Version 1.
Version 1.6 Last updated: 2021-09-01 LumiCon User Guide TABLE OF CONTENTS 1 2 System Overview and Components ...................................................................................................... 2 1.1 Parts List ........................................................................................................................................ 2 1.2 System Overview & System Components .....................................................................................
Version 1.6 Last updated: 2021-09-01 1 SYSTEM OVERVIEW AND COMPONENTS 1.1 PARTS LIST Description Quantity LumiHub 1 LumiHub Power Supply 1 LumiNode As required LumiSense cables As required Zip es‡ As required ‡ Zip ties: 1 per LumiNode + 1 every 2 ft per LumiSense Cable 2 155 Gordon Baker Road Suite 301, Toronto, Ontario M2H3N5 Support contact: support@aoms-tech.com | 1-877-873-1942 www.aoms-tech.
Version 1.6 Last updated: 2021-09-01 1.2 SYSTEM OVERVIEW & SYSTEM COMPONENTS Accessories GPS LoRa LTE 1x Slim Model Antenna x3 Backplate x1 Screw x4 Hose clamp x2 Wood screw x4 LumiHub Power Supply Options OR 1x As Required Standard Power Supply Box 100 ft Power Supply Reel Regular Temperature probe With data logger Multi-point sensor cable Ruggedized Zip ties Zip ties 3 155 Gordon Baker Road Suite 301, Toronto, Ontario M2H3N5 Support contact: support@aoms-tech.
Version 1.6 Last updated: 2021-09-01 2 SET UP AND MOUNT LUMIHUB (SLIM MODEL) 2.1 INSTALLATION LOCATION In typical construction sites our LumiHub covers a 500-meter radius. If a line of sight between the LumiHub and a LumiNode can be maintained, up to 2km is possible from our previous site tests.
Version 1.6 Last updated: 2021-09-01 2.2 ANTENNA & BACKPLATE INSTALLATION LoRa GPS LTE Antennas x3 Backplate x1 Philips Screw Driver Screw x4 Ensure antennas are connected in their respective ports. Tighten by hand until no thread is visible. 5 155 Gordon Baker Road Suite 301, Toronto, Ontario M2H3N5 Support contact: support@aoms-tech.com | 1-877-873-1942 www.aoms-tech.
Version 1.6 Last updated: 2021-09-01 2.3 MOUNTING AND POWER CONNECTION Wall Mounting instructions (next page) Pole Mounting instructions (below) 2.3.
Version 1.6 Last updated: 2021-09-01 Wall Mounting instructions (below) 2.3.
Version 1.6 Last updated: 2021-09-01 2.4 POWER SUPPLY SETUP AND CONNECTION Power Supply Box instructions (below) 2.4.1 Power Supply Reel instructions (next page) Power Supply Box Setup Turn connector until no thread is visible Turn connectors until a click can be heard. 8 155 Gordon Baker Road Suite 301, Toronto, Ontario M2H3N5 Support contact: support@aoms-tech.com | 1-877-873-1942 www.aoms-tech.
Version 1.6 Last updated: 2021-09-01 Power Supply Reel instructions (below) 2.4.2 Power Supply Reel Setup Unwind the AC cable from front panel Turn dial on the back to lock/unlock reel Ensure handle is pointed up Turn connectors until a click can be heard. Turn connector until no thread is visible WARNING! READ BELOW CAREFULLY BEFORE USE Use the reel in upright position at all times. Do not use the reel in any other orientation.
Version 1.6 Last updated: 2021-09-01 3 SET UP LUMICON MOBILE APPLICATION Download the LumiCon mobile application from either the Google Play Store or the Apple App Store. STEP 1 Enter the following credentials to access the LumiCon app: STEP 2 Authentication Code Username Password The main dashboard groups projects into “Concrete Sensors” and “Materials Tracking.” Tap on Concrete Sensors and then tap “New Project” to add a new project. STEP 3 Enter a project name.
Version 1.6 Last updated: 2021-09-01 STEP 4 Once your project is saved, it is visible on the main page. Tap on the project that was created to access the jobs page. STEP 5 Tap on “New Job” to create a new job. STEP 6 Enter a name for pour and job name. For Example: Pour: “Mix 231 – July 29” Job Name: “Calibration Cylinder A” Scan the QR code found on the LumiSense cable tag or manually enter the ID. Scan the QR code found on the LumiNode or manually enter the ID.
Version 1.6 Last updated: 2021-09-01 STEP 7 For concrete profile drop down box, select the profile “None”. Scroll back up to click “Add” to add this job STEP 8 When the new job is saved, it will be visible in the jobs view. STEP 9 Insert the LumiSense cable into the LumiNode by aligning the white dots located at the connectors and tightening the nut until no thread is visible ensure a watertight seal. The “Link” LED on the LumiNode will start flashing. Check the LumiCon app.
Version 1.6 Last updated: 2021-09-01 4 LUMISENSE AND LUMINODE INSTALLATION Zip ties (1 per LumiNode + 1 every 2 feet of LumiSense cable) Tighten connector until no thread is visible Ensure zip ties are placed and secured at every 2 feet of the rebar. Point face towards the LumiHub, for the best wireless performance 13 155 Gordon Baker Road Suite 301, Toronto, Ontario M2H3N5 Support contact: support@aoms-tech.com | 1-877-873-1942 www.aoms-tech.
Version 1.6 Last updated: 2021-09-01 5 JOB COMPLETION 5.1 STOP THE IN-APP JOB MONITORING When a pour reaches maturity and no longer requires monitoring, you will need to end the job on the LumiCon app to prevent further alarms from being triggered. STEP 1 Enter the following credentials to access the LumiCon app: Authentication Code Username Password STEP 2 Navigate to the project page. You can also use the search bar to quickly find the project.
Version 1.6 Last updated: 2021-09-01 5.2 UNMOUNT THE LUMINODE After the job is complete, the LumiSense Cable is consumed but the LumiNode can be used again for the next temperature monitoring job. 1. Unplug the LumiSense Cable from the LumiNode, and immediately twist on the LumiNode cap to protect the port. LED will stop flashing once unplugged. 2. Release the LumiNode by cutting or unlocking the zip-tie holding the LumiNode in place. 3.
Version 1.6 Last updated: 2021-09-01 6 TROUBLESHOOTING STEPS 16 155 Gordon Baker Road Suite 301, Toronto, Ontario M2H3N5 Support contact: support@aoms-tech.com | 1-877-873-1942 www.aoms-tech.
Version 1.6 Last updated: 2021-09-01 7 REGULATORY STATEMENTS 7.1 FEDERAL COMMUNICATIONS COMMISSION (FCC) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.
Version 1.6 Last updated: 2021-09-01 7.2 INNOVATION, SCIENCE AND ECONOMIC DEVELOPMENT CANADA (ISED) This device complies with ISED Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme avec ISED Canada applicables aux appareils radio exempts de licence.