User Manual

ManualsBrandsAdvanced Control Technologies ManualsElectronicsWall Mounted Dimmer

Z-Wave ZDW120 Instructions, Series 300, Release 3.10

P/D 060210

HomePro

by ADVANCED CONTROL TECHNOLOGIES, INC.

0795-01

Z-Wave Radio Frequency (RF) Controlled, 500W, 120 VAC,

Two Wire, Wall Mounted Dimmer, Series 300, Release 3.10

ZDW120 V3

ZDW120 WALL MOUNTED DIMMER

The ZDW120 Wall Mounted Dimmer is a component of the HomePro lighting control system. Wire the Wall

Mounted Dimmer in place of the standard wall switch according to the diagram above and program from the

Wireless Controller to operate loads. Inclusion of the ZDW120 Wall Mounted Dimmer on the ZTH100 Wireless

Controller menu allows remote ON/OFF control and dimming of lights connected.

This Wall Mounted Dimmer is designed to work with other Z-Wave enabled devices. Z-Wave nodes of other

types can be added to the system and will also act as repeaters if they support this function of repeating the

signal received to other modules in the system.

This product supports 40Kbps data transmission. This product can also be used for networking support in

systems that stream metadata. An example might include transmission of information from audio devices such

as song title, artist, and album information to various displays around the home.

As part of a Z-Wave network, the ZDW120 will also act as a wireless repeater to insure that commands intended

for another device in the network are received. This is useful when the device would otherwise be out of the

radio range of the wireless controller.

There are no eld repairable assemblies on this unit. If service is needed, the unit must be returned where

purchased.

Read and understand these instructions before installing. This device is intended for installation in accordance

with the National Electric code and local regulations in the United States, or the Canadian Electrical Code and

local regulations in Canada. It is recommended that a qualied electrician perform this installation.

CAUTION! To reduce the risk of overheating and possible damage to other equipment, do not install to

control a receptacle, a motor operated appliance, a uorescent lighting xture, or a transformer-supplied ap-

pliance, but only permanently installed incandescent lamp xtures. Make sure the lamp(s) to be controlled

directly from this dimmer total no more than 500 watts. Retain instructions for future use.

INSTALLATION

DANGER! - SHOCK HAZARD. Make all connections with the POWER OFF to avoid injury to the installer or

damage to the device.

1. Strip 3/4” of insulation from the ends of the conductors (if not already done) and make connec-

tions as shown in the Wiring Diagram. Note that the line side of the load must be switched.

HomePro

RF Home Automation

Supplied with matching deco-

rative switch plate

Note: This module must be “Included in the

Network” only where it will be permanently

installed. The proper operation of this node in

the mesh network is dependent on it knowing its

location with respect to other nodes. You cannot

“test bench” congure this module.

• This product supports Zensor Net Beam technology

Summary of content (5 pages)

PAGE 1
HomePro RF Home Automation ZDW120 V3 Z-Wave Radio Frequency (RF) Controlled, 500W, 120 VAC, Two Wire, Wall Mounted Dimmer, Series 300, Release 3.10 Supplied with matching decorative switch plate Note: This module must be “Included in the Network” only where it will be permanently installed. The proper operation of this node in the mesh network is dependent on it knowing its location with respect to other nodes. You cannot “test bench” configure this module.
PAGE 2
. Check connections to be sure they are tight and no bare conductors are exposed. 3. Make sure the load or installation does not exceed the device rating. 4. Restore the power. Wire this Wall Mounted Dimmer in place of an existing wall switch according to the diagram. See the ZTH100 Wireless Controller operating instructions to add this module under the command of the Wireless Controller.
PAGE 3
LED indication The LED on the ZDW120 will turn on when the load attached is ON. However, the LED can be user configured to turn ON when the load attached is OFF, if so desired, to act as a night light. The ZDW120 will flicker its LED when it is transmitting to any of its groups. This can be changed if desired. ADVANCED OPERATION All On/All Off The ZDW120 supports the ALL ON/ ALL OFF commands. The ZDW120 can be set to respond to ALL ON and ALL OFF commands 4 different ways.
PAGE 4
Night Light The LED on the ZDW120 will by default, turn ON when the load attached is turned ON. To make the LED turn ON when the load attached is turned OFF instead, set parameter 3 to a value of 1. • Parameter No: 3 • Length: 1 Byte • Valid Values = 0 or 1 (default 0) Invert Switch To change the top of the switch to OFF and the bottom of the switch to ON, set parameter 4 to 1.
PAGE 5
SPECIFICATIONS Power Signal (Frequency) Minimum Load Maximum Load Range 120 VAC, 60 Hz. 908.42 MHz. 40W, incandescent lamps only. 500W, incandescent lamps only. Up to 100 feet line of sight between the Wireless Controller and /or the closest HomePro Receiver Module. Operating Temperature Range 32-104O F (0-40O C). Indoor use only. INTER-OPERABILITY WITH Z-WAVE™ DEVICES A Z-Wave™ network can integrate devices of various classes, and these devices can be made by different manufacturers.