User Manual

ManualsBrandsAdvanced Control Technologies ManualsElectronicsWall Mounted Dimmer

Evolve Guest Controls LRM-20 Instructions

LRM-20

by Evolve Guest Controls

EvolveNet Radio Frequency (RF) Controlled, 500W, 120 VAC,

Wall Mounted Dimmer, Series 300, Release 3.10

The LRM-20 Wall Mounted Dimmer is a component of the HomePro lighting control system. Wire the Wall Mounted Dimmer

in place of the standard wall switch according to the diagram above and program from the Wireless Controller to operate

loads. Inclusion of the LRM-20 Wall Mounted Dimmer on the EHC-100 Wireless Controller menu allows remote ON/OFF

control and dimming of lights connected.

This Wall Mounted Dimmer is designed to work with other EvolveNet enabled devices. EvolveNet nodes of other types can

be Included in the network and will also act as repeaters to increase the range of the network. This product can also be used

for networking support in systems that stream metadata. An example might include transmission of information from audio

devices such as song title, artist, and album information to various displays around the home. Read and understand these

instructions before installing. This device is intended for installation in accordance with the National Electric code and local

regulations in the United States, or the Canadian Electrical Code and local regulations in Canada. It is recommended that a

qualiﬁed electrician perform this installation. There are no ﬁeld repairable assemblies on this unit. If service is needed, the

unit must be returned where purchased.to other equipment, do not install to control a receptacle, a motor operated appli-

ance, a ﬂuorescent lighting ﬁxture, or a transformer-supplied appliance, but only permanently installed incandescent lamp

ﬁxtures. Make sure the lamp(s) to be controlled directly from the dimmer receiver total no more than 500 watts. Retain

instructions for future use.

With power off, wire this LRM-20 according to the diagram show. Do not wire unit “live” (with power on the circuit) and

do notallow the yellow wire to contact line voltage, neutral or ground or you will damage the device. If more than

one LRM-20 is to be installed in a wall box, scored tabs on the side can be broken off by bending back and forth

with pliers, to accommodate proper ﬁt. Apply power when completed.

Supplied with matching decorative

switch plate

Note: This module must be “Included in the Network”

only where it will be permanently installed. The

proper operation of this node in the mesh network is

dependent on it knowing its location with respect to other

nodes. You cannot “test bench” conﬁgure this module.

LRM-20

Summary of content (5 pages)

PAGE 1
LRM-20 EvolveNet Radio Frequency (RF) Controlled, 500W, 120 VAC, Wall Mounted Dimmer, Series 300, Release 3.10 Supplied with matching decorative switch plate Note: This module must be “Included in the Network” only where it will be permanently installed. The proper operation of this node in the mesh network is dependent on it knowing its location with respect to other nodes. You cannot “test bench” configure this module.
PAGE 2
Proper Single Gang Installation Using LRM-20’s standard full heat-sink (all tabs), the connected incandescent lamp load shall not exceed 500W. If a tab is removed from one side of the LRM-20 unit, the connected incandescent lamp load must not exceed 400W. If both tabs are removed from the LRM-20 unit, the connected incandescent lamp load must not exceed 300W. Proper Dual Gang Installation The connected incandescent lamp load must not exceed 400W for each of the two LRM-20 units.
PAGE 3
The LRM-20 can be set to respond to ALL ON and ALL OFF commands 4 different ways. Refer to your controller for information on how to set the LRM-20 to operate in the manner you desire. Some controllers may be only able to set certain settings of ALL ON/ALL OFF response. The 4 different ways the LRM-20 can be setup to respond to ALL ON and ALL OFF commands are: • • • • LRM-20 will not respond to ALL ON or the ALL OFF command. LRM-20 will respond to ALL OFF command but will not respond to ALL ON command.
PAGE 4
using the controller to reset the node (on the EHC-100 select “SETUP” and scroll to “RESET UNIT”). Powerlevel The LRM-20 supports the Powerlevel command. The Powerlevel command allows controllers to set and get the RF transmit power level of a node and test specific links between nodes with specific RF transmit power. Refer to your controller’s instructions for more information if it supports this command.
PAGE 5
LRM-20 by Evolve Guest Controls Evolve Guest Controls LRM-20 Instructions