PROFESSIONAL SERIES Owner’s Guide For Models: ca6154 Deluxe Vehicle Security and Remote Start System IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is applicable to most vehicles. However, due to the configuration of some vehicles, some functions AND/OR SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information. 2014 Voxx Electronics Corporation. All rights reserved.
Table of Contents Using Your Remote Control..................................................................... 3 Arming the Security System............................................................... 3 Passive Arming Bypass...................................................................... 3 Bypassing the Shock Sensor............................................................. 3 Hidden Alarm Function.......................................................................
Using Your Remote Control Arming the Security System To arm the system, exit the vehicle, close all doors, then press the button. The parking lights will flash 2 times, indicating the system is armed, has locked the doors (if equipped and connected) and activated the starter disable feature. The LED status indicator will blink steadily, once per second. NOTE: The system is equipped with a feature called Silent Choice.
Two Stage Door Unlock (Optional) If this feature is enabled on your system, pressing the button one time will unlock only the driver’s door. Press again within three seconds to unlock the remaining doors. Activating the Trunk Release Feature (Optional) If this feature is enabled on your system, pressing and holding the seconds will open the vehicle’s trunk or hatch.
Valet Mode When valet mode is activated the status LED will light solid, and all security functions will be disabled. To enter or exit valet mode simply follow the 4 steps outlined below: 1. Turn the vehicle’s ignition ON. 2. Push and hold the programming/valet button. 3. The LED will turn on solid when valet mode is active 4. Release the programming/valet button.
Car Jack Mode This feature must be turned on in system programming, please consult your installing dealer. Triggering Car Jack mode: While the ignition is ON and press and hold + seconds, the parking lights will flash 1 time and the system will act as follows; for 2 1. 50 seconds after being triggered the siren will chirp for 15 seconds, during this 15 seconds you will be alerted to push the valet button to turn off Car Jack mode.
Using Your Remote Starter Remote Start Ready Mode must be enabled if your vehicle is equipped with a manual transmission. Remote Start Ready Mode - Manual Transmission Vehicles Only To activate the remote start function, the system must first be in Remote Start Ready Mode. Follow the steps below to enter remote start ready mode. 1. While the engine is running by the ignition key; a. Set the parking brake b. Place the transmission in neutral. 2.
Remote Starting Your Vehicle To activate the remote vehicle start function, press and release the button 2 times within 2 seconds. The system will sound, the parking lights will flash 1 time and the system will check the vehicle to ensure it is safe to start. If all safety parameters are correct, the vehicle will start within 5 seconds. The vehicle’s parking lights will turn on (or flash depending on system settings) as a visual indication that the vehicle has started and is running.
User Programmable Run Time / Run Time Extension The system has the ability to allow the user to extend the time the vehicle will be running under control of the remote start. This will only extend the run time back to the current run time setting during the current remote start cycle. If your system is set to run 15 minutes and the time remaining is 4 minutes, extending the run time will reset the countdown timer to 15 minutes and your vehicle will continue to run for another 15 minutes.
To begin the 2 / 3 hour start up timer mode: 1. Turn the vehicle’s ignition ON then OFF. 2. Press and hold the valet button. 3. Press the button 4 times, the system will; a. When set for 3 Hour (default) - chirp 2 times and flash the parking lights 4 times. b. When set for 2 Hour - chirp 1 time and flash the parking lights 2 times. 4. Release the valet button. To exit the 2 / 3 hour start up timer mode: 1. OR 1. Turn the vehicle’s Ignition ON.
Operating the Daily Start Timer The system has the ability to start your vehicle based on a 24-hour countdown timer. This feature requires a two-part activation sequence. From the remote, while in range of the vehicle, pressing both the & buttons together will activate the 24 hour countdown timer (the vehicle will start 24 hours from this time). Next, When you are finished operating the vehicle for the day, perform the following steps to complete the process. 1.
LED and Siren/Horn Indications LED Display Indications LED Function OFF DISARMED SLOW FLASH ARMED FAST FLASH PASSIVE ARMING ON (SOLID) VALET MODE 2 FLASH... PAUSE ZONE 2 TRIGGER, HOOD/TRUNK 3 FLASH... PAUSE ZONE 3 TRIGGER, DOOR 4 FLASH... PAUSE ZONE 4 TRIGGER, SHOCK 5 FLASH...
Transmitter Button Functions 1 Way Transmitter Lock Lock Unlock Car Find / Panic Start X Operation Method Press and Release Unlock X Press and Release 2 Step Unlock X Press and Release 2 times Trunk X Push and Hold (3 Sec) Car Finder X Press and Release Panic X Push and Hold (3 Sec) Remote Start X Press and Release (1 or 2 times depending on selectable option) Remote Start Shutdown X Push and Hold (3 Sec) Run Time Extention X Press and Release 4 times.
Replacing Remote Control Batteries 1 Way 4 Button Remote Control - Model CAT4 The batteries inside each remote control should last approximately 1 year under normal use. When the batteries become weak you will notice the remote control range (the distance from the vehicle the remote control will work) deteriorate and the small LED on the remote control will dim. To replace the remote control batteries: 1. Using a coin, disassemble the halves of the remote control. 2.
Code Systems, Inc. Limited Lifetime Warranty Code Systems Inc.
Voxx Electronics Corporation. Customer Service 1-800-421-3209 WWW.CODE-ALARM.COM FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including any interference that may cause undesired operation.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.