PROFESSIONAL SERIES Owner’s Guide For Model: CA SECRS Deluxe Vehicle Security and Remote Start System IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is applicable to most vehicles. However, due to the configuration of some vehicles, some functions AND/OR SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information. 2017 Voxx Electronics Corporation. All rights reserved.
Table of Contents Using Your Remote Control..................................................................... 3 Arming the Security System............................................................... 3 Passive Arming Bypass...................................................................... 3 Bypassing the Shock Sensor............................................................. 3 Hidden Alarm Function.......................................................................
Using Your Remote Control Arming the Security System To arm the system, exit the vehicle, close all doors, then press the button. The parking lights will flash 2 times, indicating the system is armed, has locked the doors (if equipped and connected) and activated the starter disable feature. The LED status indicator will blink steadily, once per second. NOTE: The system is equipped with a feature called Silent Choice.
Two Stage Door Unlock (Optional) If this feature is enabled on your system, pressing the button one time will unlock only the driver’s door. Press again within three seconds to unlock the remaining doors. Activating the Trunk Release Feature (Optional) If this feature is enabled on your system, pressing and holding the seconds will open the vehicle’s trunk or hatch.
Using the Progressive Car Finder Feature Press the button to locate your vehicle. The system will flash the parking lights and sound 5 times at low volume, increasing in volume each time the button is pressed. Using the Personal Protection Alarm (Panic) Press and hold the button for 3 seconds to activate the personal protection alarm. During panic mode, the normal function of the transmitter buttons will be suspended.
User Selectable LED This feature will control whether the LED is ON or OFF when the system is Armed/ Locked and can be toggled ON or OFF without entering the programming feature banks. 1. 2. Turn the ignition ON, OFF, ON, OFF. Press and release the valet/programming button 3 times. The system will respond with 1 chirp for ON or 2 chirps for OFF. Manually Overriding the Security System Your system can be disarmed without the use of the transmitter.
Using Your Remote Starter Remote Start Ready Mode must be enabled if your vehicle is equipped with a manual transmission. Remote Start Ready Mode - Manual Transmission Vehicles Only To activate the remote start function, the system must first be in Remote Start Ready Mode. Follow the steps below to enter remote start ready mode. 1. While the engine is running by the ignition key; a. Place the transmission in neutral. b. Set the parking brake 2.
Remote Starting Your Vehicle To activate the remote start function, press and release the button 2 times within 2 seconds. The system will sound, the parking lights will flash 1 time and the system will check the vehicle to ensure it is safe to start. If all safety parameters are correct, the vehicle will start. The vehicle’s parking lights will turn on (or flash depending on system settings) as a visual indication that the vehicle has started and is running.
Using the “Quick-stop” Feature If you want to make a short stop and keep your vehicle running (to keep the interior warm or cool), the quick-stop feature allows you to do this while keeping your vehicle secure and your keys with you. To engage Quick Stop: 1. Stop the vehicle and place the transmission in PARK. 2. With your foot off the brake pedal, press and release the button 2 times within 2 seconds. The LED will flash 3 times to confirm quick stop is entered. 3.
Preheating or Precooling the Vehicle’s interior Before exiting the vehicle, set the temperature controls to the desired setting and operation. After the system starts the vehicle, the heater or air conditioner will activate and heat or cool the vehicle’s interior to your setting. User Programmable Run Time / Run Time Extension The system has the ability to allow the user to extend the time the vehicle will be running under control of the remote start.
Operating the 2 / 3 Hour Start Up Timer Mode The system has the ability to start the vehicle every 2 or 3 hours for a 48 hour period. This feature is especially useful in cold climates where the only means to keep the engine and engine fluids warm is to periodically start the engine. The default setting is 3 hour, Selection between 2 or 3 hour is made in option programming. WARNING! Be certain that the vehicle is outdoors before using this or any remote starting device.
Operating the Daily Start Timer The system has the ability to start your vehicle based on a 24-hour countdown timer. This feature requires a two-part activation sequence. From the remote, while in range of the vehicle, pressing both the & buttons together will activate the 24 hour countdown timer (the vehicle will start 24 hours from this time). Next, When you are finished operating the vehicle for the day, perform the following steps to complete the process. 1.
