Verizon Wireless ADRF-25K USER MANUAL Version 0.3 2607 Colorado Blvd. Los Angeles, CA 90041 USA Tel: 323-254-8131 Fax: 323-254-4928 www.adrftech.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 Glossary The following is a list of abbreviations and terms used throughout this document.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 First released version : Information in this document is subject to change without notice. Advanced RF Technologies, Inc. 1996-2007. All rights reserved. Please send comments to: E-Mail: info@adrftech.com Phone: Fax: (323) 254-8131 (800) 313-9345 (323) 254-4928 Address: Advanced RF Technologies, Inc. Attention: Technical Publications Department 2607 Colorado Blvd., 1st Floor Los Angeles, CA 90041 USA www.adrftech.com Revision History Version Author 0.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 TABLE OF CONTENTS 1. 2. 3. 4. 5. ADRF-25K...................................................................................................................... 6 1.1 Introduction................................................................................................................ 6 1.1.1 Highlights ......................................................................................................... 6 1.1.2 Parts List...................
Verizon Wireless MPE25K RF Repeater User Manual V0.3 5.3 Limitation of Damages ............................................................................................ 36 5.4 No Consequential Damages..................................................................................... 36 5.5 Additional Limitation on Warranty ......................................................................... 36 5.6 Return Material Authorization (RMA) ................................................................
Verizon Wireless MPE25K RF Repeater User Manual V0.3 1. ADRF-25K 1.1 Introduction Dual bands in one body: ADRF-25K is an over-the-air repeater system that operates in both the Cellular (824 - 894 MHz) and PCS (1850 – 1990 MHz) frequencies. It has one input and one output port. 1.1.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 1.1.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 1.1.3 Repeater Quick View Display LED (Page12) Upper Guard Screw (Page16) Bracket Screw (Page16) Modem Lower Guard Screw (Page16) Ground Hole (Page17) Figure 2 ADRF-25K Front & Side Views Donor Antenna Port Server1 Antenna Port (Page14) (Page14) Server2 Antenna Port (Page14) Power switch (page14) Anchor Bolt Hole (page16) Ethernet Port (page14) Figure 3 – ADRF-25K Back & Bottom Views Advanced RF Technologies, Inc.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 1.2 Warnings and Hazards WARNING! ELECTRIC SHOCK Opening the ADRF-25K could result in electric shock and may cause severe injury. WARNING! EXPOSURE TO RF Working with the repeater while in operation, may expose the technician to RF electromagnetic fields that exceed FCC rules for human exposure. Visit the FCC website at www.fcc.gov/oet/rfsafety to learn more about the effects of exposure to RF electromagnetic fields.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 Lithium Battery : CAUTION. RISK OF EXPLOSION IF BATTERY IS REPLACED BY INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO INSTRUCTIONS. Ethernet Instructions: This equipment is for indoor use only. All cabling should be limited to inside the building. FCC Part 15 Class A NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 Industry Canada This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 2. ADRF-25K Overview 2.1 Operation Modes 2.1.1 Local Web GUI Turn on the power switch of the ADRF-25K. Wait until the Power LED on the front panel is lit in green. Simply connect one end of the Ethernet cable on one of the three repeater monitor Ethernet ports and the other end on the PC’s LAN port. Launch the Microsoft Internet Browser (Internet Explorer) and type in the IP address (http://192.168.63.1). The Local Web GUI will be launched.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 2.2 Switches & Indicators 2.2.1 LEDs ADRF-25K has LEDs on the front panel of the repeater as shown below in Figure 4.
