INSTRUCTIONS AND ADVICE FOR THE USE, INSTALLATION AND MAINTENANCE GAS FUELED BUILT-IN HOT PLATE Dewar Customer, Thank you for having purchased ane of our products. We ars certain that this new, modem, functional and practical appliance, butt with the vary highest quality materials, will meet your requirements In the best possible way. This appliance s easy (o use. It Is, however, important 1o thoroughly read the instructions in this handbook in order to obtain the best results.
e 1) BURNERS A diagram Is screen-printed above each knob on the front panel, This diagram indicates to which boomer the knob in question corresponds. After having opened the gas mains or gas bottle tap, light the boomers &s described below. Manual ignition Tum the nab corresponding to the required burner In an anticlockwise direction unit it reaches the full on position {sarge flame fig.
IMPORTANT: Matches can be used 1o ignite the burners In a blackout. Never allow children to play near the salience whom using the burners, Check that the pan shandies are positioned correctly. The user should never fave the appliance unattended when cooking with easily inflammable oft and fat. Never use this appliance for heating purposes! This appliance must never ba operated without supervision! Never use aerosols neat the appliance when It is operating.
IMPORTANT Always disconnect the appliance from the gas and electricity mains before carrying out any cleaning operation. 2) HOT PLATE Periodically wash the enameled steel pan supports G, the enameled boomer caps L, the boomer heads M and flans dings N (see fig.6) wile warm soapy water. These pars ‘should be rinsed and dried before they are replaced on the hob. IMPORTANT Before refitting flame rings N, 1 is essential to check that the holes have not become clogged by foreign bodies.
TECHNICAL INFORMATION FOR THE INSTALLER Installation, adjustments of controls and maintenance must ably be carried out by a quantified engineer. incorrect installation may cause damage fo persons, animals or property for which the Manufacturer shall not be considered responsible. During the lite of the system, the automatic safety or regulating devices on the appliance may only be modified by the manufacturer or by his duly authorized dealer.
IMPORTANT INSTALLATION INSTRUCTIONS The installer should note that side walls 1o the appliance should be no higher than the hot plate itself. Furthermore, the rear wail, the surfaces surrounding and adjacent to the appliance must be able to withstand an temperature sirs of 76° C (ambient temperature o be added).
s 10) ELECTRICAL CONNECTIONS The data fable can be found on the underside of the hob. Check that the voltage rating of the appliance corresponds 1o the supply voltage. The hob is supplied with a 3 core cable which s fitted wife a 13 amp plug. Make sirs that the fitted fuse is the correct rating. For your safety please read the following information The electrical contractions of the appliance must be carried out in compliance with the provisions and standards in force.
At ways disconnect the appliance from the electricity main before making any adjustments. Al seals must be replaced by the technician at the end of any adjustments or regulations. Qur burners do not require primary air adjustment. 1) TAPS Our taps are suitable for all the gas, they are maize conical type at one way. “Reduced rate” adjustment Switch on the boomer and turn the relative knob to the "Reduced rate” postilion (small flame fig. 1). Remove knob M (ig.
12) REPLACING THE INJECTORS The boomers can be adapted fo different types of gas by exchanging the injectors to suit to the type of gas in question. To do this, first remove he burner tops using @ wrench B, Now unscrew injector A (sea fig.13) and il a injector corresponding to the utilized type of gas in its place. Otis advisability to strongly tighten the injector in claps.
At ways disconnect the appliance from the electricity and gas mains before processing with any servicing operation. 13) REPLACING HOB PARTS When parts housed within the hot piste need replacing, it is first necessary to remove the hob selfish from the work surface, to over tum it, unscrew sowers V and to remove part T (see fig. 14). Otter having carried out the above listed operations, the turners (g 15}, taps (fig.16} and electrical components can all be replaced (fg.17).
CABLE TYPES AND SECTIONS TYPE OF TYPE GF SINGLE-PHASE HOT PLATE CABLE POWER SUPPLY Gas hot piste HOS RR7 Section 3 x 0.75 mm? ATTENTION {1} If the power supply cable is replaced, the installer should slave the ground wire longer than the phase conductors {fig.20) and comply with the recommendations given In paragraph 10, £ GM 0005 312136 CATEGORY = lizard G 30 (BUTANE) = 28 mar © 3¢ (PROPANE) = 37 mar G 20 (NATURAL} = 20 mar TOT. NOM. BAS RATE = 7.6 kW TOT. NOM. LP.G.