Status LED, Light Flashes, and Siren/Horn Indications Status LED Flash Indications LED Flashes Function OFF Disarmed Slow Flash Armed Fast Flash Passive Arming Countdown ON (Solid) Valet Mode 2 Flashes Zone 2 Trigger, Hood / Trunk 3 Flashes Zone 3 Trigger, Door 4 Flashes Zone 4 Trigger, Shock Sensor 5 Flashes Zone 5 Trigger, Ignition Siren/Horn Chirp Indications Chirps 1 Function Disarm 2 A
Optional 2-Way LED Remote Control Optional 2 Way LED Remote Control Notifications / Responses The 2 Way LED remote control responses outlined below are in addition to the normal beep/LED flash that takes place upon pressing the buttons of the remote control.
Optional 2-Way LCD Remote Control Additional Features of the Optional 2 Way LCD Remote Control Check Vehicle Status Press and release 2 times then press display the current status of the vehicle. within 3 seconds, the transmitter will Display Illumination Press and hold the button for 1 second. The display will illuminate for 5 seconds.
Button Lock Press and release then press hold the for 2 seconds to toggle the button lock on or off. When the button lock is active, the remote control will beep/vibrate 2 times when a button is pressed indicating it is locked. Illumination Press and release 2 times then press and hold for 2 seconds to toggle illumination on or off. When on, the display will illuminate when it receives or sends a command.
LCD Remote Control ICON’s LOCK UNLOCK SYSTEM ARMED VALET MODE TRANSMITTING IGNITION ON/TRIGGER TRUNK TRIGGER DOOR TRIGGER HOOD TRIGGER FULL SHOCK TRIGGER SYSTEM TRIGGER TIME COUNT DOWN BATTERY INDICATOR BATTERY SAVE MODE VIBRATE/SILENT MODE MELODY MODE 2 CAR MODE TIME DISPLAY ALARM CLOCK ENGINE RUNNING TIMER / TEMP. START MODES AUX MODE AUX 1 OUTPUT AUX 2 OUTPUT AUX 3 OUTPUT AUX 4 OUTPUT AUX 5 OUTPUT 2017 Voxx Electronics Corporation. All rights reserved.
Remote Control Buttons & Functions 4-Button Transmitter Lock Lock Unlock Car Find / Panic Start X Operation Method Press and Release Unlock X Press and Release 2 Step Unlock X Press and Release 2 times Trunk X Push and Hold (3 Sec) Car Finder X Press and Release Panic X Push and Hold (3 Sec) Remote Start X Press and Release (1 or 2 times depending on selectable option) Remote Start Shutdown X Push and Hold (3 Sec) Run Time Extention X Press and Release 4 times.
LCD 5-Button Transmitter Lock Lock Unlock Car Find / Panic Start Function Operation Method X Press and Release Unlock X Press and Release 2 Step Unlock X Press and Release 2 times Trunk X Push and Hold (3 Sec) Car Finder X Press and Release Panic X Push and Hold (3 Sec) Remote Start X Press and Release (1 or 2 times depending on selectable option) Remote Start Shutdown X Push and Hold (3 Sec) Run Time Extention X Press and Release 4 times.
Replacing Remote Control Batteries 4 Button Remote Control - Model CAT4M & CATMLED The batteries inside each remote control should last approximately 1 year for the CAT4M and 6 Months for the CATMLED under normal use. When the batteries become weak you will notice the remote control range (the distance from the vehicle the remote control will work) deteriorate and the small LED on the remote control will dim.
LIMITED LIFETIME WARRANTY Applies to Code Alarm Series Control Modules, Sirens, Sensors, and Relays.
caSECRS Owners revA
2017 Voxx Electronics Corporation. All rights reserved.
Voxx Electronics Corporation. Customer Service 1-800-421-3209 WWW.CODE-ALARM.COM FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including any interference that may cause undesired operation.