Semi-Rugged Tablet PC S10A User Manual Ver 1.
S10A User Manual Table of Contents Preface ................................................................ i CE Conformity Statement .............................................. i FCC Compliance Statement ........................................... ii Copyright Statement ...................................................iii Safety Instructions ................................................. iv Battery Safety ............................................................v RTC Battery Caution ..........
S10A User Manual Installing a Scanner (optional) ....................................... 14 Upgrading Components........................................... 15 Removing the Memory ................................................ 15 Replacing the Memory ................................................ 15 Removing the Hard Disk Drive ....................................... 16 Replacing the Hard Disk Drive ....................................... 17 Removing the Battery .........................................
S10A User Manual Systems Requirements ................................................ 38 Installation Wizard..................................................... 38 How to Open the Fingerprint Software Menu...................... 41 Verify Your Fingerprint ............................................ 41 IE Auto Login ........................................................... 42 How to “Save Username and Password” ........................ 42 IE Auto Login Auto-Filling .......................................
S10A User Manual Recovering from a System Crash (Windows XP Embedded) ..... 63 Appendix ............................................................ 65 Specifications........................................................... 65 Optional Accessories .................................................. 68 External Battery .................................................... 68 Tablet PC Docking.................................................. 69 Adjustable Stand ..............................................
S10A User Manual Preface CE Conformity Statement Radio products with the CE alert marking comply with the R&TTE Directive (1999/5/EC) issued by the Commission of the European Community. Compliance with this directive implies conformity to the following European Norms (in brackets are the equivalent international standards).
S10A User Manual FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference; 2. This device must accept any interference received, including interference that may cause undesired operation. CAUTION! Exposure to Radio Frequency Radiation. The radiated output of this device is far below the FCC radio frequency exposure limits.
S10A User Manual interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected • Consult the dealer or an experienced computer technician for help Copyr
S10A User Manual Safety Instructions Use the following safety guidelines to help protect yourself and S10A. • Do not attempt to service the S10A yourself. Always follow installation instructions closely. • Be sure that nothing rests on the AC adapter's power cable and that the cable is not located where it can be tripped over or stepped on. • Do not cover the AC adaptor with papers or other items that will reduce cooling; also, do not use the AC adapter while it is inside a carrying case.
S10A User Manual Battery Safety RTC Battery Caution RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. • Do not place the battery incorrectly as this may cause danger of explosion. • Dispose of used batteries according to the manufacturer's instructions. • Do not dispose of batteries in a fire. They may explode. Check with local authorities for disposal instructions.
S10A User Manual Storage and Safety Notice Although charge Lithium-Ion batteries may be left unused for several months, their capacity may be depleted due to the build up of internal resistance. If this happens they will require recharging prior to use. Lithium-Ion batteries may be stored at temperatures between -20°C to 50°C, however they may be depleted more rapidly at the high end of this range. It is recommended to store batteries within normal room temperature ranges.
S10A User Manual Rugged and Ready to Go Congratulations on your purchase of the S10A Semi-Rugged Tablet PC. This product combines rugged design with reliable performance and powerful functionality to best suit all your needs, in a wide range of working conditions. This user manual outlines all you need to know to set up and use your S10A. If you have any further questions or queries, contact our technical support team via our website: www.aca-digital.com.
S10A User Manual Package Contents Ensure all the following items are present when you receive your S10A. If any of these items are missing, contact your vendor immediately. Note • • • • • • Screens used in this manual are for illustrative purposes only. Actual screens may vary depending on your product version.
S10A User Manual Exploring the S10A Front View 1 2 3 5 4 S1 S2 7 6 7 8 F1 9 No. 3 F2 10 F3 MODE ENTER 11 12 13 14 9 Component 1 Power LED • Off: Power off • Solid green: Power on / When in power off mode, lights green when charging. • Blinking green: AC power on and the battery is charging 2 HDD LED • Lights green to indicate hard disk drive activity.
S10A User Manual No. Component 5 S1 / Brightness button • Functions as a barcode switch key when a barcode scanner is connected, otherwise, can be assigned as a function key (F4). • When mode is enabled, press to decrease brightness. 6 S2 / Brightness button • Can be assigned as a function key (F5). • When mode is enabeld, press to increase brightness.
