User Manual EKI-6233BN Industrial Wi-Fi Client
EKI-6233BN User Manual ii
Copyright The documentation and the software included with this product are copyrighted 2022 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Declaration of Conformity CE This product has passed the CE test for environmental specifications. Test conditions for passing included the equipment being operated within an industrial enclosure. In order to protect the product from being damaged by ESD (Electrostatic Discharge) and EMI leakage, we strongly recommend the use of CE-compliant industrial enclosure products.
Technical Support and Assistance 1. 2. Visit the Advantech web site at www.advantech.com/support where you can find the latest information about the product. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance.
Packing List Before setting up the system, check that the items listed below are included and in good condition. If any item does not accord with the table, please contact your dealer immediately. 1 x WiFi Client device 1 x DIN-Rail Mounting Bracket and Screws 1 x Wall-mounting Bracket 2 x Antennas Safety Instructions Read these safety instructions carefully. Keep this User Manual for later reference. This device is for indoor use only.
Safety Precaution - Static Electricity Static electricity can cause bodily harm or damage electronic devices. To avoid damage, keep static-sensitive devices in the static-protective packaging until the installation period. The following guidelines are also recommended: Wear a grounded wrist or ankle strap and use gloves to prevent direct contact to the device before servicing the device. Avoid nylon gloves or work clothes, which tend to build up a charge.
Contents Chapter Chapter 1 Introduction ......................................... 1 1.1 1.2 1.3 1.4 Overview ................................................................................................... 2 Features.................................................................................................... 2 Specifications............................................................................................ 3 Dimensions .................................................................
4.6 4.7 Chapter 5 5.1 5.2 5.3 4.5.4 Statistics...................................................................................... 48 4.5.5 Site Survey. ............................................................................. 48 4.5.6 Log .............................................................................................. 49 Alarm....................................................................................................... 49 4.6.1 Setting......................................
List of Figures Figure 1.1 Figure 2.1 Figure 2.2 Figure 2.3 Figure 2.4 Figure 2.5 Figure 2.6 Figure 2.7 Figure 2.8 Figure 2.9 Figure 2.10 Figure 2.11 Figure 2.12 Figure 2.13 Figure 2.14 Figure 2.15 Figure 2.16 Figure 2.17 Figure 2.18 Figure 2.19 Figure 3.1 Figure 3.2 Figure 3.3 Figure 3.4 Figure 3.5 Figure 3.6 Figure 3.7 Figure 3.8 Figure 3.9 Figure 3.10 Figure 3.11 Figure 3.12 Figure 3.13 Figure 3.14 Figure 3.15 Figure 3.16 Figure 4.1 Figure 4.2 Figure 4.3 Figure 4.4 Figure 4.5 Figure 4.6 Figure 4.
Figure 4.21 Figure 4.22 Figure 4.23 Figure 4.24 Figure 4.25 Figure 4.26 Figure 4.27 Figure 4.28 Figure 4.29 Figure 4.30 Figure 4.31 Figure 5.1 Figure 5.2 Figure 5.3 Alarm > Setting ............................................................................................................ 50 Alarm > Event .............................................................................................................. 51 Alarm > LogFile ..........................................................................
Chapter Introduction 1 1
1.1 Overview The EKI-6233BN client device allows data transmission from LAN interface via Wi-Fi wireless technology transmit to a network. Design with one Ethernet port and 802.11 a/b/g/n 2x2 MIMO supported. EKI-6233BN provides a quick, simple and costeffective way to deliver remote management and data accessibility to thousands of devices that cannot connect to a network. In addition, you can actively request data or issue commands from wireless LAN side.
1.3 Specifications Specifications Description Interface I/O Port Power Connector Enclosure Installation Dimensions (W x H x D) Weight IP Rating System LED Port LED RJ45 Terminal block Metal shell with solid mounting kits DIN-rail and wall mount 103 x 95 x 25 mm (4.06" x 3.74" x 0.
