32213 32253 32413 G Gas Fueled Built-In Hot Plate Instructions and advice for the use, installation and maintenance
INSTRUCTIONS AND ADVICE FOR THE USE, INSTALLATION AND MAINTENANCE GAS FUELED BUILT-IN HOT PLATE Dear Customer, Thank you for having purchased one of our products. W are certain that this new, modern, functional and practical appliance, bully with the very highest quality materials, will meet your requirements in the best possible way. This appliance is easy to use. it is, however, important to thoroughly read the instructions in his handbook In order to obtain the best resells.
1) BURNERS A diagram is screen-printed above ach knob on the front panel. This diagram indicates to which burner the knob in question corresponds. Afr hiving opened the as mains o gas bottle tap, fight the boomers as described below: Manual ignition Tum the knob corresponding o the required burner in an anticlockwise direction unit it reaches the full on position {sarge flame Aig. 1), then place & lighted match near the boomer.
Matches can be used to ignite the burners in a blackout. Aver allow children to posy near the appliance when using the burrs, Check that the pan handles are positioned correctly. The user should never heave the appliance unattended when cooking with easily inflammable olf and fat, Never use this appliance for heating purposes! This appliance must raven be operated without supervision Never use aerosols near the appliance when it Is operating.
[IMPORTANT INSTALLATION INSTRUCTIONS The Inst alter should onto that side walls to the appliance should be 1o higher than the hof plate it sol, Furthermore, the roar wall, the surfaces surrounding and adjacent to the appliance must be albs to withstand an temperature rise of 75° C (ambient temperature to be addenda.
10} ELECTRICAL CONNECTIONS “The data label can be found on the underside of the hob. Check that the voltage rating of the appliance corresponds 1o the supply voltage. The habit is supplied with 2 3 core cable which is fetid with a 13 amp plug. Make sure that the fitted fuse s the correct rating, For your safety please read the following information. The electrical connections of the appliance must be carried out In compliance with the provisions and standards in farce.
IMPORTANT At ways disconnect the appliance from the gas and electricity mains before carrying out any cleaning operation. 2) HOT PLATE Periodically wash the enameled steel pan supports G, the anathematized burr caps L., the boomer heads M and flame rings N (see fig.6) with warm soapy water, Those parts should be fined and dried before they ars practiced on the hob.
TECHNICAL INFORMATION FOR THE INSTALLER installation, adjustments of controls and maintenance must only be varied out by 2 qualified engineer. Incorrect installation may cause damage o persons, animals o property for which the Manufacturer sail not be considered responsible. During the life of the system, the automatic Safety or regulating devices on the appliance may only be modified by the manufacturer or by his duly authorized dealer.
Always disconnect the appliance from the electricity and gas mains before processing with any servicing operation. 13) REPLACING HOB PARTS When parts housed within the hot plats need replacing, it is first necessary fo remove the hab itself from the work surface, to postpartum i, unscrew screws V and to remove part T (see fig. 14). After having varied out the above sifted operations, the bu mars (g 15), taps (fig 16) and electrical components can all be replaced (fig.17).
NG CABLE TYPES AND SECTIONS TYPE OF TYPE OF BUNGLE-PHASE HOT PLATE CABLE POWER SUPPLY Gas hot plate 05 RRF' Section 3 x 0.75 mm” ATTENTION 11f if the prows supply cable is replaced, the install should heave the ground wire finger than the phase conductors {1ig.20} and comply with the recommendations given in paragraph 10, E GM 0009 312136 CATEGORY = equalize G 30 (BUTANE]) = 28 mar G 31 (PROPANE) = 37 mar G 20 {NATURAL) = 20 mar TOT. NOM. GAS RATE = 7.8 kW TOT. NOM. LP.G.
Al seals must e replaced by the technician aft he end of any adjustments or regulations. Our burners do not require primary air adjustment. 11} TAPS Our taps are suitable for alf the gas, they are male conical type at one way. “Reduced rate” adjustment Switch on the boomer and turn the relative knob to the “Reduced rate” position (small flame fig. 1). Remove knob M (fig,12) of the tap, which s simply pressed on o ts rod. b S G Ginning Insert a slam screwdriver D anti hole C (fg.
12} REPLACING THE INJECTORS The boomers can be adapted to different types of gas by exchanging the injectors to sail to the type of gas in question. To do this, first remove he burner tops using & wrench B. Now unscrew injector A (see fig.13) and fif a injector corresponding to the utilized types of gas in s place. Otis advisable to strongly tighten fhe injector in place.