S10A User Manual Rear View 2 1 3 4 5 Lock Lock 5 6 No.
Right View 1 2 3 No. 4 Component 1 Microphone jack 2 Headphone jack 3 VGA port 4 Serial port Left View 1 No.
S10A User Manual Bottom View 1 7 No.
S10A User Manual Getting Started Installing the Rubber Bumpers To protect the housing case of S10A, install the rubber bumpers. 1. Install the rubber bumpers on the left and right side of S10A. 2. Make sure the rubber bumpers are aligned and locked on the indents. S1 S2 F1 F2 F3 MODE ENTER Removing the Rubber Bumpers From the rear of the tablet PC, remove the rubber bumpers.
S10A User Manual Inserting a Memory Card You can insert an SD card to store data, which needs to be later transferred to another machine, or to simply expand the storage capacity of the S10A. You can use SD cards up to 8GB in size. 1. Open the SD card compartment cover. DC IN 2. Insert the SD card with the metal contacts facing upwards, until it clicks into place. DC IN 3. Close the memory card compartment cover.
S10A User Manual Removing a Memory Card 1. Open the SD card compartment cover. DC IN 2. Press the SD card inwards to eject it from the slot. DC IN 3. Remove the card and close the SD card compartment cover.
S10A User Manual Installing a GPRS Module (optional) 1. Make sure the system is turned off. Unscrew the middle compartment cover. 2. Align and insert the connector of the GPRS module with the connector in the compartment. 3. Remove the adhesive cover of the antenna. 4. Tape the adhesive at the back of middle compartment cover to secure the antenna. 5. Screw to secure the GPRS module inside the compartment.
S10A User Manual 6. Push the SIM card into the slot, with the metallic part facing up and the clipped corner facing inward, until it clicks into place. 7. Screw the middle compartment cover. Note To use the GPRS function, you need to setup and activate the ethernet adapter. See “GPRS Connection (optional)” on page 35. Removing 3G SIM Card (optional) Slightly push the SIM Card inwards to pop it out.
S10A User Manual Installing an MSR (optional) 1. Make sure the system is turned off. 2. Unscrew the right compartment cover to remove. 3. Attach the MSR connector to the connectors inside the compartment. 4. Screw to secure the MSR module onto the tablet PC.
S10A User Manual Installing a Scanner (optional) The 1D or 2D barcode scanner module comes with a 2M CCD camera. 1. Make sure the system is turned off. 2. Unscrew the left compartment cover. 3. Remove the camera connector. 4. Attach the scanner connector to the connector inside the compartment. 5. Screw to secure the scanner module onto the tablet PC.
S10A User Manual Upgrading Components Removing the Memory 1. Make sure the system is turned off. 2. Move the power switch to the left to ensure battery power is completely cut off. See “Using the Power Switch” on page 8. 3. Unscrew the memory compartment cover. SW1 Lock Lock Lock Lock 4. Release the retaining clips to eject the memory from the socket. Replacing the Memory 1. Gently push new memory into the socket until the retaining clips click into place.
S10A User Manual 2. Screw the memory compartment cover back. Lock Lock Removing the Hard Disk Drive S10A comes with an 80G PATA hard disk drive. If more space is required for your application or there is a need to transport the hard disk content, follow the steps below to remove the hard disk drive. 1. Make sure the system is turned off. 2. Move the power switch to the left to ensure battery power is completely cut off. See “Using the Power Switch” on page 8. 3. Unscrew the left compartment cover.
S10A User Manual Replacing the Hard Disk Drive 1. Insert the hard disk into the slot with the connector facing down. 2. Connect the hard disk connector. 3. Screw the left compartment cover back. Removing the Battery 1. Make sure the system is turned off. 2. Move the power switch to the left to ensure battery power is completely cut off. See “Using the Power Switch” on page 8. SW1 3. Unscrew the battery compartment cover. Lock Lock Lock Lock 4. Remove the battery connector. 5.
