Equipment Operation of tune extractor hood important! The appliance may only be switched on when fully installed, i.e. with applied pipe section and outlet grille {return air operation} or with connected exhaust air pipe system {exhaust air operation)! Appliance description (Fig.
Technical data Fan outputs to DIN 44971 Setting 1 Setting 2 Setting “Min.” “Max.” setting setting 310 D/410 D (3 settings) exhaust air 135 190 265 arboretum 100 160 230 320 D/420 D (continuously variable} exhaust air 135 2865 return air 100 230 *Exhaust air with 120 mm dia. pipe system; return air with KAFKA Original Carbon Filter Accessories and fittings 410D/420D 2 Side parts with mounting templates applied’) possessive screws {for joining side parts to housing) 6 A 3.
Electrical installation Electrical connection (appliances with connected load below 3000 watts) Warning! All appliances with a 3 core lead must be earthed. Voltage and current Please ensure that the voltage and current indicated on the rating plate agree with the voltage of your electricity supply. 220/240 volts — (i.e. 2201240 Va.c} Electrical connection Please note! (For users in the UK.
Electrical installation Arrangement of the protective contact plug socket directly above the fume extractor hood or above the overhead cabins confers two advantages: 1. The plug socket is not visible. 2. You can easily DE-energize the appliance where necessary by unplugging it. For the necessary fixed connection, the fume extractor hood should be connected only by an electrical instanter registers with the competent electricity supply company. Isolationist device is to be provided on the fixed wiring side.
Prior to installation Preparation as exhaust air appliance H the kitchen fume is run out anti the open air through the external wall, you need a telescopic wale box {special accessory, Fig, 4). Order via AEG after-sales service or dealership; wall box with supply and exhaust air duct. For dimensions and position of air outset openings: (Fig. 5) 410 D/420 D {Fig. For exhaust air connection of the fume extractor hood to the wall box, it is best to use non-flammable exhaust air hose E-No.
Prior to installation Preparation of furniture surround for exhaust air operation The design of 416 D/420 D appliances enables the exhaust air hose to be run backwards or 1o the side. After removal of the cover panel {Fig.
Installation 9. The fume extractor hood is now to be completed depending on operating mode: Exhaust air operation: Couple exhaust air system with exhaust air connection-piece on appliance side. Refit cover panel. Return air operation: Fit pipe connection through furniture ceiling on exhaust air connection-piece an appliance side. Place outlet grille on pipe connection and screw together with furniture ceiling (3.5 x 9.5) (Fig. 8).
Installation 4. Unscrew supplied complete mounting rat (see illustration on page 27/2 and 3} and screw together with appliance ceiling according to position relative to wall mounting angle (see illustration on page 27/1). 5. Fit wall end panel as illustrated on page 27/Table Y so that it remains adjustable for necessary height adjustment of appliance, 6. For fighting of side parts on fixed or separate furniture side wait, see page 26 {installation between two cabinets). 7.
Installation Fitting the furniture front panel on the fume protection panel installation of 410 D/420 D in furniture surround 1. Determine dimension between cabinet ceiling {bottom edge) and door top edge {neighboring cabinet) and mark in supplied template {dimension This dimension then corresponds to top edge of the furniture door, Place template centrally on rear of furniture front pane! {Fig. 22} and mark out mounting holes. N.B. Espadrille mounting holes 2.
Operation of fume extractor hood Function description ‘The individual numbers and symbols have the following meanings (from right to left): Fig. 25 Fig. 26 310D/410D 3200/420D Lighting *On/OH” £ L1 = Button pressed, Q= Motor switched off lighting switched off 1 = Setting 1 .D.
Maintenance and care Inserting/changing the grease filter (fleece} The grease filter with internet red stripes incorporated in the appliance is replaced by a new filter paper when the red stripes and/or the mark “Please change” with E-No. and F-No. visibly come through, The filter should be changed every 2-3 months depending on use, When repurchasing (special accessory}, please note the special instructions for installation of the filter fleece and washable metal grease filter in the retrofitting kit. 1.
Cleaning important! To clean the fume extractor hood, DE-energize the appliance {e.g. put out mains plug). At least once per year, you should clean internal surfaces of your appliance free of grease deposits to ensure that its full reliability is retained. Okd grease residues are highly flammable. Supersaturated grease and deodorization filters are therefore also to be avoided. Clean the external parts with a mild washing-up liquid solution. Never use abrasive detergents, brushes, or scouring powders.
AEG Tannhauser AG Posthaste 1036 D-80327 Nirenberg 1 © Copyright by AEG H 260219100 AEG Domestic Appliances Lid Customer Care Department 85-77 High Street Slough Berkshire SL11DZ Telephone: 08705 350350