DI 8610 - HI 8610 CHDI 8610 Dunstabzugshaube Afzuigkap Hotte Cooker Hood Montage- und Gebrauchsanweisung Installatie- en gebruiksaanwijzing Notice d’utilisation et d’installation Operating and Installation Instructions
Sehr geehrte Kundin, sehr geehrter Kunde, • lesen Sie bitte diese Benutzerinformation sorgfältig durch. Beachten Sie vor allem den Abschnitt „Sicherheit“ auf den ersten Seiten. Bewahren Sie bitte diese Benutzerinformation zum späteren Nachschlagen auf. Geben Sie sie an eventuelle Nachbesitzer des Gerätes weiter. Wir sind für Sie da: montags bis freitags 8.00 bis 20.00 Uhr AEG DIRECT samstags INFO SERVICES 0180 - 555 45 10.00 bis 14.00 Uhr.
Inhalt Sicherheitshinweise ......................................................................... 4 für den Benutzer ................................................................................. 4 für den Küchenmöbel-Monteur ........................................................... 5 Allgemeines ...................................................................................... 7 Abluftbetrieb .......................................................................................
Sicherheitshinweise für den Benutzer • Es muß darauf geachtet werden, daß Kochstellen bei Betrieb stets abgedeckt sind, damit nicht durch zu starke Hitzeentwicklung das Gerät beschädigt wird. Unbedingt zu vermeiden sind offene Feuerstellen bei Öl-, Gas- und Kohleherden. • Außerdem ist beim Fritieren über Herd/Mulde das zum Fritieren verwendete Gerät während des Betriebes zu beaufsichtigen.
für den Küchenmöbel-Monteur • Das Abluftrohr muß bei Abluftbetrieb vorzugsweise den Orignaldurchmesser des Gerätes haben. Achtung! Das Abluftrohr und die Befestigungsmanschetten sind nicht im Lieferumfang inbegriffen und müssen gesondert erworben werden. Falls ein Abluftrohr in Wand oder Dach mit einem Durchmesser von 125 mm schon besteht, kann der mitgelieferte Reduzierstutzen, 150/125 mm, verwendet werden.
Schornsteinfegermeisters oder der örtlichen Baubehörde einholen. • Da in Räumen ohne Feuerungsstätte die Regel gilt: “Zuluftöffnung so groß wie Abluftöffnung”, kann durch eine größere Öffnung als 500-600 cm2 der Wirkungsgrad der Ablufteinrichtung beeinträchtigt werden. • Der Betrieb der Dunstabzugshaube als Umlufthaube ist unter den genannten Umständen gefahrlos und unterliegt nicht den obengenannten Vorschriften.
Allgemeines • Die Dunstabzugshaube wird als Abluftgerät ausgeliefert und kann durch den Einsatz eines Aktivkohlefilters (Sonderzubehör) als Umluftgerät verwendet werden. • Für den Umluftbetrieb wird der Original-Aktivkohlefilter aus dem Sonderzubehör benötigt. • Nur für HI 8610: Die Dunstabzugshaube ist mit einem Aktivkohlefilter bereits ausgestattet. Falls die Abluftversion erwünscht ist, bitte den Kohlefilter entfernen.
Bedienung der Dunstabzugshaube • Die Dunsthaube ist mit einem Motor mit regelbarer Drehzahl ausgerüstet. Es ist ratsam, die Dunsthaube einige Minuten vor Beginn des Kochens einzuschalten und sie ungefähr 15 Minuten nach dem Kochen weiterlaufen zu lassen, damit alle Gerüche sicher entfernt werden.
Kontrollvorrichtung für Fett- und Aktivkohlefilter Diese Dunstabzugshaube verfügt über eine Vorrichtung, die anzeigt, wenn der Fettfilter beziehungsweise der Aktivkohlefilter zu reinigen ist (bei Umluftbetrieb mit Aktivkohlefilter). Diese Haube wird vom Werk aus ohne Aktivkohlefilter geliefert, deshalb ist ihre Sättigungsanzeige ausgeschaltet. Wird die Haube jedoch mit Aktivkohlefilter in Betrieb genommen, so ist diese Sättigungsanzeige wie folgt einzuschalten: Die Haube muss auf „AUS“ eingestellt sein.