S10A User Manual Replacing the Battery 1. Connect the battery connector to the connector inside the compartment. 2. Place the battery inside the compartment. Lock Lock Lock Lock 3. Screw the battery compartment cover back.
S10A User Manual Making Connections Connecting the Power Before you can use your S10A, you must fully charge the battery. Connect the power adapter as shown and leave to charge for: • a minimum of 4 hours when using the internal battery • a minimum of 8 hours when a second battery is installed Connecting to a Monitor You can connect the S10A to an external monitor for enhanced viewing. Connect one end of a VGA cable to the VGA port on the right side of the S10A.
S10A User Manual Connecting USB Devices You can connect peripheral devices, such as a USB keyboard and mouse, as well as other wireless devices using the USB ports on the left side of the S10A. Connecting Headphones You can connect a pair of headphones using the headphone jack on the right side of the S10A. Connecting a Microphone The S10A features a built-in microphone, but you can still connect an external microphone if needed.
S10A User Manual Turning On 1. Move the power switch to the right. SW1 2. Press and hold the power button to turn on the S10A. SD DC IN Turning On for the First Time (If you are using Windows XP Professional Embedded) When you first turn on the S10A, the following setup screens will appear. Follow these instructions to validate your version of Windows XP and set up your system correctly. 1. The Welcome screen appears. Tap Next to continue. 2. Tap Yes, I accept to agree to the terms and conditions.
S10A User Manual 3. Enter the 25-digit product key to validate your copy of Windows. Tap Next to continue. 4. Enter a name to identify your S10A. This the name by which it will be recognized on all connected networks. You can also enter a description if required. Tap Next to continue. 5. Enter an administrator password and re-confirm. Tap Next to continue. 6. Choose whether or not to make the S10A part of a domain. If so, enter the domain name (ask your system administrator for details).
S10A User Manual 7. Choose whether or not to activate your copy of Windows immediately or at a later date (we recommend you activate the software immediately). Tap Next to continue. 8. You can now configure your internet connection. Tap Yes, help me connect to the Internet to run the Internet Configuration Wizard. Tap Next to continue. 9. Enter the names of other users of your S10A. You can add up to five users. Tap Next to continue. 10. Tap Finish to complete the setup.
S10A User Manual Controlling the S10A Using the Touch Screen The S10A is equipped with touch screen technology, for ease of use when you are on the go. Simply tap the screen with your finger to select icons and run applications. Using the Tap Function When you tap on the screen with the a pen or stylus, it emulates click functions of a regular mouse. • To emulate a left click single tap the screen once. • To emulate a right click tap and hold the screen. • To emulate a double click, tap the screen twice.
S10A User Manual 2. Tap the Calibrate tab and you will see two options: • Standard Calibration: select this option to start 5 points Standard Calibration. • Advanced Calibration: select this option to use 4, 9, 16, or 25 points to calibrate the screen. Check Plot calibration data to enable touch panel linearity comparison graph. The blue lines show linearity before calibration and black lines show linearity after calibration. 3. Touch the points as displayed onscreen using the pen.
S10A User Manual Using the Control Panel Buttons The control panel buttons are located on the front side of S10A. See below for a description of each button and its function. Button F1 F2 MODE ENTER S1 S2 Name F3 Function Function Press to access your favorite programs. Keyboard Press to access the on-screen keyboard. Mode Press to enable/disable mode. Enter Press to emulate the Enter key.
S10A User Manual Configuring the Function Buttons The F1, F2, F3, S1 (F4) and S2 (F5) can be configured as shortcuts to access your favorite or frequently used programs. 1. Press the function button to which you want to assign a program shortcut to. The function button screen appears. 2. Tap to locate the program on the hard drive. 3. To remove a configured program, tap . 4. Tap OK to save all new settings.
S10A User Manual Adjusting Screen Brightness 1. Ensure mode is enabled. 2. Press S1 to decrease brightness, or S2 to increase brightness. Adjusting the Volume 1. Tap the Volume icon on the system tray. 2. Move the slide to adjust volume.
