COMPETENCE 3210 BU Build Under Double Oven Operating And Installation Instructions
IMPORTANT SAFETY INFORMATION These warnings are provided in the interests of your safety. Ensure that you understand them all before installing or using the appliance. Your safety is of paramount importance. If you are unsure about any of the information in this book contact the Customer Care Department. Telephone 0870 5 350350 INSTALLATION Never line any part of the appliance with aluminium foil. The appliance must be installed according to the instructions supplied.
CONTENTS FOR THE USER Important Safety Information Description of the Appliance Getting to Know Your Oven Before Using The Appliance When First Switching On Rating Plate Preparing to Use Your Appliance Condensation and Steam Cookware The Cooling Fan for the Controls Control Panel Indicator Neons Grill and Oven Furniture 2 4 5 6 6 6 6 6 7 7 7 8 The Electronic Timer 9 The Dual Grill Uses of the Grill How to use the Dual Grill Things to Note The Grill Pan and Handle Hints and Tips Grilling Chart 12 12 12
DESCRIPTION OF THE APPLIANCE Built in electric double oven WARNING: THIS APPLIANCE MUST BE EARTHED Electronic Timer Dual Grill Top Oven Fan Oven Your built in appliance comprises of a conventional oven and dual grill in the top compartment. The top oven is convenient and economical for mid-week use because of its size. The main fan oven is the larger of the two ovens. It is particularly suitable for cooking larger quantities of food. The main fan oven can be automatically controlled by the timer.
GETTING TO KNOW YOUR OVEN The Control Panel Electronic timer Grill Indicator Neon Dual Grill Control Top Oven Indicator Neon Top Oven Temperature Control Fan Oven Indicator Neon Fan Oven Temperature Control 5
BEFORE USING THE APPLIANCE WHEN FIRST SWITCHING ON The timer must be set to manual operation before the fan oven can be operated. This must be done whenever the appliance is switched off at the wall or when there has been a power failure. For instructions on how to set the timer see page 9. If the Fan oven indicator neon does not glow when the oven controls are switched on, it is most likely that the timer is set for automatic cooking.
COOKWARE Baking trays, dishes etc., should not be placed directly against the grid covering the fan at the back of the oven. Do not use baking trays larger than 30cm x 35cm (12” x 14”) as they will restrict the circulation of heat and may affect performance. Advice on the effect of different materials and finishes of bakeware is given in ‘Hints and Tips’ in the appropriate oven section. Note. The meat tin should not be placed on a heated hotplate as this may cause the enamel to crack.
GRILL AND OVEN FURNITURE The following items of oven furniture have been supplied with the appliance. 1 grill pan 1 grill pan handle 1 grill pan grid 1 meat tin 1 Stayclean Grill Deflector 1 shelf for grilling and Top oven cooking 2 shelves for Fan oven cooking The grill deflector sits above the grill element and prevents fat splashing onto the grill roof. The deflector may be easily removed for cleaning. Scuffing of the Stayclean panel/s by the oven furniture pack may occur during transit.
THE ELECTRONIC TIMER The electronic timer can indicate the time of day, operate as a minute minder and automatically time the fan oven. A Cookpot Symbol Auto Symbol (automatic cooking) Bell Symbol (minute minder) Auto Symbol Cookpot Symbol (manual cooking) Please note that this is a 24 hour clock, for example 2pm is shown as 14.00. If the oven is switched off at the wall or there is loss of power the clock will stop and you will not be able to use the appliance.
AUTOMATIC TIMER CONTROL The automatic timer can be used with the fan oven only. TO SWITCH THE FAN OVEN ON AND OFF AUTOMATICALLY 1. Ensure the clock is showing the correct time of day. 2. Place food in the fan oven. 3. Set the length of time you want the food to cook for by pressing the + button until the correct cooking time is displayed. This must be completed within 5 seconds of pressing the button. The maximum cooking time is 23 hours 59 minutes. The Cookpot and Auto symbols will show in the display.
RETURNING THE APPLIANCE MANUAL OR TO CANCEL AUTOMATIC PROGRAMME TO AN Once automatic cooking is complete an alarm will sound and the Auto symbol will flash to remind you that the oven needs to be set for manual operation. 1. To do this press buttons and together. After a few seconds the timer will show the time of day. The cookpot will show in the display and the oven will switch on again. 2. Turn off the oven control.
