be regulated by pushing the slide switch. With my cabinet front you can switch the fan on and off while the fan MO IS Funding. Tre same also applies to my work-place sighting.
WKE? 9789 — WORRY 2182 GB “The active carbon filter must be changed not irate then after 1 your. The active carbon filter cannot be washed or regenerated. Good deodorization is conditional upon a suitable active carbon volume (depending on the air capacity ot your fume extractor hood) and specific arrangement of the active carbon filter in your fume extractor hood. This combinations ensures a positive return air supply in contrast fo exhaust air operation.
Active charcoal filter 2 Glean my infernal housing only‘ with warm washing-up water ~ do not use any harsh cleaners, brushes, or abrasives. 3 Adler canning, put the real grease filter back in position: 4. Screw the fuse back in or replace the fuse in the main fused ox. To take out and replace the KLF 80/80 active-charcoal filter, E-No. 610 838 411, proceed as follows: In.order to avoid unintentionally switching on, screw my fuse out its holder or take my ruse out of your main fuse-box. 1.
a8 ekaa2152 4. Fit the new active-charcoal filter first on the lamp side of the extractor hood (1} by pressing in the two red lugs (2) and clip the filter upwards into the extractor hood. e 5 Screw the fuse back in or replace the fuse in the main fuse box. 5. Re-insert meta grease filter grill, ‘The extractor hood is now once again ready for use as a re-circulating hood.
Replacing fluorescent damp You narc change the fluorescent lamp yourself. Turn the current to the appliance off before changing the lamps! 1. Open e cover of the lighting by depressing the locking shade and folding the cover out downwards 2 Suit my old lamp out of the bolder and replace it with a new oni CAUTION: Only ever insert fluorescent lamps with a maximum of 11 W into the holders! 3.
E w00t 948 7 uncanny Important! To clean the fume extractor hood, DE-energize the appliance (e.g. pull out the mains plug). Never introduce sharp abject into the protective grille of the motor Clean the outer parts with a mild washing-up liquid solution. Never use abrasive cleaners, brushes, or scouring agents. Clean the control panel screen and fat filter grille only with a damp cloth and mild washing-up liquid solution. It is important to observe the filter change or cleaning intervals.