User Manual

ManualsBrandsAdvanced Control Technologies ManualsElectronicsWall Mounted Dimmer

Z-Wave ZDW103 Series 300, Rel. 3.10 Instructions

P/D 031510

HomePro

by ADVANCED CONTROL TECHNOLOGIES, INC.

0792-01

Z-Wave Radio Frequency (RF) Controlled, 500W, 120 VAC,

Wall Mounted Dimmer, Series 300, Release 3.10

ZDW103

ZDW103 WALL MOUNTED DIMMER

The ZDW103 Wall Mounted Dimmer is a component of the HomePro lighting control system. Wire the Wall Mounted

Dimmer in place of the standard wall switch according to the diagram above and program from the Wireless Controller

to operate loads. Inclusion of the ZDW103 Wall Mounted Dimmer on the ZTH100 Wireless Controller menu allows

remote ON/OFF control and dimming of lights connected.

This Wall Mounted Dimmer is designed to work with other Z-Wave enabled devices. Z-Wave nodes of other types

can be Included in the network and will also act as repeaters to increase the range of the network.

This product supports 40Kbps data transmission. This product can also be used for networking support in

systems that stream metadata. An example might include transmission of information from audio devices such as

song title, artist, and album information to various displays around the home.

DANGER! SHOCK HAZARD. Read and understand these instructions before installing. This device is intended for

installation in accordance with the National Electric code and local regulations in the United States, or the Canadian

Electrical Code and local regulations in Canada. It is recommended that a qualified electrician perform this installation.

There are no field repairable assemblies on this unit. If service is needed, the unit must be returned where purchased.

CAUTION: To reduce the risk of overheating and possible damage to other equipment, do not install

to control a receptacle, a motor operated appliance, a fluorescent lighting fixture, or a transformer-supplied

appliance, but only permanently installed incandescent lamp fixtures. Make sure the lamp(s) to be controlled

directly from the dimmer receiver total no more than 500 watts. Retain instructions for future use.

INSTALLATION

STEP 1. With power off, wire this ZDW103 according to the diagram show. Caution! Do not wire unit “live” (with

power on the circuit) and do not allow the yellow wire to contact line voltage, neutral or ground or you will

damage the device. If more than one ZDW103 is to be installed in a wall box, scored tabs on the side can

be broken off by bending back and forth with pliers, to accommodate proper fit. Apply power when completed.

HomePro

RF Home Automation

Supplied with matching

decorative switch plate

• This product supports Zensor Net Beam technology.

Note: This module must be “Included in the

Network” only where it will be permanently

installed. The proper operation of this node in the

mesh network is dependent on it knowing its

location with respect to other nodes. You cannot

“test bench” configure this module.

Summary of content (5 pages)

PAGE 1
HomePro RF Home Automation ZDW103 Z-Wave Radio Frequency (RF) Controlled, 500W, 120 VAC, Wall Mounted Dimmer, Series 300, Release 3.10 Supplied with matching decorative switch plate Note: This module must be “Included in the Network” only where it will be permanently installed. The proper operation of this node in the mesh network is dependent on it knowing its location with respect to other nodes. You cannot “test bench” configure this module. • This product supports Zensor Net Beam technology.
PAGE 2
Proper Single Gang Installation Using ZDW103’s standard full heat-sink (all tabs), the connected incandescent lamp load shall not exceed 500W. If a tab is removed from one side of the ZDW103 unit, the connected incandescent lamp load must not exceed 400W. If both tabs are removed from the ZDW103 unit, the connected incandescent lamp load must not exceed 300W. Proper Dual Gang Installation The connected incandescent lamp load must not exceed 400W for each of the two ZDW103 units.
PAGE 3
The ZDW103 will flicker its LED when it is transmitting to any of its groups. This can be changed if desired. Remote Control The ZDW103 will respond to BASIC and MULTILEVEL commands that are part of the Z-Wave system. Refer to your controller’s instructions as to whether your controller can transmit those commands. All On/All Off The ZDW103 supports the ALL ON/ ALL OFF commands. The ZDW103 can be set to respond to ALL ON and ALL OFF commands 4 different ways.
PAGE 4
Night Light The LED on the ZDW103 will by default, turn ON when the load attached is turned ON. To make the LED turn ON when the load attached is turned OFF instead, set parameter 3 to a value of 1. • Parameter No: 3 • Length: 1 Byte • Valid Values = 0 or 1 (default 0) Invert Switch To change the top of the switch to OFF and the bottom of the switch to ON, set parameter 4 to 1.
PAGE 5
SPECIFICATIONS Power 120 VAC, 60 Hz Maximum Load 500 Watts for control of permanently installed incandescent lamp fixtures only (not for control of receptacles) Signal (Frequency) 908.42 MHz Range Up to 100 feet line of sight between the Controller and /or the closest HomePro Receiver Module INTEROPERABILITY WITH Z-WAVE™ DEVICES A Z-Wave™ network can integrate devices of various classes, and these devices can be made by different manufacturers.