Hob © Electrolux Household Appliances Ltd 2001 Tip. Montagnani - Mo - Cod.
Installation options For Your Safety 20 min When constructing the cabinet, suitable precautions must be taken to prevent contact with the casing of the hob, which becomes very hot during operation.The recommended method for overcoming this problem is illustrated in fig. 1. 30 On base cabinet with door a 60 b Installation The panel underneath the hob must be easily removable to allow the hob to be locked in position and released in case of servicing work. Fig.
Child safety • This hob is designed to be operated by adults. Do not allow children to play near or with the hob. Building into fitted kitchen units • The hob gets hot when it is in use. Children should be kept away until it has cooled. • Children can also injure themselves by pulling pans or pots off the hob. 70 Cleaning and maintenance • Keep the appliance thoroughly cleaned. Food residues may cause fire risks.
Replacing the power supply lead If the lead has to be replaced, only HO5RR-F or HO5RN-F type cables suitable for the load and the operating temperature must be used.In addition, the yellow/green earth wire must be about 2 cm longer than the live and neutral wires. In all cases, the power supply lead must be positioned so that it does not reach a °C above the room temperature in any point. One example of an ideal route is shown in the illustration.
Description of the hob Electrical connection 2 6 1.Hob 2.Medium semi-rapid burner 4 3.Small auxiliary burner 4.Large rapid burner 3 6.Triple flame burner 5 1 5.Burner control knobs 2 Instructions for use Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory. The hob control knobs The symbols on the control knobs mean the following: no gas flow maximum gas flow minimum gas flow WARNING: THIS APPLIANCE MUST BE EARTHED.
Connection to the gas supply Ensure that the gas type at the installation site is the same as that stated on the appliance rating plate. On the end of the shaft, which includes the GJ 1/2” threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force. Lighting the burners To obtain a flame more easily, light the burner before placing a cooking utensil on the pan stand.
Cleaning and maintenance Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. General cleaning Wash enamelled parts with lukewarm water and detergent; do not use abrasive products which might damage them. Wash the flame caps and burner caps often with boiling water and detergent, taking care to remove all deposits.
Something Not Working Technical Data If the hob is not working correctly, please carry out the following checks before contacting your local AEG Service Force Centre.
Service and Spare Parts Guarantee Conditions If you require spare parts or an engineer contact your local Service Force Centre by AEG offer the following guarantee to the first purchaser of this appliance: 1. The guarantee is valid for 12 months commencing when the appliance is handed over the first retail purchaser, which must be verified by purchase invoice or similar documentation. The guarantee does not cover commercial use. 2.
Service and Spare Parts Guarantee Conditions If you require spare parts or an engineer contact your local Service Force Centre by telephoning: AEG offer the following guarantee to the first purchaser of this appliance: 1. The guarantee is valid for 12 months commencing when the appliance is handed over the first retail purchaser, which must be verified by purchase invoice or similar documentation. The guarantee does not cover commercial use. 2.
Something Not Working Technical Data If the hob is not working correctly, please carry out the following checks before contacting your local AEG Service Force Centre.
Cleaning and maintenance Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. General cleaning Wash enamelled parts with lukewarm water and detergent; do not use abrasive products which might damage them. Wash the flame caps and burner caps often with boiling water and detergent, taking care to remove all deposits.
Connection to the gas supply Ensure that the gas type at the installation site is the same as that stated on the appliance rating plate. On the end of the shaft, which includes the GJ 1/2” threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force. Lighting the burners To obtain a flame more easily, light the burner before placing a cooking utensil on the pan stand.
Description of the hob Electrical connection 2 6 1.Hob 2.Medium semi-rapid burner 4 3.Small auxiliary burner 4.Large rapid burner 3 6.Triple flame burner 5 1 5.Burner control knobs 2 Instructions for use Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory. The hob control knobs The symbols on the control knobs mean the following: no gas flow maximum gas flow minimum gas flow WARNING: THIS APPLIANCE MUST BE EARTHED.
Replacing the power supply lead If the lead has to be replaced, only HO5RR-F or HO5RN-F type cables suitable for the load and the operating temperature must be used.In addition, the yellow/green earth wire must be about 2 cm longer than the live and neutral wires. In all cases, the power supply lead must be positioned so that it does not reach a temperature 50°C above the room temperature in any point. One example of an ideal route is shown in the illustration.
Child safety • This hob is designed to be operated by adults. Do not allow children to play near or with the hob. Building into fitted kitchen units • The hob gets hot when it is in use. Children should be kept away until it has cooled. • Children can also injure themselves by pulling pans or pots off the hob. 70 Cleaning and maintenance • Keep the appliance thoroughly cleaned. Food residues may cause fire risks.
Installation options For Your Safety 20 min When constructing the cabinet, suitable precautions must be taken to prevent contact with the casing of the hob, which becomes very hot during operation.The recommended method for overcoming this problem is illustrated in fig. 1. 30 On base cabinet with door a 60 b Installation The panel underneath the hob must be easily removable to allow the hob to be locked in position and released in case of servicing work. Fig.
Hob © Electrolux Household Appliances Ltd 2001 Tip. Montagnani - Mo - Cod.