S10A User Manual Wireless Connections WiFi Connection Note WiFi access requires a separate purchase of a service contract with a wireless service provider. Contact a wireless service provider for more information. The S10A comes pre-loaded with WLAN module, you can send and receive signals to a WiFi network then synchronize files. A wireless network can be added either when the network is detected or by manually entering settings information.
S10A User Manual 3. You are prompted to enter a WEP key for secure access. Contact the network administrator for this key. 4. Enter the required WEP key and reenter the key for confirmation and then tap Connect. 5. The wireless connection is negotiated and you see the following screen. The wireless connection icon in the notification area shows a connected status whenever a wireless connection is present.
S10A User Manual Configuring a New Wireless Network Should you need to configure a set of computers to create a new wireless network, do the following: 1. Tap the wireless icon in the Windows system tray to open the Wireless Network Connection Status screen. 2. Tap Set up a wireless network for a home or small office. The Wireless Network Setup Wizard begins. 3. Tap Next to continue setup. 4.
S10A User Manual Next to continue. (Skip to step 8 if you decide to configure each computer manually.) 6. Insert your USB flash drive into a free USB slot and select the drive name from the dropdown list.Tap Next to continue. 7. All your current network settings are copied to your USB flash disk. Tap Next to continue. 8. Setup is complete. Tap Print Network Settings to print a list of settings if you are configuring each computer manually. Tap Finish to complete the wizard. 9.
S10A User Manual Bluetooth Connections The S10A comes with built-in Bluetooth functionality that allows you to connect and communicate with other Bluetooth-enabled devices. Setting Up Bluetooth Follow these instructions to set up a Bluetooth connection. 1. Tap Start > Control Panel and double-tap Bluetooth Device Properties to open the Bluetooth Devices screen. 2. Tap Add to open the Add Bluetooth Device Wizard. 3. Select the My device is set up and ready to be found checkbox and tap Next.
S10A User Manual 4. The Wizard searches for and displays other Bluetooth devices within range. 5. Tap the device you want to connect to and tap Next. You are prompted for a passkey. 6. Select your option and tap Next. 7. The Wizard attempts to connect with the other device and prompts the other device to input the passkey. If the other device has successfully accepted the passkey, the devices are connected and the Wizard finishes.
S10A User Manual GPRS Connection (optional) GPRS function is optional with S10A. It allows you to make 3G connection to the internet. See “Installing a GPRS Module (optional)” on page 11 for installation instruction. Note Before setting up GPRS, obtain the access point (AP) from your SIM card’s network service provider. Setting Up GPRS 1. Tap Start > All Programs > Siemens > HSDPA USB Modem > Connection > Manager to run the software. 2. On Select Device, select Siemens Wireless Adapter.
S10A User Manual 3. Check APN Name, then enter the access point name of your network service provider on the space. In this case, “internet” is the AP name. 4. Tap Connect. 5. When connected, signal strength is shown on the lower left corner of the Connection Manager window. Note To avoid damage to the SIM card, insert the SIM card before you turn the power on and remove the SIM card after you turn the power off.
S10A User Manual GPS Connection (optional) GPS function comes optional with S10A. It allows you to view your GPS positions. The following illustration demonstrates how the GPS viewer operates. It is only an example. 1. From the Com Port drop down menu tap COM5 to select COM5 as your com port. 2. From the Baudrate drop down menu tap 4800 to select 4800 as your baudrate. 3. Tap Open GPS to start GPS. 4. When satellites are detected, their positions are shown on the map.
S10A User Manual Using the Fingerprint Software S10A comes with a fingerprint module. Read the following context to install and use the fingerprint software. Systems Requirements • Pentium IV or higher or other 100% compatible machines • Windows 2000 / XP / Vista • At least 256 MB of RAM or higher Installation Wizard 1. Click Next. 2. Read the License Agreement. Select “I accept the terms in the license agreement”, then click Next. 3. Select the installation path, then click Next.
S10A User Manual 4. Enter the required settings. Check “Use Windows Logon”, then click OK. 5. To register your fingerprints, click Next. 6. Click the finger you want to register. The selected finger will be highlighted, click Next to continue. 7. Place your finger on the sensor as shown on the boxed picture.