Wartung und Pflege • Bevor irgendwelche Wartungsarbeiten ausgeführt werden, muss die Dunstabzugshaube vom Stromnetz getrennt werden. Metallfettfilter • Metallfettfilter haben die Aufgabe, Fettpartikel, die beim Kochen entstehen, aufzusaugen. Sie werden in jedem Fall, d.h. sowohl bei Abluft- als auch bei Umluftbetrieb, verwendet. Metallfettfilter sollen alle 4 Wochen im Geschirrspüler bzw. von Hand gereinigt werden.
Aktivkohlefilter • Der Aktivkohlefilter muß dann verwendet werden, wenn man die Dunstabzugshaube als Umluftgerät einsetzen möchte. • Dazu wird der Original Aktivkohlefilter (siehe Sonderzubehör) benötigt. • Reinigung/Austausch des Aktivkohlefilters Im Unterschied zu anderen Aktivkohlefiltern kann der LONG LIFE Aktivkohlefilter gereinigt und reaktiviert werden. Bei normaler Nutzung der Abzugshaube sollte der Filter jeden zweiten Monat (wenn man eine tägliche Benützung von ca. 2,5 Std.
Achtung • Nichtbeachtung dieser Anweisungen zur Reinigung des Gerätes und zum Wechsel bzw. zur Reinigung der Filter kann zum Brand führen. Diese Anweisungen sind unbedingt zu beachten! • Der Hersteller übernimmt keine Haftung für irgendwelche Schäden am Motor oder aus Feuergründen, die auf eine unsachgemäße Wartung oder Nichteinhaltung der oben angeführten Sicherheitsvorschriften zurückzuführen sind. Austausch der Lampe(n) • Dunstabzugshaube vom Stromnetz trennen.
Reinigung • Achtung: Zum Reinigen der Dunstabzugshaube Gerät vom Stromnetz trennen. Nicht mit spitzen Gegenständen in das Schutzgitter des Motors eindringen. • Äußere Teile mit milder Spüllauge reinigen. Scharfe Reinigungsmittel, Bürste oder Scheuersand vermeiden. • Die Schalterblende und das Fettfiltergitter nur mit feuchtem Tuch und milden Spülmitteln reinigen. • Es ist wichtig, die Filterwechsel sowie die Reinigungsintervalle einzuhalten.
Kundendienst Bei eventuellen Rückfragen und Störungen Kundendienst anrufen (siehe Kundendienst-Stellenverzeichnis). Folgende Daten beim Anruf angeben: 1. Modellbezeichnung 2. E-Nr. 3. F-Nr. Diese Daten befinden sich auf dem Typenschild auf der Innenseite des Gerätes hinter den Fettfiltern. Konstruktions- und Farbänderungen im Rahmen der technischen Entwicklung bleiben vorbehalten. SERVICE Handelt es sich um eine technische Störung? Dann wenden Sie sich an Ihre Kundendienststelle.
Technische Daten Maße (in cm): Höhe: Breite: Tiefe: Gesamtanschlußwerte: Lüftermotor: Beleuchtung: Länge des Netzkabels: Elektroanschluß: 80-108 100 70 250 W 1 x 160 W 4 x 20 W 150 cm 220-240V Zubehör/Montagematerial 1 Reduzierstutzen Ø 150-125 1 Umluftweiche + 6 Schrauben 3,5 x 13 1 Spannschlüssel für TORX-Schrauben 6 Schrauben 6 x 70 mm 6 Dübel Ø 10 mm 14Schrauben 4 x 7 mm + 14 Muttern (zur Befestigung der Kamine) 14Schrauben 4 x 8 mm (6 zur Befestigung der Haube an der Konstruktion + 8 zum Befestigen d
Montage - Bild 6-7-8 Die Abzugshaube ist mit Dübeln ausgestattet, die für die meisten Decken geeignet sind. Trotzdem sollte ein qualifizierter Techniker hinzugezogen werden, der entscheidet, ob die Materialien für die jeweilige Decke geeignet sind. Außerdem muß die Decke das Gewicht der Abzugshaube tragen können. Vor Ausführung des elektrischen Anschlusses den Hauptschalter der häuslichen Stromversorgung ausschalten. • Die gewünschte Länge des Traggerüstes der Abzugshaube einstellen.