1.4 Dimensions The following view depicts the EKI-6233BN. 25.00 [0.98] 103.00 [4.06] 95.00 [3.74] 103.00 [4.06] Figure 1.
Chapter Getting Started 2 2
2.1 Hardware 2.1.1 Front View The following view shows the EKI-6233BN. 1 SYS P2 P1 2 WLAN 3 EKI-6233BN 1 Figure 2.1 EKI-6233BN Front View No. Item Description 1. 2. 3. Antenna connector Connector for antenna. System LED panel See “LED Indicators” on page 8 for further details. ETH port RJ45 ports x 1.
2.1.2 Rear View 1 Figure 2.2 Rear View No. Item Description 1. Mounting plate used for the installation to a standard DIN rail DIN-Rail mounting plate 2.1.3 Top View V2 - V2 + PWR2 P-Fail V1 - V1 + PWR1 1 Figure 2.3 Top View No. Item Description 1. 2.
2.1.4 LED Indicators 1 2 3 SYS P2 P1 4 5 WLAN RX 1 TX Figure 2.4 System LED Panel No. LED Name LED Color Description 1. Status 2. P2 3. P1 4.
2.2 Connecting Hardware 2.2.1 DIN Rail Mounting The DIN rail mount option is the quickest installation option. Additionally, it optimizes the use of rail space. The metal DIN rail kit is secured to the rear of the gateway. The device can be mounted onto a standard 35 mm (1.37”) x 7.5 mm (0.3”) height DIN rail. The devices can be mounted vertically or horizontally. Refer to the following guidelines for further information. Note! A corrosion-free mounting rail is advisable.
See the following figure for an illustration of a completed DIN installation procedure. 3. Figure 2.6 Correctly Installed DIN Rail Kit Grasp the bottom of the gateway and slightly rotate it upwards. If there is resistance, the gateway is correctly installed. Otherwise, re-attempt the installation process from the beginning. 2.2.1.2 Removing the DIN-Rail Mounting Kit 1. Ensure that power is removed from the gateway, and disconnect all cables and connectors from the front panel of the gateway. 2.
2.2.2 Wall-Mounting The wall mounting option provides better shock and vibration resistance than the DIN rail vertical mount. Note! When installing, make sure to allow for enough space to properly install the cabling. Before the device can be mounted on a wall, you will need to remove the DIN rail plate. 1. Rotate the device to view the rear side and locate the DIN mounting plate. 2. Remove the screws securing the DIN mounting plate to the rear side. 3. Remove the DIN mounting plate.
11. Insert the screws through the bracket and tighten to secure the device to the wall. 2 1 2 Figure 2.9 Wall Mount Installation 12. Once the device is installed on the wall connect the required cables. 2.2.3 Wireless Connection 1. Connect the antenna by screwing the antenna connectors in a clockwise direction. SYS SYS P2 P2 P1 P1 WLAN EKI-6233BN 2. Figure 2.10 Installing the Antenna Position the antenna for optimal signal strength.
Note! The location and position of the antenna is crucial for effective wireless connectivity SYS SYS P2 P2 P1 P1 WLAN EKI-6233BN Figure 2.11 Positioning the Antenna 2.2.4 Network Connection For RJ45 connectors, data-quality, twisted pair cabling (rated CAT5 or better) is recommended. The connector bodies on the RJ45 Ethernet ports are metallic and connected to the GND terminal. For best performance, use shielded cabling. Shielded cabling may be used to provide further protection.
2.2.5 Power Connection 2.2.5.1 Overview Warning! Power down and disconnect the power cord before servicing or wiring the gateway. Caution! Do not disconnect modules or cabling unless the power is first gatewayed off. The device only supports the voltage outlined in the type plate. Do not use any other power components except those specifically designated for the device. Caution! Disconnect the power cord before installation or cable wiring.
2.2.5.2 Considerations Take into consideration the following guidelines before wiring the device: The Terminal Block (CN1) is suitable for 12-48 AWG (3.31 - 0.205 mm2). Torque value 7 lb-in. The cross sectional area of the earthing conductors shall be at least 3.31 mm2. Calculate the maximum possible current for each power and common wire. Make sure the power draw is within limits of local electrical code regulations. For best practices, route wiring for power and devices on separate paths.