Verizon Wireless MPE25K RF Repeater User Manual V0.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 2.2.2 Power Switch The AC Power on/off switch is located at the bottom of repeater. The switch should be powered on after the repeater has been installed properly. Figure 5 – ADRF-25K Repeater Power Switch View 2.2.3 Ethernet Port Figure 6 – Ethernet Port 2.2.4 RF Port - Donor: Connect the COM port of the diplexer - Server 1 Connect the Server antenna - Server 2 For use with an auxiliary server antenna.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 2.3 Installation 2.3.1 Tools No special tools or equipment are needed to install the ADRF-25K. 2.3.2 Procedure Four mounting holes are located on the wall-mounting bracket to attach it to the wall. The wall bracket must be securely attached to sufficiently carry the weight of the ADRF-25K, which is bolted to the wall bracket through the four aligned mounting holes.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 Figure 7 – Repeater Mounting Instructions Advanced RF Technologies, Inc.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 2.3.3 Grounding A ground cable is included in the box. The ground cable should be connected to the ADRF-25K before the repeater is turned on. Figure 8 – Ground Cable Connection Advanced RF Technologies, Inc.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 2.3.4 Antenna Separation/Isolation Separation between the antennas is necessary to prevent oscillation. Oscillation occurs when the signal entering the system continually reenters, due to the lack of separation between the donor and server antennas. In other words, the signal is being fed back into the system. This creates a constant amplification of the same signal. As a result, the noise level rises above the signal level.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 2.3.5 Line of Sight The donor antenna which points towards the base station typically has a narrow beam antenna pattern. As a result, a slight deviation away from the direction of the BTS can lead to less than optimum results. In addition, obstacles between the repeater and the BTS may impair the repeater from obtaining any BTS signal. As a result, the repeater cannot transmit signal to the coverage area.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 3. ADRF-25K AROMS Setup 3.1 Repeater/PC Connection Using AROMS i) Wait until the Power LED is lit in green. Connect the LAN cable between the laptop’s Ethernet port and the repeater’s Ethernet port. Note: Under Local Area Connection in Network Settings, make sure to select Obtain an IP address automatically under Internet Protocol (TCP/IP) properties. ii) Launch MS Internet Explorer (Version 6.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 iv) The following login screen will appear: If you are not the Super-User, please type in your assigned username & password which you should have received from the Super-User. The default username and password for the General User is adrf & adrf, respectively. If the username & password is typed in incorrectly, the following screen will appear: Advanced RF Technologies, Inc.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 3.2 Repeater Status 3.2.1 Cellular Repeater Status If you click on Status tab, the following window will appear: In this window, the user can view the following: (To change any parameters, e.g., Cellular Band, Gain Settings, you will need to go to the Install or Control Menu.) - Cellular Band: Will display the center frequencies of the 800 MHz spectrums on the downlink and uplink respectively.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 - Alarm: Will display eleven alarms with three different status conditions (Normal, Soft Fail or Hard Fail). - Message Board: Will show up to recent 20 log messages (Alarms & Heartbeats). - Modem: Will display the status of the mode (e.g. Disabled, Not Connected or Connected) - Installation: Will display repeater’s installation status (Not Installed or Installed). - Repeater Info: Will display repeater’s serial number, modem ESN and MDN.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 3.2.2 PCS Repeater Status If you click on Status tab, the following window will appear: In this window, the user can view the following: (To change any parameters, e.g., PCS Band, Gain Settings, you will need to go to the Install or Control Menu.) - PCS Band: Will display the center frequencies of the 1900 MHz spectrums on the downlink and uplink respectively.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 - Alarm: Will display eleven alarms with three different status conditions (Normal, Soft Fail or Hard Fail). - Message Board: Will show up to recent 20 log messages (Alarms & Heartbeats). - Modem: Will display the status of the mode (e.g. Disabled, Not Connected or Connected) - Installation: Will display repeater’s installation status (Not Installed or Installed). - Repeater Info: Will display repeater’s serial number, modem ESN and MDN.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 3.3 Repeater Control If you click on Control window at PCS, the following window will appear If you click on Control window at Cellular, the following window will appear Advanced RF Technologies, Inc.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 In this window, the user can adjust the following parameters: General Setting - Automatic Gain Control (Default mode is On) - Downlink HPA on/off (Default mode is On) - Uplink HPA on/off (Default mode is On) - Uplink Tracking mode on/off (Default mode is Off) Manual Gain Control - Downlink Gain Control Cellular: 42 to 72 dB @ 0.5 dB step, default value: 72 dB PCS: 51 to 81 dB @ 0.
