2460 D/2490 D Dunstabzugshaube Afzuigkap Hotte aspirante Cooker Hood Montage- und Gebrauchsanweisung Installatie- en gebruiksaanwijzing Manuel de montage et d’utilisation Operating and Installation Instructions
Contents 48 Safety warnings for user for kitchen unit installer 49 49 49 Introduction Extractor version Filter Version 51 51 51 Bedienung der Dunsthaube 52 Maintenance and care Metal grease filter Open the metal grease filter Carbon filter Changing the light bulb 53 53 53 54 55 Cleaning 56 Special accessories 56 Technical assistance service 56 Guarantee conditions 57 Technic Details Mounting accessories included 59 59 Electrical connection Safety warnings for the electrician Wall unit mo
Safety warnings for user • Always cover lighted elements, to prevent excess heat from damaging the appliance. In the case of oil, gas and coal fired cookers it is essential to avoid open flames. • Also, when frying, keep the deep frying pan on the cooker top/ cooker under careful control. • The hot oil in the frying pan might ignite due to overheating. • The risk of self-ignition increases when the oil being used is dirty. • It is extremely important to note that overheating can cause a fire.
• It is advisable to apply for authorization from the relevant controlling authority when connecting the outlet to an unused chimney flue or combustion gas duct. The air outlet installation must comply with the regulations laid down by the relevant authorities. • When the unit is used in its extractor version, a sufficiently large ventilation hole must be provided, with dimensions that are approximately the same as the outlet hole.
Introduction Extractor version • The hood is supplied as an extractor unit and can also be used with a filtering function by fitting one activated carbon filter (special accessory). • You will need original AEG carbon filter for this function (see Special Accessories). • The air is discharged to the outside through a pipe, which must be fitted to connection flange A. Fig. 1. • In order to obtain the best performance the hose should have a diameter equal to the outlet hole.
Fig. 2 Bedienung der Dunsthaube • The hood is fitted with one motor having several speed. Turn the hood on a few minutes before you start cooking then you will get an underpressure in the kitchen. It should be left on after cooking for about 15 minutes or until all odours have disappeared.
Maintenance and care • The hood must always be disconnected from the mains power supply before beginning any maintenance work. Metal grease filter • The purpose of the grease filters is to aspirate grease particles which form during cooking and it must always be used, either in the external evacuation or internal recycling function. Attention: the metal grease filters must be removed and washed, either by hand or in the dishwasher, every four weeks.
Carbon filter • The carbon filter should only be used if you want to use the hood in its filtering function. • To do this you will need an original AEG activated carbon filter (see special accessories). • Cleaning/replacing the carbon filter Unlike other carbon filters, the LONGLIFE carbon filter can be cleaned and reactivated. At normal use the filter should be cleaned every second month. The best way to clean the filter is in the dishwasher. Use normal detergent and choose the highest temperature (65º C).
Warning • Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. • The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations. Changing the light bulb • • • • • Disconnect the cooker hood from the main supply. Remove the lamp cover, use a screw driver as a lever.
Cleaning • Warning: always disconnect the hood from the mains power supply before cleaning it. Never insert pointed objects in the motor’s protective grid. • Wash the outside surfaces using a delicate detergent solution. Never use caustic detergents or abrasive brushes or powders. • Only ever clean the switch panel and filter grille using a damp cloth and delicate detergents. • It is extremely important to clean the unit and change the filters at the recommended intervals.
Guarantee conditions Guarantee Conditions AEG offer the following guarantee to the first purchaser of this appliance. 1. The guarantee is valid for 12 months commencing when the appliance is handed over to the first retail purchaser, which must be verified by purchase invoice or similar documentation.The guarantee does not cover commercial use. 2. The guarantee covers all parts or components which fail due to faulty workmanship or faulty materials.
Before you move please contact your nearest Customer Care Centre, listed below, to give them details of your new home.They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances.
Technic Details Models 2490 D 2460 D Dimensions - extractor ver (in cm): Height Width Depht 68-113 89,8 45 68-113 59,8 45 Dimensions - filter version (in cm): Height 67,5-122,5 Width 89,8 Depht 45 67,5-122,5 59,8 45 Maximum absorbed power: 195 W 195 W Motor absorption: Lighting: 1 x 155 W 2 x 20W 1 x 155 W 2 x 20W Lenght of the cable: 140 cm 140 cm Mounting accessories included 6 wall plugs Ø 8 mm 6 wood-screws 5 x 45 mm 6 metal screws 2,9 x 6,5 8 metal screws 3 x 10 1 deflector 1 chimney s
Electrical connection Safety warnings for the electrician Before connecting the appliance to the power supply, check that the voltage indicated on the rating plate corresponds to the mains power supply available. Appliances fitted with a plug can be connected to any standard power socket within easy access. Should it be necessary to provide a fixed connection, the hood must only be installed by an electrician authorised by the local electricity board.
Wall unit mounting - Fig. 6 • Only for extractor version: position the upper section of the chimney so that the oulet slots H are not visible (see also A-B-C sequence on on Fig. 6). • Fix each other both parts of the hood (1), make all connections between the two parts (2) and fix with 6 screws (3).
A-B-C, Extractor version only! 20a 4 20a H G 14 14 20b 15 20b F 7-16 1 7-16 11 21 11 18 19 6 1 1 B 98 5 9 8 9 8 13 12 12 10 2 10 13 17 1 1 17 3 22 Fig.
AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.de © Copyright by AEG LI1LNC Ed.