Electromagnetic Interference (EMI) affects the transmission performance of a device. By properly grounding the device to earth ground through a drain wire, you can setup the best possible noise immunity and emissions. Connection to Grounding Point Drain Wire with Lug Figure 2.14 Grounding Connection By connecting the ground terminal by drain wire to earth ground the gateway and chassis can be ground.
There are two power inputs for normal and redundant power configurations. The power input 2 is used for wiring a redundant power configuration. See the following for terminal block connector views. V2- V2+ PWR2 P-Fail V1- V1+ PWR1 Figure 2.16 Terminal Receptor: Power Input Contacts To wire the power inputs: Make sure the power is not connected to the gateway or the power converter before proceeding. 1. Loosen the screws securing terminal block to the terminal block receptor. 2.
8. Tighten the screws on the terminal block to secure it to the terminal block receptor. If there is no gap between the terminal block and the terminal receptor, the terminal block is seated correctly. Figure 2.19 Securing a Terminal Block to a Receptor 2.3 Reset Button Reset configuration to factory default: Press and hold Reset button for 10 seconds. System reboot: Press and hold Reset button for 2 seconds. Note! Do NOT power off the gateway when loading default settings.
Chapter 3 Utility Configuration 3
3.1 Installing the Configuration Utility Note! 1. 2. 3. 4. Microsoft.NET Framework version 2.0 or greater is required for this application. Insert the Advantech EKI Device Configuration Utility CD-ROM into the CDROM drive (whereas E:\ is the drive name of your CD-ROM) on the host PC. Use Windows explorer or the Windows Run command to execute the setup program, the path for the setup program on the CD-ROM is as follows: E:\EKI_Device_Configuration_Utility_v3.04.
5. The Software License Agreement displays, press I Agree to continue or Cancel to stop the installation. Figure 3.2 InstallShield Wizard 2 of 4 The InstallShield continues and a status screen displays. The default installation path is C:\Program Files\EKI Device Configuration Utility. Figure 3.
6. Once the installation of the package is finished a Configuration Utility Setup screen displays. Click Finish to conclude the process and exit the InstallShield Wizard. Figure 3.
3.2 Starting the Configuration Utility Advantech EKI-6233BN devices provide an easy-to-use utility to configure your device through an Ethernet connection. For secure administration, it can also restrict the access rights for configuration to only one host PC. With this secure function enabled, other PCs will not have permission for configuration. After the installation program on the Advantech IEDG Series Driver Utility CD-ROM is finished, the devices are ready for use and configuration.
3.3 Discovering Your Device 3.3.1 Auto Searching Advantech EKI Device Configuration Utility will automatically search all the EKI6233BN devices on the network and show them on the Device List Area of the utility. The utility provides an auto-search function to show your device(s) by simply executing the configuration utility program from the Start Menu. From here all devices on the same network domain will be searched and displayed on Device List Area.
Information”, and “Serial Port Information”. The serial port information frame displays the operation mode, status, and connected host IP. Figure 3.7 Selecting a Group Click on the “+” before the device name, and the utility will expand the interfaces on this device. Figure 3.8 Selecting a Device Click to enter the configuration page to change the setting. The configuration will be introduced on following sections. Figure 3.
3.4 Network Settings Prior to setting up the server’s IP address determine the IP address mode. There are four mode types available: Static IP: mode to assign a specific assigned address DHCP / AutoIP: mode to automatically assign IP addresses through a DHCP server BOOTP / AutoIP: mode to automatically assign an IP address through the configuration server DHCP/BOOTP/AutoIP: mode to automatically assign an IP address using a Bootstrap Protocol or DHCP server.