Verizon Wireless MPE25K RF Repeater User Manual V0.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 3.4 Repeater Installation If you click on the Install tab, the following window will appear: - Cellular Installation Window - PCS Installation Window Advanced RF Technologies, Inc.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 - Band Selection: Simply click on the desired operating bandwidth. Cellular: Simply select the desired Band. The Main Band (A+A” or B) must be selected and cannot be switched ON/OFF. PCS: Simply select the desired Band Width and corresponding Band(s). - Cellular Band Selection - PCS Band Selection - Modem: By default, auto-connection box is checked so that the modem will connect automatically once sufficient donor signal is present.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 3.5 System 3.5.1 Account If you click on System tab, the following window will appear: Note: If you are the Super User, you will see account management section under the System Window. If you are a local user, you will not be able to see the account management portion. Super-User Only the Super-User can add, delete and modify a user.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 Administrator The following window illustrates how a new administrator can be added by simply clicking on Administrator. 3.5.2 Firmware Upgrade If you click on Firmware Upgrade, the following window will appear. You can browse through your PC and locate the firmware file. Once it is selected, simply click on Update and the latest firmware will be automatically uploaded and the session will close. You will need to re-login.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 3.5.3 System Info Displays the system info in a simple text format. Displays the Input/Output/Gain, Alarm status, and Modem status of both the Cellular and PCS bands. Advanced RF Technologies, Inc.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 4. Maintenance Guide for ADRF-25K 4.1 Periodic Inspection Checklist a. Check for loose connections between the repeater and antennas. If connections are loose, make sure that all connections are tightly fastened properly. b. Cables and connectors are in good condition. c. Ensure that the repeater brackets are in good condition and that the repeater is securely fastened. 4.2 Preventive Measures for Optimal Operation 4.2.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 5. Warranty and Repair Policy 5.1 General Warranty The ADRF-25K carries a Standard Warranty period of three years unless indicated otherwise on the package or in the acknowledgment of the purchase order. All antennas (PCS Yagi, Cellular Yagi, Dual Band Omni), cables and diplexer all carry a Standard Warranty period of ten years under normal operating conditions. 5.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 To request an RMA, please call (323) 254-8131 or send an email to techsupport@adrftech.com. Advanced RF Technologies, Inc.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 Appendix A: Specifications A.1 Electrical Specifications Specifications Parameters Cellular A band [(A+A”)=A+A’ ] Frequency Cellular B band (B+B’) PCS Sub Band Filtering Roll off Downlink Uplink 869.0~880.0 MHz 824.0~835.0 MHz, 890.0~891.5 MHz 880.0~890.0 MHz 845.0~846.5 MHz 846.5~849.0 MHz 1930.0~1990.0 1850.0~1910.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 Gain Control Range AGC Setting Range Cellular ≥ 30 dB PCS ≥ 30 dB Cellular - 5 ~ + 15 dBm - 10 ~ + 10 dBm PCS - 2 ~ + 18 dBm - 8 ~ + 12 dBm EVDO Gain Offset Cellular Noise Figure PCS ≤ 8.5dB @ Max Gain ≤ 7.0dB @ Max Gain ≤ 7.5dB @ Max Gain ≤ 7.0dB @ Max Gain ≤ 8.5dB @ Min Gain ≤ 8.0dB @ Min Gain ≤ 9.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 A.3 Power Supply Specifications Input Voltage Line Frequency Current Protection Power Factor Correction Configuration 100 to 250VAC, ±10% 47 to 63Hz 2.0A max at 90VAC Input Internal Primary Current Fuse Inrush Limiting Complies with EN61000-3-2 and EN61000-3-3 Inlet Type: IEC320-C14, C18 Output Combined Line and Load Voltage Regulation Ripple Transient Response Hold-up Time Protection ±1% (excluding cord) 1% Vp-p max. 0.5ms for 50% load change Typ.