15 D Extractor Hood Installation and Operating Instructions
Contents Introduction Extractor version Recirculating mode 3 3 4 Electrical connections Safety warnings for electrician 5 5 Specifications 8 9 9 10 11 Hood operation Safety warnings for user 12 12 Maintenance and care Opening the grille Grease filter carbon filter Changing the light bulb 13 13 13 13 14 Cleaning 15 Special Accessories 15 Technical Assistance Service 16 M A D E IN G E R O M K A N O Y SY ST EM Installation Safety warnings for kitchen unit installer Wall unit m
Introduction The hood is supplied as an extractor unit and can also be used with a filtering function by fitting activated carbon filters (special accessory). Extractor version The unit features two outlet holes, one of which A is located on the top of the unit while the other B is located on the rear. To connect up the hose, you should first fit the bayonet-mounting flange C (100 or 120 mm) on the outlet required (if using the top outlet, fix the flange in place using the screw supplied as shown in Fig.
The air is filtered and recirculated through the front grille. Move the handle F to position F — Fig. 3. EXHAUSTING ABLUFT EVACUATION ASPIRANTE MAX 40W RECIRCULATION UMLUFT RECICLAGE FILTRANTE A F F 3 You will need an original AEG KLF60/80 activated carbon filter for the recirculating mode. (See special accessories).
Electrical connections Voltage and current Please ensure that the voltage and current indicated on the rating plate agree with the voltage of your electricity supply. If your appliance has been equipped with a mains lead with a moulded-on type plug, you must comply with the following regulations: The plug moulded on to the lead incorporates a fuse. For replacement, use a 5 amp BS1362 fuse. Only ASTA approved or certified fuses should be used.
Your appliance must be connected to fixed wiring via the use of a double pole swiched fused spur outlet with or without pilot lamp. We strongly recommend the appliance is connected by a qualified electrician who is a member of the NICEIC who will comply with the IEE and any local regulations. NOTE: The terminology “DOUBLE POLE” means that both the live and neutral supplies are swiched and disconnected at the same time.
Appliances with 3 wires Your appliance must be connected to fixed wiring via the use of a double pole swiched fused spur outlet with or without pilot lamp. We strongly recommend the appliance is connected by a qualified electrician who is a member of the NICEIC who will comply with the IEE and any local regulations. NOTE: The terminology “DOUBLE POLE” means that both the live and neutral supplies are swiched and disconnected at the same time.
Specifications Dimensions: Height 152 Weight: Net: Gross: Width 599 Depth (in mm) 505 8.7 Kg 9.6 Kg Length of the cable: 140 cm Maximum absorbed power: 230 W Motor absorption: 1 x 150 W Lighting: 2 x 40 W Fan powers (levels), levels in compliance with DIN 44971 Level: Min. Extractor: 116 m3/h Filter: 60 m3/h Max.
Installation Safety warnings for kitchen unit installer When used as an extractor unit, the hood must be fitted with a 100 or 120 mm diameter hose. If the outlet hose is installed in a horizontal position, it must be slanted at an angle of 10° so that the air can flow outside without impediment. When installing the hood, make sure you respect the following minimum distance from the top edge of the cooking hob/ ring surfaces: electric cookers 650 mm gas cookers 650 mm coal and oil cookers 700 mm min.
Since the rule for rooms with fuel burning appliances is “outlet hole of the same size as the ventilation hole”, a hole of 500-600 cm2, which is to say a larger hole, could reduce the performance of the extractor hood. If the hood is used in its recirculating mode, it will operate simply and safely in the above conditions without the need for any of the aforementioned measures.
— Position the template on the wall. — Drill four 8 mm Ø holes in the wall, 2 in points H and 2 in points I. — Fit the four 8 mm screw anchor plugs in the wall. — Screw two 5 x 45 mm screws in points H but do not tighten them fully home. — Adjust the unit so that it is positioned at a right angle to the wall by turning the two support screws G. — Now hang the hood on the wall (holes H). Tighten the first two screws and, for safety’s sake, screw the other two 5 x 45 mm screws into the holes in the hood.
Hood Operation The hood is fitted with a variable speed motor. The most effective use of the hood is obtained by switching it on a few minutes before you start cooking and leaving it on a for approximately 15 minutes after you have finished, thus ensuring all cooking odours are eliminated.
Maintenance and care The hood must always be disconnected from the mains power supply before beginning any maintenance work. Opening the grille — Open the latch L and swing the grille downwards. — Fig. 7. — To remove the grille, pull it forwards from the right and release it.
Removing the filter — Press the stops N and remove the filter by pulling it downwards. — Fig. 8 N N 8 Always specify the hood model code number and serial number when ordering replacement filters. This information is shown on the registration plate located on the inside of the unit. The activated carbon filter can be ordered from AEG service. 14 Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard.
Cleaning Warning: always disconnect the hood from the mains power supply before cleaning it. Never insert pointed objects in the motor’s protective grille. Wash the outside surfaces using a delicate detergent solution. Never use caustic detergents or abrasive brushes or powders. Only ever clean the switch panel and filter grille using a damp cloth and delicate detergents. It is extremely important to clean the unit and change the filters at the recommended intervals.
Technical assistance service In case of any enquiries and faults, please call AEG After-Sales Service: AEG Domestic Appliances Limited Head Office: 217 Bath Road Slough, Berks SL1 4AW Tel: 01753 872506 Telefax: 01753 512271 AEG Northern Service Centre: Unit 20, Haigh Park Haigh Avenue Stockport GL Manchester SK4 1QR Tel: 0161 487 2205 Telefax: 0161 474 1191 AEG Scottish Service Centre: Block 11, Unit 1 Dundyvan Industrial Estate Coatbridge Lanarkshire ML5 4AQ Tel: 01236 440387 Telefax: 01236 440256 Servic
If your appliance has a fault, please contact our service engineer and state the following numbers: E-Nr. 610 F-Nr. AEG Hausgeräte AG Postfach 1036 D-90327 Nürnberg © Copyright by AEG H 260 287 140 L 489B Ed.