3 4 273 4 4 4 244 4 4 6 6 273 190 7 14,5 5 6 214 9 7 7 8 8 7 7 2a 2a 2b 2b 12 10 11 10 10 10 11 Bild 6 17
• Bei Abluftbetrieb (13A) das andere Ende des Abluftrohrs an die häusliche Abluftvorrichtung anschließen. Bei Umluftbetrieb mit Aktivkohlefilter (13F) Umluftweiche F am Gitter montieren und mit vier Schrauben an der vorgesehenen Halterung befestigen. Zuletzt das Abluftrohr mit der Umluftweiche verbinden. • Die mitgelieferten Muttern mit Befestigungshaken (14) im Innern der oberen und unteren Kaminabschnitte auf Höhe der rechteckigen Ösen anbringen. Insgesamt müssen 10 Muttern montiert werden.
14 F 15 15 G 15 15 15 13F 15 H 16 15 15 15 16 13A 15 15 Bild 7 19
18 18 18 18 18 18 18 18 18 18 17 M 17 X 19 19 Bild 8 20 20 20 X
Geachte klant, Lees deze informatie aandachtig door. Lees vooral het hoofdstuk “Veiligheid” op de eerste pagina’s. Bewaar dit boekje goed, zodat u nog eens iets kunt nalezen. Geef het door aan een eventuele volgende eigenaar van het apparaat. • Bij technische problemen kunt u altijd contact opnemen met de AEG service-afdeling, zie hoofdstuk “Klantenservice”.
Inhoud Veiligheidsaanwijzingen ............................................................... 23 voor de gebruiker ............................................................................... 23 voor de keukenmeubel-monteur ......................................................... 23 Algemeen ........................................................................................ 25 Gebruik als afzuigkap ........................................................................
Veiligheidsaanwijzingen voor de gebruiker • U dient erop te letten dat op ingeschakelde kookzones en gasbranders altijd een pan staat, opdat het apparaat niet door te sterke hitte-ontwikkeling wordt beschadigd. Bij olie-, gas- en kolenfornuizen dient open vuur beslist te worden vermeden. • Bovendien moet bij het frituren op een fornuis of kookplaat de frituurpan tijdens het gebruik altijd in het oog worden gehouden. • De olie in de frituurpan kan door oververhitting vlam vatten.
• • • • • • • • 24 afvoer van rook-/verbrandingsgassen of een schacht die dient voor de ontluchting van ruimten met stookplaatsen geleid worden. Voor het afvoeren van de afgewerkte lucht moeten de plaatselijke voorschriften in acht genomen worden. Bij gebruik als afzuigkap moet gezorgd worden voor een voldoende grote toevoeropening, die ongeveer even groot als de afvoeropening moet zijn.
Algemeen • Het apparaat wordt als afzuigkap geleverd en kan in combinatie met een koolfilter (extra leverbaar accessoire) als recirculatiekap worden gebruikt. • Daarvoor is een origineel koolfilter nodig (zie “Extra leverbare accessoires”). • Alleen voor HI 8610: De kap is al uitgerust met een koolfiter. Verwijder dit filter als u de kap als recirculatiekap gaat gebruiken. Gebruik als afzuigkap • De lucht wordt met behulp van een op de afvoeropening A aan te brengen A buis naar buiten afgevoerd afb. 1.
Bediening van de afzuigkap • De afzuigkap is voorzien van een motor met regelbaar toerental. Het verdient aanbeveling de afzuigkap enkele minuten voor u met koken begint aan te zetten en hem na het koken nog ongeveer 15 minuten aan te laten staan.
Controle-inrichting voor vet- en koolfilters Deze afzuigkap beschikt over een inrichting die aangeeft wanneer de vetfilters gereinigd resp. het koolfilter vervangen moet worden (bij gebruik als recirculatiekap met koolfilter). Deze kap wordt door de fabriek zonder koolfilter geleverd, daarom is de verzadigingsindicatie voor het koolfiter uitgeschakeld.
Onderhoud • Voordat u werkzaamheden aan het apparaat gaat uitvoeren, eerst de stekker uit het stopcontact trekken. Metalen vetfilters • De metalen vetfilters hebben de taak om de vetdeeltjes die bij het koken ontstaan, op te zuigen en worden altijd, d.w.z. zowel bij gebruik als afzuigkap als bij gebruik als recirculatiekap, gebruikt. De metalen vetfilters moeten elke 4 weken worden gedemonteerd en in de afwasautomaat of met de hand worden schoongemaakt.
