Contents Introduction 4 Extraction mode 4 Re circulation mode 5 Electrical connections 6 Technical details 7 Installation 8 Safety warnings for kitchen unit installer 8 Wall unit mounting 10 ‘Wall mounting i Hood operation 2 Safety warnings for user 13 Maintenance and care i4 Opening the grid 14 Grease filter 14 Carbon filter 15 Changing the Tight bulb 16 Cleaning 16 Accessories 17 Something not working 17 Service & Spare parts 8
Introduction Extraction mode @ The hood is supplied as an extractor unit and can also be used with a filtering function by fitting activated carbon filters (available as an accessory). ® The unit features two outlet holes, one of which A is located on the top of the unit while the other B is located on the rear.
® Move the lever L to position A — Fig. 3. ® When connecting up the hood using a telescopic wall pipe, you should use an inflammable outlet hose ABS 120 (120 mm @) available as an accessory. Re circulation mode ® The air is filtered and recirculated through the front grid. @ Move the lever L to position F — Fig. 3. You will need an original KFF activated carbon filter for filtering function. (Available as an accessory).
Electrical connection 220-240 V using fixed power supply line with plug, {The unit should only be connected up by an authorized electrician). Your appliance must be connected to fixed wiring via the use of a double pole switched fused spur cutlet with or without plat lamp.
Technical details Dimensions Height x Width x Depth 599 x 51 Weight Net: 6,9 kg Gross: 7.
Installation Safety warnings for kitchen unit installer ® When used as an extractor unit, the hood must be fitted with a 120mm diameter hose. @ If the fumes must be forced out through the wall, you must obtain a MKZ sizable wall exhaust pipe (with external exhaust and air intake), E-Nr.610 899 004 (& 120 mm) which is one of our optional parts.
® The national decree on fuel-burning systems specifies a maximum depression of 0.04 bar in such rooms. ® Hoods can only be used safely with appliances connected to a chimney if the room and/or flat (air/environment combination) is ventilated from outside using a suitable ventilation hole approximately 500-600 cm? large to avoid the possibility of a depression being created during operation of the hood. If you have any doubts, contact the relevant controlling authority or building inspector’s office.
Wall unit mounting @ Make the holes on the bottom of the cupboard, using the drilling template . ® From inside the cupboard, insert the 4 supplied screws and tighten them in the appropriate holes on the appliance. — Fig. 4.
Wall mounting @ Fix the drilling template to the wall. @ Make 3 @ Bmm holes in the wall 2 at points 1, 1 as desired at points L. ® Insert the three & 8mm expansion plugs into the wall. ® Insert 2 5x45 screws at points | but do not tighten them completely. ® Adjust the unit so that it is positioned at a right angle to the wall by turning the two support screws G. @ Fit the hood into holes §, tighten the 2 screws. @ From inside the hood, insert the third 5x45 screw into hole L. — Fig.
Hood Operation ® The hood is fitted with a variable speed motor. The most effective use of the hood is obtained by switching it on a few minutes before you start cooking and leaving it on a for approximately 15 minutes after you have finished, thus ensuring all cooking odors are eliminated.
Safety warnings for user ® Never leave a cooking hob or ring on without a pot or pan on top of it, to avoid the possibility of excess heat damaging the unit. Gas, oil in particular should never be left uncovered. ® Special care should be taken when using deep fat fryers since the oil in them can overheat and burst into flames. ® The risk of a fat fire increases when using dirty ofl. @ It is extremely important to note that overheating can cause a fire. @® Never carry out any flambe cooking under the hood.
Maintenance and care ® The hood must always be disconnected from the mains power supply before beginning any maintenance work. Opening the grid ® Open the latch L and swing the grille downwards. Fig. 6. ® To remove the grid, pull it forwards from the right and release it.
Removing the filter Open the grid and remove the stops M to take out the filter. See Fig. Carbon filter @ The activated carbon filter should only be used if you want to use the hood in its filtering function. @ To do this you will need an original AEG activated carbon filter {see special accessories). ® This filter cannot be cleaned or reused. @ As a general rule, the activated carbon filter should be changed once every four months. @ Mounting Fig 8 a. Fit first rearwards on the proper seats. b.
Warning @ Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. Changing the light bulb @ Disconnect the unit from the mains power supply. ® Remove the grid. ® Replace the old light bulb with a new light bulb (40 W Max.).
Accessories The following accessories can be ordered through your retailers. MKZ telescopic wall pipe outlet hose ABSI120,120 mm & Synthetic grease filter Metal grease filter MUFF Carbon filter KFF Something not working ¥ your appliance fails to work property please carry out the following checks. Symptom Solution The cooker hood will not start... The hood is connected to the electricity supply. Check that the fan speed contort is falsetto. The cooker hood is not working effectively...
Service & Spare Parts If you require a service engineer or wish to purchase spare parts, contact your local AEG Service Center, by telephoning: 0990 929929 Help us to help you Please determine your type of inquiry before telephoning. When you contact us we need to know. 1. Your name, address and post code 2. Your telephone number 3. Clear and concise details of the fault. 4. The model, serial number (E-NR) and the manufacturing number (F-NR} (This information can be found on the rating plate). 5.
AEG Exaggerate AG Posthaste 1036 D-80327 Nirenberg 1 © Copyright by AEG H 259 245 740 LIGATION AEG Domestic Appliances Ltd Customer Care Department 58-77 High Street Slough Berkshire SL1 1DZ Telephone: 08705 350350