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 A.4 Antenna Specifications A.4.1 Server Antenna z Electrical Specifications Parameters Frequency Range Gain VSWR Hori, Beam Width Polarity IMD Connector Maximum Power Rating Impedance Specifications 824 ~ 894 MHz , 2 dBi (Min) ≤ 2:1 Omni Vertical ≥ 165 dBc N type, Female 20 Watt 50 Ohms Remarks 1920 ~ 2170 MHz 4 dBi (Min) z Mechanical Specifications Parameters Specifications Diameter 7.244 inches ( 184 mm ) Dimension Height 4.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 z Beam Patterns - CDMA Horizontal Beam Pattern - CDMA Vertical Beam Pattern Advanced RF Technologies, Inc.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 - PCS Horizontal Beam Pattern - PCS Vertical Beam Pattern Advanced RF Technologies, Inc.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 A.4.2 PCS Donor Yagi Antenna z Electrical Specifications Parameters Frequency Range Gain VSWR Specifications 1750 ~ 2170 MHz ≥ 12 dBi (Min) ≤ 1.3:1 Remarks H ≥ 28° 29~46 V 34~37 F-B Ratio IMD Maximum Power Rating ≥ 34° ≥ 15 dB ≥ 165 dBc 50 Watt Impedance 50 Ohms Beam Width z Mechanical Specifications Parameters Specifications 4.212 × 3.228 × 19.685 inches Dimension ( 107 × 82 × 500 mm ) Weight 3.307 lbs ( 1.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 z Test Results - PCS Horizontal Beam Pattern - PCS Vertical Beam Pattern Advanced RF Technologies, Inc.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 - PCS IMD Test Advanced RF Technologies, Inc.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 A.4.3 Cellular Donor Yagi Antenna z Electrical Specifications Parameters Frequency Range Gain VSWR Specifications 824 ~ 894 MHz ≥ 12 dBi (Min) ≤ 1.3:1 Remarks H ≥ 35° 33~42 V 33~40 F-B Ratio Maximum Power Rating ≥ 32° ≥ 15 dB 50 Watt Impedance 50 Ohms Beam Width z Mechanical Specifications Parameters Dimension( length ) Weight Connector Specifications 49.217 inches (1250 mm ) 2.511 lbs ( 2.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 z Beam Patterns - Cellular Horizontal Beam Pattern - Cellular Vertical Beam Pattern Advanced RF Technologies, Inc.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 z Tilt Bracket for Cellular Yagi Antenna Advanced RF Technologies, Inc.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 A.5 Diplexer Module Specifications z Electrical Specifications Type Cellular (Low Port) PCS (High Port) Frequency 800 ~ 940MHz 1.84 ~ 2GHz Ripple ≤ -0.5dB Loss ≤ -1.0 dB VSWR ≤ 1.4 : 1 Impedance 50 Ohms Isolation ≥ -55 dB Maximum Power 50 Watt Rating Dimension 1.96*3.93*2.55 inches ( 50*100*65 mm) Advanced RF Technologies, Inc.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 - Full Band - Cellular Advanced RF Technologies, Inc.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 - PCS - Port Isolation Advanced RF Technologies, Inc.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 A.6 Cable Specifications z Coaxial Cable Specifications Length Loss Cellular PCS 3 ft (1M) ≤ 0.2 dB ≤ 0.3 dB 150 ft (45.71M) ≤ 4 dB ≤ 5.5 dB 30 ft (9.14M) ≤ 1.2 dB ≤ 1 dB Weight ≤0.485 lb (220g) / EA ≤22.31 lb (10.12 Kg) / EA ≤4.60 lb (2.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 z Test Results for 30 ft (9.14M) Cable - PCS - Cellular Advanced RF Technologies, Inc.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 z Test Results for 150 ft (45.71M) Cable - PCS - Cellular Advanced RF Technologies, Inc.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 Appendix B: Mechanical Drawing Advanced RF Technologies, Inc.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 Appendix C: ADRF-25K Overview C.1 Block Diagram Advanced RF Technologies, Inc.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 C.1 Components Server2 Port Server1 Port Donor Port Triplexer Cellular UP/Down PCS Duplexer PCS UP/Down Converter Power Supply Controller Modem Module AC Port DHCP Sub Board Advanced RF Technologies, Inc.
Verizon Wireless MPE25K RF Repeater User Manual V0.3 Power Supply It provides DC power to each module within the repeater. Controller It is responsible for monitoring the status of each module and controls the parameters. PCS Up / Down Converter Module The downlink RF signal that enters through the cavity filter is converted to IF frequency, which is later converted back to RF frequency through SAW filtering.