Koolfilter • Het koolfilter moet worden gebruikt, als het apparaat als recirculatiekap wordt gebruikt. • Daarvoor is een origineel koolfilter nodig (zie “Extra leverbare accessoires”). • Reinigen/vervangen van het koolfilter In tegenstelling tot andere koolfilters kan het LONG LIFE koolfilter gereinigd en gereactiveerd worden. Bij normaal gebruik van de kap moet het filter eens per twee maanden worden gereinigd (voor een gemiddeld gebruik van de kap van 2,5 uur per dag).
Attentie • Als u deze aanwijzingen m.b.t. reiniging van het apparaat en vervanging resp. reiniging van de filters niet opvolgt, kan dat tot brand leiden. Deze aanwijzingen beslist opvolgen! • De fabrikant is niet aansprakelijk voor schade aan de motor of schade t.g.v. brand die het gevolg zijn van ondeskundig onderhoud of niet opvolgen van de bovengenoemde veiligheidsvoorschriften. Vervangen van de lamp(en) • Stekker uit het stopcontact trekken. • Afdekkapje van de lamp m.b.v.
Klantenservice Geef in geval van storing onze service-afdeling onderstaande gegevens door: 1. modelaanduiding 2. E-nummer 3. F-nummer Deze gegevens vindt u op het typeplaatje op de binnenzijde van de afzuigkap, achter de vetfilters. Constructie- en kleurwijzigingen in het kader van de technische ontwikkeling voorbehouden.
Technische gegevens Afmetingen (in cm): Hoogte: Breedte: Diepte: Totale aansluitwaarde: Vent.
Montage - afb. 6-7-8 De wasemkap is voorzien van bevestigingspluggen die geschikt zijn voor de meeste plafonds. Er moet echter contact opgenomen worden met een gekwalificeerd technicus om u ervan te vergewissen dat de materialen geschikt zijn voor het type plafond. Het plafond moet stevig genoeg zijn om het gewicht van de kap te houden. Sluit het elektriciteitsnet in de schakelkast in uw woning af tijdens de elektrische aansluiting. • Stel de maat van de draagstructuur van de kap in.
3 4 273 4 4 4 244 4 4 6 6 273 190 7 14,5 5 6 214 9 7 7 8 8 7 7 2a 2a 2b 2b 12 10 11 afb.
• Bij gebruik als afzuigkap (13A) het andere eind van de afvoerbuis aan de afvoerinstallatie in de woning aansluiten. Bij gebruik met koofilter (13F) luchtgeleider F aan het rooster monteren en met vier schroeven aan de daarvoor bedoelde houder bevestigen. Ten slotte de afvoerbuis met de luchtgeleider verbinden. • De meegeleverde moeren met bevestigingshaken (14) binnenin de bovenste en onderste schouwdelen ter hoogte van de rechthoekige ogen aanbrengen. In totaal moeten tien moeren worden gemonteerd.
14 F 15 15 G 15 15 15 13F 15 H 16 15 15 15 16 13A 15 15 afb.
18 18 18 18 18 18 18 18 18 18 17 M 17 X 19 20 X 20 19 afb.
Pour les appareils commercialises par la France Lors de sa fabrication, cet appareil a été construit selon des normes, directives et/ou décrets pour une utilisation sur le territoire français. Pour la sécurité des biens et des personnes ainsi que pour le respect de l’environnement, vous devez d’abord lire impérativement les préconisations suivantes avant toute utilisation de votre appareil.
Chère cliente, cher client, Veuillez lire attentivement cette notice d’utilisation et notamment le chapitre « Sécurité » que vous trouverez dans les premières pages. Conservez cette notice d’utilisation pour pouvoir la consulter ultérieurement. Transmettez-la à l'éventuel prochain propriétaire de l’appareil. Mise au rebut Mettre au rebut les matériaux d'emballage • Tous les emballages sont recyclables, les films et les mousses sont marqués en conséquence.
Sommaire Consignes de sécurité .................................................................... 41 pour l’utilisateur ................................................................................. 41 pour l’installateur ............................................................................... 42 Généralités ...................................................................................... 44 Version évacuation extérieure ............................................................
Cet appareil doit être installé par une personne qualifiée et selon les normes en vigueur. Consignes de sécurité pour l’utilisateur • Il est recommandé de ne jamais laisser les foyers de cuisson sans récipient dessus. En cas de cuisinières à gaz, à mazout ou à charbon il faut absolument éviter toute flamme libre. • Par ailleurs, en cas de friture il faut faire attention à la friteuse placée sur le plan de cuisson. En effet l’huile pourrait prendre feu à cause d’une surchauffe.
Cet appareil porte le symbole du recyclage conformément à la Directive Européenne 2002/96/CE concernant les Déchets d’Équipements Électriques et Électroniques (DEEE ou WEEE). En procédant correctement à la mise au rebut de cet appareil, vous contribuerez à empêcher toute conséquence nuisible pour l’environnement et la santé de l’homme. présent sur l’appareil ou sur la documentation qui Le symbole l’accompagne indique que ce produit ne peut en aucun cas être traité comme déchet ménager.
électricien qualifié. • Le conduit d'évacuation, quel qu'il soit, ne doit pas déboucher dans les combles. • Dans le cas où l'appareil est relié directement à l'installation électrique, interposez un interrupteur bipolaire ayant une distance d'ouverture des contacts d'au moins 3 mm.
Généralités • La hotte est livrée en version évacuation mais peut, grâce à l’emploi d’un filtre à charbon actif (en option), être utilisée en version recyclage. • Pour cela, il faudra vous procurer le filtre à charbon actif d’origine (voir Accessoires). • Seulement pour HI 8610: La hotte est déjà fournie avec le filtre à charbon actif. Pour utiliser la hotte en version évacuation extérieure enlevez le filtre à charbon actif.
Utilisation de la hotte • La hotte aspirante est équipée de vitesse réglable. Il est conseillé de mettre en marche la hotte quelques minutes avant le début de la cuisson et de la laisser fonctionner env. une quinzaine de minutes après la cuisson afin d’éliminer toutes les odeurs. Le tableau de commandes de la hotte aspirante se trouve sur le devant de l’appareil: A B C D - E F G- H I - Interrupteur d’arrêt (OFF/Stand-by) Interrupteur de marche et sélection des vitesses 1-2-3-1-2-........
Dispositif de contrôle de saturation du filtre à graisse et du filtre à charbon actif Cette hotte à évacuation est équipée d’un dispositif signalant à l’usager quand il faut nettoyer le filtre à graisse et éventuellement le filtre à charbon actif. La hotte est fournie sans filtre à charbon actif; voilà pourquoi le dispositif signalant la saturation du filtre à charbon actif est débranché. La hotte doit être mise en “OFF” .
Entretien • Débranchez la hotte avant tout entretien. Filtre à graisse métallique • Le filtre à graisse métallique a pour but de piéger les particules de graisse produites durant la cuisson des aliments et est utilisé aussi bien durant le fonctionnement en version évacuation qu’en version recyclage. Le filtre à graisse métallique doit être extrait toutes les 4 semaines et lavé soit à la main, soit dans un lave-vaisselle.
Filtre à charbon • Le filtre à charbon est utilisé lorsque la hotte est utilisée en version recyclage. • Pour cela, il faudra utiliser le filtre à charbon actif d’origine (voir Accessoires). • Nettoyage/remplacement du filtre à charbon A la différence d’autres filtres de même type, le filtre à charbon LONG LIFE peut être nettoyé et réutilisé. Le filtre doit être nettoyé tous les deux mois en utilisation normale (en considérant une utilisation moyenne de 2,5 heures par jour).
Attention • Il y a risque d’incendie si vous ne respectez pas les instructions concernant le nettoyage de l’appareil et le remplacement ou le nettoyage du filtre. • La responsabilité du constructeur ne peut en aucun cas être engagée dans le cas d’un endommagement du moteur ou d’incendie liés à un entretien négligé ou au non respect des consignes de sécurité précédemment mentionnées. Remplacement de l´ampoule d’éclairage • Mettez la hotte hors tension.
Service Après-vente Dans le cas de demandes de renseignement ou de pannes, veuillez appeler notre service après-vente (voir la liste de nos différents points de service après-vente). Lors de l’appel, préciser : 1. La désignation du modèle 2. La référence 3. Le numéro de l’appareil Ces données sont indiquées sur la plaque signalétique située à l’intérieur de l’appareil et visible après ouverture de la grille du filtre à graisse.
Caractéristiques techniques Dimensions (en cm): Hauteur: Largeur: Profondeur: Puissance nominale totale: Moteur: Eclairage: Longueur du câble: Branchement électrique: 80-108 100 70 250 W 1 x 160 W 4 x 20 W 150 cm 220-240V Accessoires/Matériel de montage 1 multiraccord Ø 150-125 1 déflecteur + 6 vis 3,5x13 1 petite clé de fixation pour vis torx 6 vis 6 x 70 mm 6 goujons plugs Ø 10 mm 14 vis 4 x 7 mm + 14 écrous (pour fixer solidement les cheminées) 14vis 4 x 8 mm (6 pour fixer la hotte à la structure + 8 p
Branchement électrique Consignes de sécurité pour l’électricien Avant de brancher l’appareil, vérifier que la tension indiquée sur la plaque signalétique correspond à celle du secteur. Si l’appareil est muni d’une fiche de courant, il pourra être branché sur n’importe quelle prise de courant installée conformément aux normes et facile d’accès. Si un branchement permanent est nécessaire, la hotte devra être branchée par un électricien travaillant pour une entreprise d’électricité agréée.
Montage - Fig. 6-7-8 La hotte est équipée de chevilles de fixation convenant à la plupart des plafonds. Il est cependant nécessaire de s’adresser à un technicien qualifié afin de s’assurer que le matériel est approprié au type de plafond. Le plafond doit être suffisamment solide pour supporter le poids de la hotte. Durant les phases de branchement électrique, coupez le courant depuis le tableau principal de l’habitation.
3 4 273 4 4 4 244 4 4 6 6 273 190 7 14,5 5 6 214 9 7 7 8 8 7 7 2a 2a 2b 2b 12 10 11 Fig.
• En cas de fonctionnement en version aspirante (13A), raccordez l’autre extrémité du tuyau d’évacuation au dispositif d’évacuation de l’habitation. En cas de fonctionnement en version filtrante (13F), montez le déflecteur F sur la structure et fixez-le à la bride prévue à cet effet à l’aide de 2 vis puis raccordez le tuyau d’évacuation à la bague de raccordement située sur le déflecteur.
14 F 15 15 G 15 15 15 13F 15 H 16 15 15 15 16 13A 15 15 Fig.
18 18 18 18 18 18 18 18 18 18 17 M 17 X 19 20 X 20 19 Fig.
Contents Safety warnings .............................................................................. 59 For the user ...................................................................................... 59 For the installer ................................................................................. 60 Description of the Appliance ......................................................... 62 Extraction mode ................................................................................
Safety warnings For the user • The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. • Always cover lighted elements, to prevent excess heat from damaging the appliance. In the case of oil, gas and coal fired cookers it is essential to avoid open flames. • Also, when frying, keep the deep frying pan on the cooker top/cooker under careful control. • The hot oil in the frying pan might ignite due to overheating.
For the installer • When used as an extractor unit, the hood must be fitted with a hose having preferably the same diameter as the outlet hole. Attention: The hose is not supplied and must be purchased separately. Should there already be a pipe of diameter 125 mm that ducts to the outside through the walls or roof, it is possible to use the 150/125 mm reduction flange provided. In this case the hood will be slightly noisier.
• If the hood is used in its recirculation mode, it will operate simply and safely in the above conditions without the need for any of the aforementioned measures. • When the hood is used in its extraction mode, the following rules must be followed to obtain optimal operation: - short and straight outlet hose - keep bends in outlet hose to a minimum - never install the hoses with an acute angle, they must always follow a gentle curve.
Description of the Appliance • The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. • The hood is supplied as an extractor unit and can also be used with a recirculation mode by fitting a charcoal filter. • Only for HI 8610: The cooker hood is supplied ready for use as a recirculation hood and may be used for extraction by removing the charcoal filter which has been fitted inside the cooker hood.
Hood Operation • Best results are obtained by using a low speed for normal conditions and a high speed when odours are more concentrated. Turn the hood on a few minutes before you start cooking, you will then get an under pressure in the kitchen. The hood should be left on after cooking for about 15 minutes or until all the odours have disappeared. The control switches are located on the unit’s front panel: A B C D E - F G - H I - Fig. 2 Main switch, hood off (OFF-stand-by).
Control device for grease and charcoal filters This hood is fitted with a device that signals when it is necessary to clean the grease filter or the charcoal filter (in the case of recirculation version with charcoal filter). On delivery, the hood is not supplied with an charcoal filter, so the saturation indicator will be disabled. If the hood is to be used with a charcoal filter, the saturation indicator light must be enabled as follows: Set "OFF" the hood.
Maintenance and Care • The hood must always be disconnected from the electricity supply before beginning any maintenance work. Cleaning the hood • Clean the outside of the hood using a damp cloth and a solution of water and mild washing up liquid. • Never use corrosive, abrasive or flammable cleaning products or products containing bleach. . • Never insert pointed objects in the motor’s protective grid. • Only ever clean the switch panel and filter grill using a damp cloth and mild washing up liquid.
Charcoal filter • The charcoal filter should only be used if you want to use the hood in recirculation mode. • To do this you will need an original charcoal filter (available from your local Service Force Centre). • Cleaning/replacing the charcoal filter Unlike other charcoal filters, the LONGLIFE charcoal filter can be cleaned and reactivated. With normal use the filter should be cleaned every second month (when using the hood 2,5 hours per day,on avarage).
Warning • Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. • The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations. Changing the light bulbs • Disconnect the cooker hood from the mains supply.
What to do if If your appliance fails to work properly please carry out the following checks. Symptom Solution The cooker hood will not start... Check that: The hood is connected to the electricity supply. Check that a fan speed has been selected The cooker hood is not working Check that: The fan speed is set high enough for the task. The grease filters are clean. The kitchen is adequately vented to allow the entry of fresh air.
Technical assistance service (not for UK) You are welcome to telephone our technical assistance service (see list of technical assistance centres) whenever you need information or in the unlikely event of a fault. For service in Australia call 1300 650 020. When calling, please be ready to specify: 1. The model code number 2. The serial number (E-Nr.) 3. The manufacturing number (F-Nr.) This information is shown on the registration plate inside the unit behind the grease filter.
CUSTOMER CARE DEPARTMENT For general enquiries concerning your AEG appliance or for further information on AEG products, please contact our Customer Care Department by letter or telephone at the address below or visit our website at www.aeg.co.uk Customer Services Department Major Appliances AEGElectrolux Addington Way Luton Bedfordshire LU4 9QQ 08705 350 350 (*) * calls to this number may be recorded for training purposes.
Electrical connection (not for UK) Safety warnings for the electrician Before connecting the appliance to the power supply, check that the voltage indicated on the rating plate corresponds to the mains power supply available. Appliances fitted with a plug can be connected to any standard power socket within easy access. Should it be necessary to provide a fixed connection, the hood must only be installed by an electrician authorised by the local electricity board.
Installation - Fig. 6-7-8 Expansion plugs are provided to secure the hood to most types of ceilings. However, a qualified technician must verify suitability of the materials in accordance with the type of ceiling. The ceiling must be strong enough to take the weight of the hood. During electrical connection ensure the power supply is disconnected at the domestic mains switch.
3 4 273 4 4 4 244 4 4 6 6 273 190 7 14,5 5 6 214 9 7 7 8 8 7 7 2a 2a 2b 2b 12 10 Fig.
• For extractor versions (13A), connect the other end of the exhaust pipe to the flue. For filter versions (13F), fit deflector F to the support and secure it to the bracket supplied using 4 screws, then connect the exhaust pipe to the connection ring located on the deflector. • Fit the nuts with fixing hooks (14) supplied inside the top and bottom sections of the flues at the rectangular slots. A total of 14 nuts must be fitted.
14 F 15 15 G 15 15 15 13F 15 H 16 15 15 15 16 13A 15 15 Fig.
18 18 18 18 18 18 18 18 18 18 17 M 17 X 19 19 Fig.
From the Electrolux Group. The world´s No.1 choice. The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines,vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world. AEGElectrolux Addington Way Luton Bedfordshire LU4 9QQ http://www.aeg.co.