S10A User Manual 8. Continue removing and placing your finger until the Back button turns into Next, then click Next. 9. You can continue to register up to 10 fingers. Click the Continue to continue to register another finger. Note It is recommended to register at least 2 or more fingers in case your finger gets hurt. 10. Click Finish to finish the registation. The icon appears on the system tray.
S10A User Manual How to Open the Fingerprint Software Menu There is only one way to open the Menu for Fingerprint software. Verify Your Fingerprint 1. Click the Fingerprint Software tray icon and swipe your finger to verify your fingerprint. or press click Password to enter the correct password. 2. Or press Password and enter the correct password. 3. If the fingerprint verification succeeds, the menu for fingerprint software appears on screen.
S10A User Manual IE Auto Login IE Auto Login allows you to automate the entry of username and password on a web site. At first, you save your username and/or password for a web site. When you go to the web site, IE Auto Login fills in the dialog boxes automatically after a successful fingerprint or password verification. This application is for Internet Explorer only.
S10A User Manual 3. Click the icon on the taskbar of Internet Explorer and choose “Save username and password”. 4. Verify your fingerprint or password. 5. After verification succeeds, the username and/or password is saved.
S10A User Manual IE Auto Login Auto-Filling Method 1: Start Internet Explorer and go to the web site where you have saved your username and/or password. Verify your fingerprint or password when asked.
S10A User Manual Method 2: You can also go to the web site directly without starting Internet Explorer via the menu for Fingerprint Access. Click IE Auto Login and choose the web site you want to go to. Internet Explorer will automatically start and show the web site you have chosen. And your ID and/or password will automatically be filled in.
S10A User Manual Auto Login Database Manager You can delete ID and Password, and manage all the URLs you’ve already registered. Sending ID and Password Automatically If you choose the option, when you visit the web site, your ID and password will automatically be filled and auto login will be done. Secure Lock Secure Lock is installed in the Virtual Disk of Fingerprint Access.
S10A User Manual Secure Lock “Unlock Drive”: 1. Go to “Secure Lock” and select “Unlock Drive”. 2. When the Secure Lock is on the condition of “Unlock”, you can see the Virtual Disk Encrypt Disk (P:) in the Windows Explorer. Meanwhile, it acts as a virtual hard drive. Secure Lock “Lock”: 1. Go to “Secure Lock” and select “Lock”. 2. When the Secure Lock is on the condition of “Unmount”, the Virtual Disk in the Windows Explorer will disappear and cannot be used.
S10A User Manual 3. In the Resize window, there are two ways to change the capacity of the Virtual Disk. • One is to drag the scroll bar to the left/right to decide the size. • Another is to enter the capacity you would like to change. 4. After completing capacity change, a message box will pop up to indicate it is completed.
S10A User Manual 3. Moving files into an encrypted folder will cause those files to be automatically encrypted. When removing files from an encrypted folder to a non-encrypted area, “Fingerprint Authentication” dialog will ask you for your fingerprint, and the file will be decrypted. Folder Decryption: To decrypt encrypted files. 1. Right-click on the encrypted folder, and choose “Decrypt Folder” from the menu. 2. “Fingerprint Identification” dialog will ask you for your fingerprint. 3.
S10A User Manual File Security File Encryption: Your encrypted files can only be accessed by fingerprint (or password). 1. Point the cursor to the file you want to encrypt and rightclick. Choose “Encrypt File” from the menu. 2. When authentication is successful, the file will be encrypted. Encrypted files will have a lock on their icons. File Decryption: To decrypt encrypted files. 1. Point the cursor to the file you want to decrypt and rightclick. Choose “Decrypt File” from the menu. 2.
S10A User Manual 3. When authentication is successful, the file will be decrypted. 4. The icon of the decrypted file will have no lock and will go back to its normal appearance. User Settings Open “Menu for Fingerprint Software > User Settings”.
S10A User Manual Fingerprint Registration 1. Right-click on the tray icon and select Fingerprint Registration. 2. In the “Fingerprint Identification” windows, there are two ways to verify your fingerprint. Method 1. • Finger Identification: Verify your previously registered fingerprint. The green fingers show which fingers have been registered. Method 2. • Password: Click the “Password” button and enter your password if you want to use it instead of your fingerprint.