You can choose from four possible IP Configuration modes --- Static, DHCP, BOOTP, and DHCP/BOOTP. Figure 3.11 Network Settings Overview Item Description Static IP DHCP + Auto-IP Static IPUser defined IP address, Subnet Mask, and Default Gateway. DHCP Server assigned IP address, Subnet Mask, Default Gateway, and DNS. BOOTP Server assigned IP address. DHCP Server assigned IP address, Subnet Mask, Default Gateway, and DNS, or BOOTP Server assigned IP address.
3.5 Administrator Settings 3.5.1 Locate the Device When devices are connected to the network, identification of a specific serial device is possible through the Locate function. To locate the device: 1. From the device list frame, locate the desired device and right-click on it to display the settings menu. 2. Select Locate from the menu. Figure 3.12 Locate the Device The unit’s Status LED will turn solid amber and the buzzer will sound until you click Stop Locate.
3.5.2 Restore to Factory Default Settings The configuration utility provides the function to restore the device to factory default settings. Figure 3.13 Restore to Factory Default Settings The confirm message will display after clicking Restore to Factory Default Settings. If you really want to restore the serial device sever to factory default settings, please click Yes button to continue. Power off the device within ten seconds.
3.5.3 Resetting the Device The Reset Device is available to allow you to reset the device. The function disconnects both the ethernet and serial connections. The function also allows the device to save new configuration settings to flash memory. Once a new setting is changed, you can use the Save function to accept the changes. You will need to reset the device to save the settings to flash memory. To reset the device: 1. Right-click a desired device to display the settings menu. 2. Select Reset Device.
3.5.4 Add to Favorite The Add to Favorite function allows to easily map available devices to Favorite’s. By bookmarking specific devices, you can create quickly accessible shortcuts for existing critical devices from the vast pool of locally or remotely networked EKI6233BN devices. Figure 3.
3.5.5 Update Firmware Advantech continually upgrades its firmware to keep up with the ever-expanding world of computing. You can use the update firmware function in the utility to carry out the upgrade procedure. Please access Advantech’s website: http:// www.advantech.com to download the latest version of the firmware. Before updating the firmware, make sure that your host’s Network domain is as same as the device or the host can establish the TCP connection to the device. To update firmware: 1.
Chapter Web Interface 4 4
4.1 Overview EKI-6233BN device can be configured through a web interface. By using a standard web browser, the same procedure as with the Windows configuration utility can be used. In the browser’s address field, enter the IP Address of your EKI-6233BN device. The default IP setting is 10.0.0.1, but you should use the IP which you have previously assigned for this device. Once the IP is entered, you will be presented with the following windows.
4.2.2 Accessing the Web Page via Web Browser Once the device is installed and connected, power on the device. The following information guides you through the logging in process. 1. Launch your web browser on the PC. 2. In the browser’s address bar, type the device’s default IP address (LAN Interface 1: 10.0.0.1). The main menu is shown. 3. Enter the default user name and password (admin/admin). 4. Click Enter to continue and access the interface. 4.3 Overview To access this page, click System. Figure 4.
Item Description System Up Time System Platform Memory Total Available Displays the time since the last device reboot. Displays the model name of the device. Free Buffered Local Network Local IP Address Local Netmask MAC Address WAN Network WAN IP Address WAN Netmask WAN Default Gateway DNS1 DNS2 DHCP Leases DHCP Leases Displays the total amount of physical memory installed RAM in kiloBytes (kB) on the device. Displays the currently unused RAM in kiloBytes (kB) on the device.
When Network Mode is Static, the configuration settings display as follows. Figure 4.4 Network Settings > Wireless WAN >Network Mode > Static The following table describes the items in the previous figure. Item Description Network Mode Click the drop-down menu to select the mode type: Disable (default), Static, DHCP. IP Address Enter the WAN IP address given by your service provider. Subnet Mask Enter the WAN subnet mask given by your service provider.
