DELOS200 USER MANUAL Version 1.1 2607 Colorado Blvd. Los Angeles, CA 90041 USA Tel: 323-254-8131 Fax: 323-254-4928 www.adrftech.
Delos200 RF Repeater User Manual V1.1 Version 1.1 (Released March 25, 2008) Information in this document is subject to change without notice. Advanced RF Technologies, Inc. 1996-2008. All rights reserved. Please send comments to: E-Mail: info@adrftech.com Phone: (323) 254-8131 (800) 313-9345 Fax: (323) 254-4928 Address: Advanced RF Technologies, Inc. Attention: Technical Publications Department 2607 Colorado Blvd., 1st Floor Los Angeles, CA 90041 USA www.adrftech.
Delos200 RF Repeater User Manual V1.1 TABLE OF CONTENTS 1. Introduction of Delos200....................................................................................5 1.1 Overview ......................................................................................................5 1.1.1 1.1.2 1.1.3 Highlights ......................................................................................5 Special Features..............................................................................
Delos200 RF Repeater User Manual V1.1 Appendix B: Button Operation......................................................................................27 Advanced RF Technologies, Inc.
Delos200 RF Repeater User Manual V1.1 1. Introduction of Delos200 1.1 Overview Delos200 series repeaters enhance in-building wireless coverage in the most effective and cost efficient way. For its intelligent design and versatility, Delos200 series repeaters are the ideal choice for wireless coverage problems indoors. Delos200 series repeaters can be used as a stand-alone repeater with passive antennas connected to it or it can also be used as a feeder repeater to a DAS (Distributed Antenna System). 1.
Delos200 RF Repeater User Manual V1.1 1. Server Antenna Port One end of the coax cable will connect to the “Server Antenna Port” of Delos200 while the other end of the cable will connect to the server antenna which is pointing towards the intended coverage area. 2. VFD Display In this display, you are able to view the repeater vitals in each link (e.g. RSS, Gain, Output Power & Alarms). ** Please refer to Appendix B for more detailed information on how the VFD button operates. 3.
Delos200 RF Repeater User Manual V1.1 6. Donor Antenna Port One end of the coax cable will connect to the “Donor Antenna Port” of Delos200 while the other end of the cable will connect to the donor antenna which is pointing towards the BTS. The coax cable coming in from the donor antenna (pointing towards the BTS) 7. USB Interface For management and troubleshooting purposes, you can connect your PC to Delos200 Manager via USB cable. 8.
Delos200 RF Repeater User Manual V1.1 1.2 Warnings and Hazards WARNING! ELECTRIC SHOCK Opening the Delos200 could result in electric shock and may cause severe injury. WARNING! EXPOSURE TO RF Working with the repeater while in operation, may expose the technician to RF electromagnetic fields that exceed FCC rules for human exposure. Visit the FCC website at www.fcc.gov/oet/rfsafety to learn more about the effects of exposure to RF electromagnetic fields.
Delos200 RF Repeater User Manual V1.1 WARRANTY Opening or tampering the Delos200 will void all warranties. FCC Part 15 Class A NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Delos200 RF Repeater User Manual V1.1 Delos200 Parts List The Delos200 repeater system includes: PART ID QUANTITY a. Delos200 Repeater Delos20X 1 c. **CD Delos200 Manager 1 b. Screws SC01 d. USB Cable USB01 e. Power Cable PWRC01 4 1 1 ** CD includes: (1) GUI Software; (2) User Manual; (3) Delos200 Quick Start Guide; & (4) Software & USB Driver Setup Guide. 1.3 Delos200 Software Installation and Requirements 1.4.
Delos200 RF Repeater User Manual V1.1 1.4 Pre-Installation using Delos200 Software Prior to the Delos200 installation, ensure that: a. The USB cable has been connected and proper communication has been established. b. The donor and server antennas are in place. c. The TX and RX communication status LEDs are lit green and blinking periodically on the Status Menu. ** The TX and RX LEDs should blink every 1 second only in the Status Menu.
Delos200 RF Repeater User Manual V1.1 2. Connect the Donor Antenna Connect one end of the RF coaxial cable to the donor antenna and the other end to the repeater Donor Antenna Port located on the top of the Delos200 as shown in Figure 2. 3. Connect the Server Antenna Connect one end of the RF coaxial cable to the server antenna and connect the other end to the repeater Server Antenna Port located on the top of the Delos200 as shown in Figure 2. 4.
Delos200 RF Repeater User Manual V1.1 7. Go to the Control Menu Now with the blinking TX and RX status LEDs on the Status Window, go to the Control Window. You will see the following: Figure 3 - Control Window of the Delos200 Software 8. Select the Desired Band(s) In the Band Selection section of the Control Window (Figure 3), click on the pull down arrows labeled “BW” and “Band.” You can choose your desired bandwidth (5, 10 or 15 MHz) by clicking on the pull down arrow labeled “BW.
Delos200 RF Repeater User Manual V1.1 ** Depending on which model of Delos200 is being used, the band options will vary. Delos201 doesn’t support the C band while the Delos202 model doesn’t support the A band. 9. Check the Front LED Panel Check that the Power LED is on (Green) and the Alarm LED (Red) is off. ** If the Alarm LED is on, refer to Section 2.3 on page 25.
Delos200 RF Repeater User Manual V1.1 2 User Manual V1.0 using Delos200 Software 2.1 Menu Structure 2.1.1 Window Overview Status Control you to monitor the current you to select the operating The Status Window allows settings and status of the Delos200. The Control Window enables band and change or adjust the Delos200’s parameters and settings. Figure 4 - Status Window of the Delos200 Software Advanced RF Technologies, Inc.