THE DUAL GRILL WARNING – Accessible parts become hot when the grill is in use. Keep children away. USES OF THE GRILL The grill is situated in the Top oven compartment. The grill is a dual circuit grill which means that the full area of the grill or the centre section only can be used. Use the centre section for economy purposes when cooking smaller quantities. HOW TO USE THE DUAL GRILL 1. Open the Grill / Top Oven door. 2.
THE GRILL PAN AND HANDLE The grill pan has a removable handle. To insert the handle, press the button on the handle with the thumb and pivot slightly upwards inserting the lip into the widest part of the bracket. Move the handle towards the left, lower into position and release the button. Ensure the handle is properly located. To remove the handle, press the button on the handle with the thumb and pivot the handle slightly upwards and towards the right to remove from the bracket.
· The grill pan grid is reversible. This is useful if you want to cook foods of varying thicknesses. As a general rule, bread for toasting should be placed on the grid in the ‘high’ position in the grill pan. Foods such as chicken pieces or chops may be grilled using the grilling grid in the low position. · Food should be thoroughly dried before grilling to minimise splashing. Brush lean meats and fish lightly with a little oil or melted butter to keep them moist during cooking.
GRILLING CHART The chart below gives recommended cooking times and shelf positions. Remember that these are a guide and should be adjusted to suit personal taste. Note: Shelf positions are counted from the bottom upwards.
THE TOP OVEN USES OF THE TOP OVEN The Top oven is the smaller of the two ovens. The Top oven is a conventional oven, i.e. without a fan. It is convenient where smaller quantities or convenience foods are being cooked. It is important to refer to the cooking chart as a guide to shelf positions and temperatures as these may differ from previous appliances you may have used. HOW TO USE THE TOP OVEN 1. Turn the Top Oven temperature control to the required setting.
HINTS AND TIPS · Use the Top oven when you want to warm plates. Use a setting of 80°C – 100°C on the oven temperature control. · For the best results use one shelf in the Top oven. For the best results food should be placed in the centre of the oven. To increase top browning e.g. for au gratin dishes, the food should be placed towards the top of the oven. Similarly for foods which benefit from the base being browned, e.g. pizza, quiches and flans, place the food on a lower shelf.
TOP OVEN COOKING CHART Note: Shelf positions are counted from the bottom upwards.
THE FAN OVEN USES OF THE FAN OVEN The Fan oven is particularly suitable for cooking larger quantities of food, or for weekend or celebration meals. The advantages of Fan oven cooking are: PREHEATING The Fan oven quickly reaches its temperature so it is not usually necessary to preheat the oven. Without preheating however you may need to add an extra 5 – 10 minutes on the recommended cooking times. For recipes needing high temperatures e.g. bread, pastries, scones, soufflés etc.
TO FIT THE FAN OVEN SHELVES The shelves should be fitted with the straight rods uppermost on the frame and the forms towards the back of the oven. If not fitted correctly the anti-tilt and safety stop mechanism will be affected. HINTS AND TIPS · Arrange the shelves in the required positions before switching the oven on. Shelf positions are counted from the bottom upwards.
FAN OVEN COOKING CHART The oven temperatures are intended as a guide only. It may be necessary to increase or decrease the temperatures by a further 10°C to suit individual preferences and requirements. Note: Shelf positions are counted from the bottom of the oven.
ROASTING CHART ROASTING CHART INTERNAL TEMPERATURES – Rare : 50-60°C, Medium : 60-70°C, Well done : 70-80°C MEAT FAN OVEN COOKING TIME 20-35 minutes per ½kg (1lb) and 20-35 minutes over Beef 160 – 180°C Beef, boned 160 – 180°C 25-35 minutes per ½kg (1lb) and 25-35 minutes over Mutton and Lamb 160 – 180°C 25-35 minutes per ½kg (1lb) and 25-35 minutes over Pork and veal 160 – 180°C 30-40 minutes per ½kg (1lb) and 30-40 minutes over Ham 160 – 180°C 30-40 minutes per ½kg (1lb) and 30-40 minutes
DEFROST FEATURE USES OF DEFROST FEATURE This fan oven function enables you to defrost most foods without heat faster than some conventional methods as the oven fan circulates air around the food. It is particularly suitable for delicate frozen foods which are to be served cold e.g. cream filled gateaux, cakes covered with icings or frostings, cheesecakes, biscuits, scones etc. HOW TO DEFROST 1. Turn the Fan oven temperature control to Defrost setting.
