User's Manual

ManualsBrandsAdvance Security ManualsElectronicsAuto Alarm System Receiver

00/04/21

MODEL 6974

REMOTE CONTROL AUTO ALARM SYSTEM

INSTALLATION & OPERATION INSTRUCTIONS

Override Plug

L.E.D. Plug

4 pin shock sensor

11 Pin Plug

Antenna Plug

1. Blue/yellow (N/O)--unlock.

2. Blue/red (N/C)--unlock.

3. Blue/white (Com)--unlock.

4. Green/white (Com)--lock.

5. Green/yellow (N/O)--lock.

6. Green/red (N/C)--lock.

Negative door lock.

Green/white

Blue/white

Green/yellow

Blue/yellow

Positive door lock.

Green/white

Blue/white

Green/yellow

Blue/yellow

Door lock Door unlock

Master

locking

switch

locking

Master

switch

+12V

Door lock Door unlock

+12V

10 Pin main harness

2 wires start cut

3 A Fuse

Red Wire: +12V To Fuse Box

Brown Wire: To Siren

Black Wire: To Ground

Gray Wire:Channel 2 (Trunk release) power



Red / White Wire: Parking light power

Parking light

Yellow Wire: To I

nition Switch

+12

White wire :Parkin

ht Out

Light green wire :Dome Light Output

Light green wire :Dome Light power

10A Fuse

Entry illumination

Connect to +12V for + switch

or to ground for - switch

Existing door pin switch

Dome Light

Trunk release

Connect to +12V for + switch

or to ground for - switch

Gra

Wire:Channel 2

(

Trunk release

)

out

Connect to active

trunk release button

Summary of content (10 pages)

PAGE 1
00/04/21 MODEL 6974 REMOTE CONTROL AUTO ALARM SYSTEM INSTALLATION & OPERATION INSTRUCTIONS Antenna Plug 4 pin shock sensor 10 Pin main harness 11 Pin Plug 1. Blue/yellow (N/O)--unlock. 2. Blue/red (N/C)--unlock. 3. Blue/white (Com)--unlock. 4. Green/white (Com)--lock. 5. Green/yellow (N/O)--lock. 6. Green/red (N/C)--lock. L.E.D. Plug Override Plug 2 wires start cut Negative door lock. Green/white Master locking switch Blue/white Door lock Green/yellow Positive door lock.
PAGE 2
Violet Wire: Positive Door Pin Switch +12V Green W ire Negative Door Pin Switch: +12V Blue Wire: Instant Trigger Ground Input Red Wire: (-) 200mA channel 4 output Gray W ire: (-) 200mA two step door unlock output N.O. circuit block White Wire: (-) 200mA horn output Cut 85 30 Pink W ire: (-) 200mA headlight output 86 87a 87 Yellow Wire: (-) 200mA channel 3 output N.C.
PAGE 3
Press button 3 to program channel 3, 3 short chirps and LED on to confirm programmed and ready program channel 4. Press button 4 to program channel 4, 4 short chirps and LED on to confirm programmed rd Program 3 transmitter, push valet switch one time again, the LED will with three flashes…pause sequence. Use above steps to program each channel. th Program 4 transmitter, push valet switch one time again, the LED will with four flashes…pause sequence. Use above steps to program each channel. 3.
PAGE 4
During programming, if you don’t respond to previous step in 15 seconds, or any time press transmitter’s button 1, it will exit features programming, which indicates by 3 long chirps.
PAGE 5
TEST shock sensor: 1. Use channel 2 to enter. (press button 2) 2. There will be a long chirp confirmation for you to test shock sensor. 3. Activate the warn away (first stage shock sensor), system will emit a short chirp. 4. Activate the full alarm (second stage shock sensor), system will emit a long chirp. 5. Continue to test the shock sensor until reach the proper sensitivity. TEST current sensor: 1. Use channel 3 to enter. ( press button 3) 2. There will be a long chirp confirmation. 3.
PAGE 6
Button 1 + 2 both Button 1 + 2 both 1 sec Button 2 + 3 both Side button For auto channel setting: Transmitter Button Button 1 Button 1 Button 1 - 1 Button 2 Button 2 -2 Button 3 Button 3 - 3 Button 3 - 3 Button 1 + 3 both Button 4 Button 1 + 2 both Button 1 + 2 both 1 sec. Button 2 + 3 both Side button Silent arm/disarm Activate car-jacking Ignition in "off" position.
PAGE 7
D. CHIRP INDICATORS : Chirp Function 1 chirp Arm 2 chirps Disarm 3 chirps Defective reminder 4 chirps Disarm / Triggered 6 chirps Car locator E. PARKING LIGHT : Parking light Function 1 flash Arm 2 flashes Disarm 3 flashes Disarm / Triggered 5 flashes Transmitter low battery. (suitable for random code only) 12 flashes Car locator F. OVERRIDE/VALET SWITCH : 1. OVERRIDE FUNCTION: (System in arm condition) Use in emergency, like lost or malfunctions of transmitter.
PAGE 8
I. ACTIVE DISARMING : 1. Press disarm button on the transmitter. 2. The siren will chirp twice to indicate that system disarmed. NOTE: 1. Tamper disarming: If alarm triggered, upon disarm the system, siren chirp 4 times,parking light flash 3 times. NOTE: 2. Automatic re-arm: No doors open and no ignition on after disarm; after 60 seconds system auto rearm. J. PANIC FUNCTION : The transmitter can be used as a remote panic switch to manually trigger the alarm in case emergency.
PAGE 9
Note: If you use password (see below Password Security) to double protect the vehicle security, you will need to use it to completely disarm the system. N. PASSWORD SECURITY : In carry this feature you need to set features programming of password 'ON' first. Then program your password number. Please see above PROGRAMMING section. Using password to protect system. Below is an example of how to use password to completely disarm system. System in arm condition. 1. Open the door, siren will sound. 2.
PAGE 10
Upon first disarming, the system only unlock the driver's side door. Then press the disarm button again, the system will unlock all the doors. U. ALARM OPERATING CONDITION: Siren, horn Parking Light 1. Arming 2. Disarming 1 Chirp 2 or 4 Chirps 1 Flash 2 or 3 Flashes 3. 4. 5. 6. Alarming Alarming Alarming 6 chirps Flashes Flashes Flashes 12 flashes Trigger Panic Car-Jacking Car locator LED Doors Slow flash Locking Fast flash (in passive arming) or Unlocking OFF.