Delos200 RF Repeater User Manual V1.1 2.1.2 Status Menu The Status Window is the monitoring window of the Delos200 Software. This window enables the user to monitor the status and settings of the Delos200. In other words, no parameters can be changed in the Status Window. Window. To change parameters, you will need to go to the Control Bands Bandwidth Indicates the bandwidth of the selected filter. Currently selected band(s) are highlighted.
Delos200 RF Repeater User Manual V1.1 2.1.3 Control Menu The Control Window lets the user to change parameters of the repeater. Figure 6 - Control Window of the Delos200 Software Band Selection Depending on which model of the Delos200 you have, you can choose the desired filter from the drop down menu by clicking on BW and the corresponding band options can be viewed by clicking on Band. Please refer to Table 2 on page 12 for all the possible band combinations.
Delos200 RF Repeater User Manual V1.1 Downlink/Uplink HPA Mode The HPA mode enables the user to turn the HPA on or off. If the HPA is turned off on either link, the Delos200 will not operate properly. Both HPAs needs to be turned on for the RF portion of the repeater to work in both directions (downlink and uplink). By default, the Downlink/Uplink HPA ON box are checked. Either or both HPAs can be turned off for troubleshooting purposes during an installation process.
Delos200 RF Repeater User Manual V1.1 2.1.4 System Menu 2.1.4.1 Info. Window The Info. Window displays the Model Number, Serial Number and Firmware Version of the Delos200 repeater. Contact information is included along with a link to Advanced RF Technologies, Inc.’s URL. Figure 7 - Info. Window of the Delos200 Software Advanced RF Technologies, Inc.
Delos200 RF Repeater User Manual V1.1 2.1.4.2 Upgrade Window In order to download the latest repeater firmware, click on the Upgrade Window. The firmware file will be provided by the technical support group from Advanced RF Technologies, Inc. Once the firmware file has been saved on the PC, you would connect the Delos200 repeater to the PC via the USB cable provided. Click on “Open” and locate the firmware file and click on ‘Download.
Delos200 RF Repeater User Manual V1.1 3 Maintenance Guide for Delos200 3.1 Periodic Inspection Checklist a. Check for loose connections to the repeater and antennas. If connections are loose, make sure that all connections are tightly fastened properly. b. Cables and connectors are in good condition. c. Ensure that the repeater brackets are in good condition and that the repeater is securely fastened. 3.2 Preventive Measures for Optimal Operation 3.2.1 • 3.2.
Delos200 RF Repeater User Manual V1.1 4 Troubleshooting 4.1 Tx & Rx LEDs Tx Rx Blinking Blinking GREEN GREEN Blinking Solid GREEN GREEN Explanation Successful Connection. The Delos200 Software and the repeater are communicating successfully. The repeater is not receiving any commands from the software. In this state, the repeater is either processing or executing a command. Wait for a few seconds for the Rx LED to blink periodically.
Delos200 RF Repeater User Manual V1.1 4.2 Common Installation Problems Problem USB port is not being recognized The power green LED on the front panel is not lit. GUI Software & Laptop - No Communication Status Window – Weak Signal or Donor RSS Downlink/Uplink Over Power Alarm Possible Solution You would need to install the driver for the USB cable which can be found with the CD that comes with the repeater. Check if the power switch is turned on.
Delos200 RF Repeater User Manual V1.1 5.3 Limitation of Damages The liability for any defective product shall in no event exceed the purchase price for the defective product. 5.4 No Consequential Damages Advanced RF Technologies, Inc. has no liability for general, consequential, incidental or special damages. 5.5 Additional Limitation on Warranty Advanced RF Technologies, Inc. standard warranty does not cover products which have been received improperly packaged, altered, or physically damaged.
Delos200 RF Repeater User Manual V1.1 Appendix A: Specifications ELECTRICAL SPECIFICATIONS PARAMETERS Frequency Range SPECIFICATIONS DL 1930 to 1990 MHz UL 1850 to 1910 MHz COMMENTS Model 1 Sub Band Filtering 5/10/15 MHz Sliding Filter DL: 1930-1975 MHZ / UL: 1850-1895 MHZ Model 2 Sub Band Filtering 5/10/15 MHz Sliding Filter DL: 1945-1990 MHZ / UL: 1865-1910 MHZ Operating Frequency Programmable Frequency Error ≤ +/- 0.
Delos200 RF Repeater User Manual V1.1 MECHANICAL SPECIFICATIONS PARAMETERS SPECIFICATIONS Housing (W x H x D) 8.27 x 11.03 x 3.57 inches Housing Material Aluminum & Plastic Weight ≤ 11 lbs Connector Type Antenna N-Type (Female) Software Interface USB Cooling COMMENTS External Convection POWER SPECIFICATIONS PARAMETERS SPECIFICATIONS COMMENTS Main AC Power 100 to 240 VAC Power Adapter complies AC Frequency 50 to 60 Hz Adaptor Voltage & Current 6 VDC / 4.
Delos200 RF Repeater User Manual V1.1 Appendix B: Button Operation Normal Operation Advanced RF Technologies, Inc.
Delos200 RF Repeater User Manual V1.1 Soft Fail Alarm Operation Advanced RF Technologies, Inc.
Delos200 RF Repeater User Manual V1.1 Hard Fail Alarm Operation Advanced RF Technologies, Inc.
Delos200 RF Repeater User Manual V1.1 Filter and Operating Band Advanced RF Technologies, Inc.