CARE AND CLEANING Before cleaning the appliance always allow the cooling fan for the controls to cool the appliance down before switching off the electricity supply. CLEANING MATERIALS Before using any cleaning materials on your appliance, check that they are suitable and that their use is recommended by the manufacturer. Cleaners that contain bleach should NOT be used as they may dull the surface finishes. Harsh abrasives should also be avoided.
CLEANING THE OUTER AND INNER DOOR GLASS PANELS To prevent damaging or weakening of the door glass panels avoid the use of the following: · Household detergents and bleaches · Impregnated pads unsuitable for nonstick saucepans · Brillo/Ajax pads or steel wool pads · Chemical oven pads or aerosols · Rust removers · Bath/Sink stain removers The outer oven door glass panels are removable for cleaning. TO REMOVE THE OUTER GLASS 1.
TO REPLACE THE OUTER DOOR GLASS 1. Holding the oven glass with both hands, gently place the locators into the holes of the brackets at the bottom of the oven door. 2. Holding the door glass with your left hand, use your right hand to open the oven door. Bring the door gently towards the glass panel ensuring the screw location holes line up. 3. Place the trim in the correct position on the top of the grill door. 4.
TO REMOVE THE WIREWORK RUNNERS The wirework runners in both ovens can be removed for cleaning. 1. Remove all shelves and furniture from the oven. 2. Hold the wirework at the bottom, unclip from the cavity side an gently pull towards the centre of the oven. 3. Support the side panel at the bottom. 4. Unhook the runner and side panel at the top and remove from the cavity. 5. To replace, ensure the side panel is assembled on to the wirework runner before hooking it back into the oven.
THE OVEN CLEANING CYCLE – BOTH OVENS 1. Remove oven shelves, wirework runners and bakeware from oven. 2. If cleaning the top oven, leave the grill deflector in place. 3. Turn the required oven temperature control to 220°C and allow the oven to run for an hour or so. THINGS TO NOTE · The oven indicator neon will glow until the oven has reached the desired temperature and then go out. It will then turn on and off showing that the oven temperature is being maintained.
· Use minimal, if any, extra oil or fat when roasting meat, potatoes only require brushing with fat before cooking. Extra fat in the oven during roasting will increase splashing and soilage. · It is NOT necessary to add water to a meat tin when roasting. The water and the fat juices from the joint create excessive splattering during cooking – even at normal temperatures, as well as causing condensation. · Covering joints during cooking will also prevent splashing onto the interior surfaces.
SOMETHING NOT WORKING? NOTES Please carry out the following checks on your appliance before calling a Service Engineer. It may be that the problem is a simple one which you can solve yourself without the expense of a service call. If our Service Engineer finds that the problem is listed below you will be charged for the call whether or not the appliance is under guarantee. Please note that it will be necessary to provide proof of purchase for any in-guarantee service calls.
The Oven Light fails to illuminate The Oven Light bulb may need replacing see page 29. If the Fan Oven is set for automatic cooking the light will illuminate when the cook time begins. The Oven Fan is noisy Check that the Oven is level. Check that the shelves and bakeware are not vibrating in contact with the oven back panel. The Oven temperature is too high or low Check that the recommended temperatures and shelf positions are being used. See page 21.
GUARANTEE CONDITIONS NOTES Standard guarantee conditions AEG offer the following guarantee to the first purchaser of this appliance: 1. The guarantee is valid for 12 months commencing when the appliance is handed over to the first retail purchaser, which must be verified by purchase invoice or similar documentation. The guarantee does not cover commercial use. 2. The guarantee covers all parts or components which fail due to faulty workmanship or faulty material.
SERVICE AND SPARE PARTS In the event of your appliance requiring service, or if you wish to purchase spare parts please contact your local Service Force Centre by telephoning: Before calling out an engineer, please ensure you have read the details under the heading ‘Something Not Working?’. 0870 5 929929 When you contact the Service Force Centre you will need to give the following details: Your call will be routed to the Service Force Centre covering your post code area. 1. 2. 3. 4.