S10A User Manual Windows Logon Setting 1. Open “Menu for Fingerprint Software > User Settings”. 2. Set “Windows Logon Setting”. 3. Restart Windows, you must swipe your finger to logon. 4. If the fingerprint verification succeeds, you can logon Windows.
S10A User Manual Screen Saver Lock Setting Introduction When the “Screen Saver Lock” starts, only an authorized person can unlock the Screen Saver by verifying his/her fingerprint or password. The Screen Saver Lock makes your PC more secure. The main function of “Screen Saver Lock” is to disable the keyboard and the mouse. 1. Open “Menu for Fingerprint Software > User Settings > Screen Saver Lock Setting”. 2. It will open the “Screen Saver Lock” dialog.
S10A User Manual Quick Bar Auto Hiding Setting 1. Open “Menu for Fingerprint Software > User Settings > Quick Bar Auto Hiding Setting”. • Never hide Quick Bar: If you don’t want to hide the Quick Bar, please check this option. • Second: You can set the auto hiding time here. (Example: 5 seconds) Add Another User Account’s Fingerprint(s) 1. Login another user account through original password entered. 2. Click the fingerprint tray icon . 3. New fingerprint enroll will start.
S10A User Manual Uninstall There are two ways you can uninstall the software. • Click Windows Start > All Programs > Fingerprint Software > Uninstall. • Click Windows Start > Control Panel > Add or Remove Programs, choose “Remove Fingerprint Application” then click “Change/Remove”. The “Uninstallation Wizard” will start. 1. It will remove all of the files in the Fingerprint Software folder, click OK. 2. Verify your fingerprint. Swipe the correct fingerprint.
S10A User Manual 3. “Delete Fingerprint Software” and the following messages will appear. Click Yes to complete the uninstallation.
S10A User Manual Advanced Settings Configuring Touch Screen Function Tap the pointer device icon in the system tray then select the Tools tab > or tap Start > All Programs > PenMount Universal Driver > PenMount Control Panel to access PenMount Control Panel. Tap the tabs at the top of the screen to access the settings screens. The contents in each tab page may vary based upon the version of the operating system you are using.
S10A User Manual Checking Battery Status As it is likely you will be using your S10A when out and about, it is important that you monitor the battery status regularly, to ensure you do not run out of power at a critical moment. Double tap on the Power icon on the system tray to view detailed information. The battery screen appears: Tap on the battery icon for more detailed information. Note 59 #1 battery indicates the status of the internal battery.
S10A User Manual Power Options You can configure specific power options to best suit your needs and to get the most out of your battery. Tap on the Power icon in the system tray to view the power options menu. See below for a description of the settings for each power option.
S10A User Manual Maintenance Maintaining the Battery • Do not expose heat or attempt to disassemble the battery, and do not place the battery in water or in a fire. • Do not subject the battery to strong impact, such as a blow from a hammer, or stepping on or dropping it. • Do not puncture or disassemble the battery. • Do not attempt to open or service the battery. • Replace only with batteries designed specifically for this product. • Keep the battery out of reach of children.
S10A User Manual Troubleshooting Recovering from a System Crash (Windows XP Professional Embedded) In the unlikely event that your S10A should crash, do the following to re-boot your system if you are using Windows XP Professional Embedded. 1. Connect a USB keyboard to the USB port on your S10A. MOLEX F1 1 ` End Tab Caps Lock Shift Ctrl F2 @ F3 # 2 Q Z Alt R D X F5 % 5 E S A F4 $ 4 3 W F C F7 & 7 8 U H B F8 M > .
S10A User Manual Recovering from a System Crash (Windows XP Embedded) Note If you are using an SD card for data storage, your S10A will follow the recovery procedures to re-boot your system. If you are using Windows XP Embedded, follow these steps to perform a recovery procedure using a USB flash drive should your system crash: 1. Download the FORMATUPD.EXE file to your local drive (C:\). 2. Connect a USB flash drive to your computer. 63 3. Click Start > Run and type cmd in the command box. 4. Type cd\
S10A User Manual 13.Highlight Save & Exit Setup and press Enter. 14.Press Y to save and exit when the confirmation message appears. 15.The system will now enter recovery mode. Click OK twice to continue. 16. Once the process is complete, click Quit, remove the USB flash drive and the system will restart automatically.