4.4.1.1 Topology NB/PC 10.1.1.3 E th e rrn et 192.168.1.0/24 192.168.1.1 (Default GW) GW SYS SYS P2 P2 P1 P1 WLAN CA 33 36 -IK E eR tes 1 RX TX EKI-1361 De D vice A Device AP Mode 10.1.1.2 1.1.2 Switch Swi SYS P2 P1 WLAN CA Link/Active RX 1 TX 2 EKI-1362 PWR Status Reset LAN 1 2 Serial Rx Tx 1 2 3 4 5 6 7 33 36 -IK E eR t es Device D vice B De 8 Console Client nt Mode Enablee WWAN WWAN 10.1.1.5 LAN1 192.168.1.
Item Description Local Hostname Domain Name Network mode Enter the device name: up to 31 alphanumeric characters. Enter a string to specify the domain name for the interface. Click the drop-down menu to select the IP Address Setting mode: Static or DHCP. Enter a value to specify the IP address of the interface. The default is 10.0.0.1. Enter a value to specify the IP subnet mask for the interface. The default is 255.255.255.0. Enter a value to specify the default gateway for the interface.
4.4.2.2 DHCP/AutoIP Network Mode To access this page, click Network Settings > LAN. Figure 4.8 Network Settings > LAN > DHCP/AutoIP The following table describes the items in the previous figure. Item Description Local Hostname Domain Name Network mode Enter the device name: up to 31 alphanumeric characters. Enter a string to specify the domain name for the interface. Click the drop-down menu to select the IP Address Setting mode: Static or DHCP.
4.4.2.3 DHCP/BOOTP/AutoIP Network Mode To access this page, click Network Settings > LAN. Figure 4.9 Network Settings > LAN > DHCP/BOOTP/AutoIP The following table describes the items in the previous figure. Item Description Local Hostname Domain Name Network mode Enter the device name: up to 31 alphanumeric characters. Enter a string to specify the domain name for the interface. Click the drop-down menu to select the IP Address Setting mode: Static or DHCP.
4.4.2.4 BOOTP/AutoIP Network Mode To access this page, click Network Settings > LAN. Figure 4.10 Network Settings > LAN > BOOTP/AutoIP The following table describes the items in the previous figure. Item Description Local Hostname Domain Name Network mode Enter the device name: up to 31 alphanumeric characters. Enter a string to specify the domain name for the interface. Click the drop-down menu to select the IP Address Setting mode: Static or DHCP.
4.4.3 Forwarding 4.4.3.1 Port Forwarding Port forwarding, also known as port mapping, is only available when Wireless WAN mode is enabled. It allows for the application of network addresses (NAT) the redirection of a communication request from an address and port to a specified address while the packets traverse the firewall. The function are designed for networks hosting a specific server, such as a web server or mail server, on the private local network and behind the NAT firewall. NB/PC 214.12.22.
4.4.3.2 DMZ A Demilitarized Zone is used to provide Internet services without sacrificing unauthorized access to its local private network. Typically, the DMZ host contains devices accessible to the Internet traffic, such as Web (HTTP) servers, FTP servers, SMTP (e-mail) servers and DNS servers. To access this page, click Networking > Forwarding > DMZ. Figure 4.13 Networking > Forwarding > DMZ The following table describes the items in the previous figure.
Item Description Destination IP Protocol Enter the IP address of the destination address. Click the drop-down menu to select the protocol type for the entry: TCP, UDP, ICMP. Enter the port number of the sender IP address. Enter the port number of the destination IP address. Click Delete to remove the entry from the Filter policy. Click Add to include the entry in the Filter policy. Click Apply to save the values and update the policy. Source port Destination port Delete Add Apply 4.
Item Description Channel Selection Click the drop-down menu to select Auto (default) or Manual. The Auto selection allows the device to select (2.4G or 5G) automatically. The Manual selection provides access to a selection of the option band (2.4G or 5G). Click the drop-down menu to select the band and channel bandwidth. Click Apply to save the values and update the screen. Channel bandwidth Apply 4.5.2 Advanced To access this page, click Wireless Settings > Advanced. Figure 4.