TECHNICAL DETAILS Voltage: NOTES 230\240 Volts AC 50Hz Loading Info: Top Oven* 1.7kW Dual Grill: 2.8kW Base Element 1.0kW Main Oven Fan Element: 2.5kW Fan Motor: 0.03kW Oven Light: 0.05kW Wattage: 5.0\5.5kW Height: 720 mm Width: 593 mm Depth: 585 mm (excluding handles and knobs) Weight: 52kg * Cannot be used at the same time as the grill element This appliance complies with: European Council Directive 73/23/EEC. ECM Directive 89/336/EEC. CE Marking Directive 93/68/EEC.
INSTALLATION INSTRUCTIONS NOTES WARNINGS WARNINGS: · This appliance must be installed by a qualified electrician/competent person. Safety may be impaired if installation is not carried out in accordance with these instructions. · This appliance must be earthed. · Do not remove the screws from the earth tab extending from the oven mains terminal block (Fig. 1). · Before connecting the appliance make sure that the voltage of your electricity supply is the same as that indicated on the rating plate.
INSTALLATION INSTRUCTIONS NOTE: It is good practice to : · Fit an Earth Leakage Circuit Breaker to your house wiring. · Wire your appliance to the latest IEE regulations. THINGS TO NOTE · This appliance is designed to be fitted between cabinets with the recommended dimensions as shown in Fig. 3 & 4. · If there is an existing housing unit it must be removed. · The dimensions given provide adequate air circulation around the unit within the cabinet, ensuring compliance with BS EN60-335.
INSTALLATION INSTRUCTIONS NOTES PREPARING CABINET FOR FITTING OVEN · Make sure the space between the cabinets is the correct size for the appliance to be fitted (Ref. Fig. 5 & 6). · The plinth board spanning the space into which the appliance is to be installed should be removed. · If the size between adjacent cabinets is 605610*mm, then the cabinets should be modified so that the recommended dimension of at least 600605mm is maintained.
INSTALLATION INSTRUCTIONS · Check that the mounting brackets are level. They can be adjusted if necessary by using the extra holes at the ends of the brackets. Once the brackets are level, drill a pilot hole through the central hole in the bracket and fit the remaining screw. HOW TO FINISH UNPACKING · Place appliance next to the space in which it will be installed. See Fig 8.
INSTALLATION INSTRUCTIONS NOTES TO REMOVE COVER OF MAINS TERMINAL From the rear of the appliance, remove mains input terminal cover to gain access to terminal block. · First remove retaining screw with pozidrive screwdriver. See Fig. 9. Fig. 9 · Prise cover loose using screwdriver in position (1) then lever off with screwdriver in position (2) at either side. See Fig. 10. Fig.10 Lift cover and remove screw from cable clamp. See Fig. 11. Fig.
INSTALLATION INSTRUCTIONS CONNECTING TO THE MAINS TERMINAL Warning: This appliance must be earthed. · We recommend you use a new length of 6mm twin core and earthed cable to ensure your safety. · Make connection as shown in Fig. 12 by proceeding as follows:- · Preform wires to the appropriate shape to suit fitting into the mains terminal block. · Strip inner wirestrippers. 2 insulation on wires using · Twist the bared wires using pliers.
INSTALLATION INSTRUCTIONS NOTES CHECKING ELECTRICAL CONNECTIONS · Confirm the appliance is correctly connected by switching on and observing the various oven functions indicators. · The electronic timer will flash on and off. CONNECTING TO A HOB OR COOKER POINT · Either follow in general terms the instructions for connecting to the terminal block or refer to the hob suppliers installation instructions. Feed the cable through the cabinet and arrange to route the cable away from the appliance.
INSTALLATION INSTRUCTIONS FITTING INTO THE SPACE BETWEEN CABINETS IMPORTANT: Ensure that the oven is switched off at the wall before any further work is carried out. · Ensure the appliance is in front of the cabinet. See Fig. 13. · Take out all oven furniture before installation to reduce the weight you need to lift. · To place the appliance into the space between cabinetry follow the procedure below: · N.B. Two people will be required to carry out the lifting procedure.
NOTES 43
IMPORTANT NOTICE In line with our continuing policy of research and development, we reserve the right to alter models and specifications without prior notice. This instruction booklet is accurate at the date of printing, but will be superseded if specifications or appearance are changed. AEG, 55 – 77 HIGH STREET, SLOUGH, BERKSHIRE, SL1 1DZ. TELEPHONE 0870 5 350350 http://www.aeghome.co.
