11 K AUS ERFAHRUNG GUT Electric hob Table de cuisson électrique Operating Instructions GB Notice dutilisation FR
ENGLISH Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 350350 Installation l This hob must be installed by qualified personnel, according to the manufacturers instructions and to the relevant British Standards. Remove all packaging before using the hob. Ensure that the electrical supply complies with the type stated on the rating plate.
l l Never use plastic or aluminium foil dishes on the hob. Perishable food, plastic items and areosols may be affected by heat and should not be stored above or below the hob unit. Service l This hob should only be repaired or serviced by an authorised Service Engineer and only genuine approved spare parts should be used. {Environmental Information l l After installation, please dispose of the packaging with due regard to safety and the environment.
Contents For the user Important Safety Information 2 Description of the Hob 5 Operation 6 Hints and Tips 7 Maintenance and Cleaning 8 Something Not Working? 9 Service and Spare Parts 10 Customer Care 10 Guarantee Conditions 11 For the installer 4 Instructions for the Installer 12 Important safety requirements 12 Installation 13 Cut Out Size 13 Electrical connections 15 Wiring diagram 16
Description of the Hob Back Left Hotplate Front Left Hotplate Back Right Hotplate Back Left Hotplate Control Knob Front Right Hotplate Back Right Hotplate Control Knob Operating Pilot Lamp Front Right Hotplate Control Knob Front Left Hotplate Control Knob INSTALLATION The hob must be installed according to the instructions supplied. The hob must be installed by qualified personnel to the relevant British Standards.
Operation Electric Hotplates To switch on a hotplate, turn the relevant control knob anticlockwise to the required heat setting. The control knob is numbered 1 - 3 0 - OFF 1 - Minimum 3 - Maximum. The hob has four rapid hotplates. The rapid hotplates are indicated by a red dot, and will heat up more quickly than a normal plate. As the red dots are painted on the plate, they may deteriorate during use and even disappear completely after a period of time. This will not affect the performance of the hob.
Hints and Tips Saucepans for use on solid plates should have several characteristics: l l l They should be fairly heavy duty They should fit the heat area exactly, or be slightly larger for efficient use, NEVER smaller. They should have a flat base to ensure good contact with the plate. This is particularly important when using pans for high temperature frying or pressure cooking. As soon as liquid starts boiling, turn down the plate control knob so that it will barely keep the liquid simmering.
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing up liquid has been added.
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local AEG Service Force Centre. SYMPTOM n The plate does not heat up. SOLUTION u u u u n The plate is not giving satisfactory results u u u u Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped (if fitted) Check the mains fuse has not blown Check the correct control knob has been turned.
Service and Spare Parts If you require spare parts or an engineer contact your local Service Force Centre by telephoning: 0870 5 929 929 Your call will be routed to your local Service Force Centre. When you contact the Service Centre, they will need the following information: 1. Your name, address and post code. 2. Your telephone number 3. Clear and concise details of the fault 4. The model and the serial number (see rating label on the back of this instruction booklet) 5.
Guarantee Conditions AEG offer the following guarantee to the first purchaser of this appliance. 1. The guarantee is valid for 12 months commencing when the appliance is handed over to the first retail purchaser, which must be verified by purchase invoice or similar documentation. The guarantee does not cover commercial use. 2. The guarantee covers all parts or components which fail due to faulty workmanship or faulty materials.
Instructions for the Installer Engineers technical data OVERALL DIMENSIONS Width: Depth: Height: 580 mm. 500 mm. 88 mm. CUT OUT DIMENSIONS Width: Depth: 550 mm. 470 mm. SUPPLY CONNECTIONS Electric: 230-240V 50Hz supply. HEATING ELEMENTS RATING Rapid Front Left Hotplate Rapid Back Left Hotplate Rapid Back Right Hotplate Rapid Front Right Hotplate Total Rating Ø 180 mm. Ø 145 mm. Ø 180 mm. Ø 145 mm.
CLEARANCES REQUIRED WHEN FITTING THE HOB WITH A COOKER HOOD ABOVE CLEARANCES REQUIRED WHEN FITTING THE HOB WITHOUT A COOKER HOOD ABOVE 600 mm 700 mm 700650 mmmm 400 mm 55 50 m mm 400 mm m 100 400 mm 55 50 m mm m mm 50 m m 100 400 mm mm 50 m m FO 0813 FO 0812 Installation IMPORTANT This hob must be installed by qualified personnel to the relevant British Standards.
Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2.
Fitting the hob to the worktop Before fitting the hob into the cut out, a sealing gasket supplied with the hob must be fitted to the edge of the cut out. It is essential that no gaps are left in this seal in order to prevent spillage near the hob seeping into the cabinet below. 1) Place the sealing gasket all around the edge of the cut out. 2) Place the hob into the cut out and secure it by means of the relevant fixing clamps and screws, as shown in the diagram.
Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations. The switch must not break the yellow and green earth cable at any point. Ensure that the hob supply cord does not come into contact with surfaces with temperatures higher than 50 deg. C.