Item Description MAC Clone Click the drop-down menu to enable or disable (default) the client to clone and use the MAC address of the connected device. In MAC sensitive networks, the function allows to client to overcome the limitation of the IP-bridged behavior. Advanced Wireless Setting Transmission Power Click the drop-down menu to set the transmission power of the WiFi. By default the AP transmits at full power: Full, Half or Quarter.
4.5.4 Statistics To access this page, click Wireless Settings > Statistics. Figure 4.18 Wireless Settings > Statistics The following table describes the items in the previous figure. Item Description Overview Mode SSID Channel / Frequency Receive Statistics BSSID Signal Level Wlan status TX packets TX bytes RX packets RX bytes Display the current operation mode of the device. Display the SSID. Display the current channel / frequency of the device.
The following table describes the items in the previous figure. Item Description Refresh Click Refresh to update the screen. 4.5.6 Log To access this page, click Wireless Settings > Log. Figure 4.20 Wireless Settings > Log The following table describes the items in the previous figure. Item Description Download Click Download to download the log file. 4.6 Alarm You can set the e-mail server and SNMP Trap server in the Setting page, and set the event type in the Event page. 4.6.
To access this page, click Alarm > Setting. Figure 4.21 Alarm > Setting The following table describes the items in the previous figure. Item Mail Server Mail Server From Email address Email address 1 Email address 2 Email address 3 Email address 4 SNMP Trap Server Trap Server Trap Server Port Trap Version Trap Community SNMP Agent Setting Description Enter the SMTP mail server. Enter the email address. Enter the email address 1 to receive alarm emails. Enter the email address 2 to receive alarm emails.
Item Description Read Community Write Community Contact Location Apply Enter the read-only, public, community string. Enter the write-only, private, community string. Enter the individual designated the contact point for this event. Enter the designated location/department of the setting. Click Apply to save the values and update the screen. 4.6.2 Event The Alarm Event page allows the selection of triggers for system, DCD and DSR events for the alarm function. To access this page, click Alarm > Event.
4.6.3 LogFile To access this page, click Alarm > LogFile. Figure 4.23 Alarm > LogFile The following table describes the items in the previous figure. Item Description Log File Click the drop-down menu to select a specific action for the system log file. Available options: Download Log File, Remove Log File, Download and Remove Log File. Click Export to download the log file. Export 4.7 Administration 4.7.1 System To access this page, click Administration > System. Figure 4.
To access this page, click Administration > Syslogd. Figure 4.25 Administration > Syslogd The following table describes the items in the previous figure. Item Description Syslogd Apply Click Enabled or Disabled to set the logging service status. Click Apply to save the values and update the screen. 4.7.3 NTP / Time Function To access this page, click Administration > NTP / Time. Figure 4.26 Administration > NTP / Time The following table describes the items in the previous figure.
4.7.4 HTTP To access this page, click Administration > HTTP. Figure 4.27 Administration > HTTP The following table describes the items in the previous figure. Item Description HTTP common settings Redirect HTTP requests Click the drop-down menu to enable or disable the function. By to HTTPS default the function is disabled. When enabled, a NAT setting and Open Ports can be setup to direct connection requests to an internal server. HTTPS port Enter the port to forward HTTPS traffic, default: 443.
4.7.5 Scheduler To access this page, click Administration > Scheduler. Figure 4.28 Administration > Scheduler The following table describes the items in the previous figure. Item Description Reboot Time Click to Enabled or Disabled the Reboot scheduled function. Click to enable or disable the daily reboot schedule. Alternatively, disable Everyday to manually select a specific day and hour/minutes of the week to schedule the reboot. Click Apply to save the values and update the screen. Apply 4.7.
Item Description Load Factory Defaults Load Default Click Load Default to have all configuration parameters reset to their factory default values. All changes that have been made will be lost, even if you have issued a save. 4.7.7 Firmware Upgrade To access this page, click Administration > Firmware Upgrade. Figure 4.30 Administration > Firmware Upgrade The following table describes the items in the previous figure. Item Description Browse Upload Click Browse to select the configuration file.
Item Description IP Address / Name Enter the IP address or host name of the station to ping. The initial value is blank. The IP Address or host name you enter is not retained across a power cycle. Host names are composed of series of labels concatenated with periods. Each label must be between 1 and 63 characters long, maximum of 64 characters. Click Ping to display ping result for the IP address.
Chapter 5 Telnet Configuration 5
5.1 Overview The purpose of the Console Configuration is to help you manage your device in console mode. One of the main functions of the console mode is to change the web configuration login password. You can use terminal software like Hyper Terminal, Telix and other related terminal software. 5.2 Telnet Console 5.2.1 Create a new connection You can create a new Telnet connection and assign a connection name for the console configuration. Figure 5.
5.2.2 Input the IP address Confirm that the Telnet console configuration works ok. Be sure that your host PC Ethernet network IP domain is as same as the EKI-6233BN device, and the Telnet TCP port number is “23”. Figure 5.2 Creating a Telnet Connection 5.2.3 Connection Success After connecting to the device in HyperTerminal console, a welcome greeting displays. Figure 5.
5.
– parity n: None Parity. – parity e: Even Parity. – parity o: Odd Parity. – parity m: Mark Parity. – parity s: Space Parity. Usage: port [nn|all] mode [vcom|ctrl|data] Set the serial ports as virtual COM mode, control mode, or data mode. 5.3.4 mvcom Usage: mvcom Show all serial ports mode and related information. Usage: mvcom [nn|all] Set the “nn”th or all serial ports as the Virtual COM mode. Usage: mvcom [nn|all] idleto [] Set the “nn”th or all serial ports host idle timeout(S).
Value 0 : None Setting. Usage: mvcom [nn|all] bychar [NULL|] Set datapackage as character(HEX). Value 0 : None Setting. 5.3.5 mctrl Usage: mctrl Show all serial ports mode and related information. Usage: mctrl [nn|all] Set the “nn”th or all serial ports as the control mode. Usage: mctrl [nn|all] idleto [] guardt [] hangchr [] Set the “nn”th or all serial ports data idle timeout, guard time and hang character. 5.3.6 mdata Usage: mdata Show all serial ports mode and related information.
Usage: net [1|2] dns2 [d.d.d.d] Set network DNS2. Usage: net [1|2] to [d] Set network timeout. 5.3.8 alarm Usage: alarm Show current alarm informations. Usage: alarm mail server [null|address] from [null|address] to1 [null|address] to2 [null|address] to3 [null|address] to4 [null|address] Set current mail server configuration. Usage: alarm trap server [null|address] ver [1|2] community [null|name] Set current trap server configuration.
5.3.12 apply Usage: apply Save the settings to the flash memory and reboot the system immediately. 5.3.13 exit Usage: exit Terminate the shell session. 5.3.14 help Usage: help Display help information of command list. Usage: help [cmd] Show the usage of command. 5.3.15 wireless Usage: wireless Show or configure the wireless settings or informations. Usage: wireless ssid [] Set SSID. Usage: wireless country [us|de|fr|es|jp|kr|cn] channel [0|1|…|14] Set country code and channel.
Usage: wireless encryption [none|wep|wpa-psk|wpa-enterprise] Set encryption type. Usage: wireless wepidx [0|1|2|3] Set WEP key index. Usage: wireless wepkey [asc|hex] [] Set WEP key as [] in specific format. Usage: wireless wpakey [] Set WPA-PSK key as []. Usage: wireless wpaeap [tls|ttls|peap] Set WPA-Enterprise EAP method. Usage: wireless wpaid [] Set WPA-Enterprise identity as []. Usage: wireless wpapw [] Set WPA-Enterprise as [].
Usage: mrfc2217 [nn|all] Set port [nn|all] as RFC2217 mode. Usage: mrfc2217 [nn|all] idleto [] lsport [] Set host idle timeout(s) and listen port.
www.advantech.com Please verify specifications before quoting. This guide is intended for reference purposes only. All product specifications are subject to change without notice. No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd.