S10A User Manual Appendix Specifications Feature 65 Description Operating System Windows XP Embedded/ Windows XP Professional Embedded Windows Vista Basic Processor Intel ATOM Z530 1.6G / Z510 1.1G Chipset US15W Memory One SO-DIMM DDRI 533 support up to 2GB Storage Compact Flash (CF) Memory Card (4G/8G) Display 10.
S10A User Manual Feature Description LED Status Indicators Power LED: Off: Power off Solid green: Lit when charging in power off mode, off when charging is complete Blinking green: Power on, battery is charging in power on mode Solid yellow: Power on, battery low Blinking yellow: Power on, battery critically low HDD LED: Green when HDD is being accessed WLAN LED: Off: No RF signal / No LAN connection Solid Green: WLAN activated Blinking Green: TX/RX transmission Other Components CCD Camera 2M Fingerpri
S10A User Manual Feature 67 Description Certification CE, FCC Optional Device / Accessories 1D / 2D Barcode Scanner MSR 1+2+3 track RFID 13.
S10A User Manual Optional Accessories External Battery You can use an external battery to extend the power of your tablet PC. Battery specification: 3800mA 3S2P Installing the External Battery 1. Remove the external battery contacts cover from the tablet PC (A). B 2. Insert the contacts cover on the external battery (B). A SW1 3. Align and insert the battery on the tablet PC (C). 4. Lock to secure the battery in place (D).
S10A User Manual Tablet PC Docking You can use the docking stand to dock the tablet PC when you are at your home or on your office desk. When docked, you can charge both the internal and external batteries or transfer data from your tablet PC to another PC. Attach the S10A to the docking stand as shown. To charge the external battery, attach the battery to the docking stand as shown below. Lock Lock DC19V Note 69 The external battery can also be charged when installed on the tablet PC.
S10A User Manual Docking Connectors See below for the rear view of the docking and a description of all ports and connectors. DC19V 1 No. Component 2 3 4 Function 1 LAN port Connect an RJ-45 cable to access LAN connection. 2 Serial port Connect a serial cable to connect to another PC. 3 USB ports Connect USB connectors to transfer data. 4 DC-IN Connect the AC adapter to charge the battery.
S10A User Manual Docking Specifications Feature 71 Description Product Name S10A Tablet PC Docking Model Number S10AC External I/O Interfaces One LAN port One RS-232 Two USB 2.0 host connectors One DC-in Power Adapter Universal AC 90V ~ 265V, 47~63Hz input; 19V, 3.
S10A User Manual Adjustable Stand You can use the adjustable stand to provide desk support when you are at home or in your office. ck Lo 1. Fasten four screws to attach the two stand brackets to your Tablet PC. 2. Fasten the four screws to attach the stand to the brackets. ck Lo Attaching the Adjustable Stand 3. Pull to adjust the stand to desirable angle.
S10A User Manual Handstrap and Shoulder Strap A detachable handstrap and shoulder strap are provided to carry your Tablet PC securely and safely. You can use the supplied handstrap and shoulder strap separately or together to carry the S10A when you are outside your home or office. Handstrap Shoulder Strap Screws When using the handstrap and shoulder strap separately: • Attach the handstrap to the rear of your tablet PC using the four short screws. Ensure the straps and the flap are securely attached.
S10A User Manual The handstrap makes it easy to carry the device on one hand. Lock Lock • Attach the shoulder strap to the rear of your tablet PC using two screws as shown.
S10A User Manual When using the handstrap and shoulder strap together: • Attach the handstrap to the rear of your tablet PC using the four screws. Then hook the shoulder strap as shown. Lock Lock Vesa Mount Vesa mount can be used with a variety of alternate mounting solutions such as wall mounts. • Install the vesa mount by screwing on the screws as shown.
4RF Exposure Information (SAR) This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg.