R ADV25 8.
Important Notice An LCD panel and / or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation. If the LCD panel or video monitor is used for television reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only function when the vehicle is in “park” or when the vehicle’s parking brake is applied.
MATERIALS INCLUDED IN THIS PACKAGE: 1) 2) 3) 4) 5) ADV25 TV / Video Monitor with DVD – (1pc) 12 Pin Power / Signal harness (P/N 112-3483) – (1pc) 2 Pin Power Wire Harness with choke (P/N 112B3143) – (1pc) 9 Pin ~ 3 RCA Jack Pigtail (P/N 112-3682) – (1pc) Hardware Package #4 x 5/16 Self Tapping Screws – (1pc) #4 x 7/16 Self Tapping Screws – (3pcs) Screws ISO 3 x 8mm Long – (5pcs) #8 x 3/8" Self Drilling Screws – (4pcs) M5 Screws (4pcs) 6) Trim Ring (Shale) – (1pc), Pewter – (1pc) 7) Remote Control (P/N 136-
Installing The Snap On Covers 1. 2. 3. Snap On Cover (Shroud) 1 Pewter, 1 Shale Housing 4. Snap On Cover (Screen Back Cab) 1 Pewter, 1 Shale Pry Tool Place the pod on a soft surface to avoid damaging the plastic. Installing The Shroud catch catch (A) Begin by hooking area “A” (above) over the dome light and slide the cover over the pod. The cover will snap in place. Installing The Screen Cover (B) (B) Open the screen and hook the two tabs “B” on the bottom edge of the screen.
Removing The Snap On Cover (Shroud) From The Housing Work on a soft surface to avoid damaging the plastic. Insert the supplied pry tool between the Housing and Snap On Cover (Shroud), then press the pry tool to release the Snap On Cover (Shroud). 1 2 3 Removing The Snap On Cover (Screen Back) From LCD The Housing Insert the supplied pry tool between the Housing and Snap On Cover (Screen Back), then press the pry tool to release the Snap On Cover (Screen Back).
GENERAL INSTALLATION APPROACH: 1) Decide upon system configuration and options that will be installed (i.e.: what components, VCP, Video Game, external amp, wireless headphones, VCP, etc.). 2) Review all manuals to become familiar with electrical requirements and hook ups. 3) Decide upon mounting locations of all components and method of mounting.
GENERAL SYSTEM CONFIGURATIONS: The following is intended to provide some of the system configurations that are possible with the ADV25 Drop Down Video Systems: The ADV25 has an option that allows the user to select from two IR transmit and receive codes (M1 or M2). This feature can be used when using two ADV25s in the same installation or if the vehicle has an RSA (Rear Seat Audio) that uses an “A” channel headset. The ADV25 comes factory set to M1.
TRIM RING INSTALLATION: Note: This page only covers special installation considerations for thick trim ring installation. If the video monitor is to be installed in a vehicle with the thick trim ring, it may need to be trimmed to fit the contour of the vehicle Headliner. Note: The trim rings supplied with this unit are not designed to be trimmed. 1) In this installation, the video monitor is mounted directly to the overhead cross-member in the roof using the mounting screw bosses.
TRIM RING INSTALLATION: Supplied screws as below use for install Trim Ring to unit. Please refer illustration below.
MOUNTING THE TRIM RING Roof Roof Support Headliner Mounting Bracket Self-drilling Screws Trim Ring Video Unit M5 Screw 8
ADV25 1) Make the connections to the vehicle for the 12 pin wiring harness. 2) Connect power harness to vehicle’s electrical system by tapping into an accessory hot line and a good ground. 3) Connect the 12 pin harness to the mating connector on the Video Monitor. 4) If an auxiliary video input is used (VCP, DVD, etc) insert the Circular Mini-Din Connector of the source component harness through the wire tie loop on the main PCB and into the Mini-Din Connector on the main PCB.
ADV25 AV2 ® TV Antenna (AN-400) (Optional) To TV Antenna In 9 Pin ~ 3 RCA Jack Pigtail * Optional Relay Box SIRSWB *** Optional PODTVT2 (See TV Tuner Note on previous page) PODTVT2 DIN 1 * Antenna for Wireless FM Mod. ** See Antenna Note on the previous page 12 Pin Power / Signal harness Accessory Harness - Optional (P/N:8010730) Red RCA (Audio Right) White RCA (Audio Left) Yellow RCA (Video) Power Connector 4 Pin Clean the IR Receiver Window on the front of the VCP.
CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle's wiring. There are two common types of dome light circuits used, positive or negative switched. Positive systems supply voltage to the interior lights to turn them on, negative switched systems apply ground to illuminate the bulbs. To determine which system you have you must locate the wires at the dome light.
Negative Switched Dome Lighting To 12 pin connector Red / black - Lamp on Black / red - Lamp common Purple / brown - Lamp Auto To constant To constant Factory Door ajar switch or Body Control computer Troubleshooting: SYMPTOM: REMEDY: No power at Video Monitor Verify +12 VDC on Red wire at 2 pin Power Harness behind video monitor.
128-7641 © 2006 ADVENT, 150 Marcus Blvd.
