FLEXMINI User’s Manual
Service Information Your New Radio System Thank you for your purchase of ARC FLEX MINI radio remote control system. Without a doubt, our FLEX MINI system is the ultimate solution for providing precise, undeterred, and safe control of your material.
Table of Contents Page 1. General System Information 1.1 1.2 2. Transmitter 1.1.1 External Illustration 3 1.1.2 Internal Illustration 4 Receiver 1.2.1 External Illustration 5 1.2.2 Internal Illustration 6 Function Settings 2.1 Transmitter 2.2 3. 4. 5. 6. 7. 2.1.1 Channel Setting 7 2.1.2 Keypad Type Setting 8 2.1.3 Remote Pairing 9 Receiver 2.2.1 Dipswitch Setting 10 2.2.
Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
1. GENERAL SYSTEM INFORMATION 1.1 TRANSMITTER 1.1.1 External Illustration 9 1. 2. 3. 4. 5. 2 1 4 3 6 5 8 7 Pushbutton 1 Pushbutton 2 Pushbutton 3 Pushbutton 4 Pushbutton 5 6. 7. 8. 9.
1.1.2 Internal Illustration 9 10 2 1 4 3 11 6 5 8 7 12 13 1. 2. 3. 4. 5. 6. 7. Pushbutton 1 Pushbutton 2 Pushbutton 3 Pushbutton 4 Pushbutton 5 Pushbutton 6 Pushbutton 7 8. 9. 10. 11. 12. 13.
1.2 RECEIVER 1.2.1 External Illustration 3 2 1 4 7 5 6 1. 2. 3. 4. COM LED Status LED Power LED Output Relays LED 5. 6. 7.
1.2.2 Internal Illustration 1 2 3 1. 2. 3.
2. FUNCTION SETTINGS 2.1 TRANSMITTER 2.1.1 Channel Setting 1 ON PB3 + Set transmitter channel by moving the function dipswitch located inside the battery compartment to “on” position. Reinsert the two batteries and press any button to power up the transmitter. At this point the Status LED will display a series of red, green and orange blinks showing the current software version. Then press and hold PB3 for up to 1 second to go into the transmitter channel setting mode.
2.1.2 Keypad Type Setting 1 ON PB4 + Set transmitter keypad type by moving the function dipswitch located inside the battery compartment to “on” position. Reinsert the two batteries and press any button to power up the transmitter. At this point the Status LED will display a series of red, green and orange blinks showing the current software version. Then press and hold PB4 for up to 1 second to go into the keypad type setting mode.
2.1.3 Remote Pairing 1 ON PB4 PB3 + Set remote pairing function by moving the function dipswitch located inside the battery compartment to “on” position. Reinsert the two batteries and press any button to power up the transmitter. Then press and hold PB3 and PB4 at the same time for up to 1 second to go into the remote pairing setting mode (Status LED off).
2.2 RECEIVER 2.2.
3. RECEVIER INSTALLATION * ( ) For keypad type #2 and type #3 setups.
Secure the mounting bracket to the wall or equipment via two screws (not provided with the system). Slide down the receiver along the guided track to secure the receiver to the mounting bracket (see below). Make sure the screws are tightened after installation. WALL → Remove the receiver by pressing down the bracket release and pull the receiver upward until it clears the guided track (see below).
4. OPERATING PROCEDURE General Operating Procedure The Flex Mini transmitter and receiver operate by means of RF transmission. When any of the eight (8) buttons on the transmitter is pressed it will activate the designated output relay in the receiver. When the button is released the designated output relay in the receiver is deactivated. When the button is released the transmission stops within 2 seconds.
5.
6. CHANNEL FREQUENCY TABLE Channel Frequency Channel Frequency 1 433.050MHZ 17 433.850MHZ 2 433.100MHZ 18 433.900MHZ 3 433.150MHZ 19 433.950MHZ 4 433.200MHZ 20 434.000MHZ 5 433.250MHZ 21 434.050MHZ 6 433.300MHZ 22 434.100MHZ 7 433.350MHZ 23 434.150MHZ 8 433.400MHZ 24 434.200MHZ 9 433.450MHZ 25 434.250MHZ 10 433.500MHZ 26 434.300MHZ 11 433.550MHZ 27 434.350MHZ 12 433.600MHZ 28 434.400MHZ 13 433.650MHZ 29 434.450MHZ 14 433.700MHZ 30 434.
7. SYSTEM SPECIFICATIONS Model no. : FLEX MINI Frequency Range : 433~434 MHz Frequency Deviation : 50 KHz Number of Channels : 32 channels Modulation : Digital Frequency Modulation based on Manchester Code, 24bit address, and 8bit CRC Parity Check.