User Manual CDM531AM WiFi Mobile Router ZALiP 1
IMPORTANT USAGE INSTRUCTION For the convenience of use, this product accepts power from a desktop or a laptop computer. It’s mandatory to connect both of two USB connectors at one end of USB supplied power cable to computer at one time. Power supply is not sufficient for the device to operate normally if only one USB connector is inserted into the computer. In this scenario it might cause temporary malfunction on the computer.
Copyright The contents of this publication may not be reproduced in any part or as a whole, stored, transcribed in an information retrieval system, translated into any language, or transmitted in any form or by any means, mechanical, magnetic, electronic, optical, photocopying, manual, or otherwise, without the prior written permission. Trademarks All products, company, brand names are trademarks or registered trademarks of their respective companies. They are used for identification purpose only.
Table of contents IMPORTANT USAGE INSTRUCTION...................................................................................... 2 COPYRIGHT ............................................................................................................................. 3 FCC INTERFERENCE STATEMENT ....................................................................................... 3 CHAPTER 1 INTRODUCTION ............................................................................................. 5 1.
Chapter 1 Introduction Congratulations on your purchase of this outstanding Productʳ ˖CDM531 Wi-Fi Mobile Router. This product is specifically designed for mobile user who needs to have the internet access beyond his home and office. It provides a complete solution for Internet surfing and broadband sharing. Instructions for installing and configuring this product can be found in this manual.
1.
LED indicators USB LED Wi-Fi LED LED color Description Blue Blue in flash Blue Blue in flash Blue in fast flash 3G/3.5G is on Data access WLAN is ON Data access Device is in WPS Mode Installation Steps DO NOT switch on WiFi Mobile Router before performing the installation steps below. Step 1. Turn off the power switch and then plug USB 3G Modem to the Router. Note: The Wi-Fi Mobile Router is designed to work with either UMTS or EV-DO and even HSUPA 3G modem.
Step 4. 4.1. Use Power Adapter Then plug the other end of the power adapter into a wall outlet. 4.2. Use USB Cable Then plug the other end of USB Cable to USB Port on your PC or NB. Step 5. Turn on the power switch. The Wi-Fi and 3G LED will turn ON to indicate that the power has been applied.
Chapter 2 Getting start 2.1 Easy Setup Utility by Easy Setup We provide Wizard and Easy Setup by Windows Utility to enable you to set up the WiFi Mobile Router quickly and easily. Check the steps below before running the section. (1) Press WPS button more than 6 seconds on the Router. The Router will reset to default. (2) Connect to the Router by Wi-Fi. The default SSID is the same as “Mac Address” (3) Insert CD to CDROM; Click the Easy Setup Utility from CD or Auto Run.
Step 3. 1. Please select Wizard mode to run the setup step-by-step to diagnose the network settings of the Router. 2. Click the “Wizard” button and click “NEXT” to continue. Step 4. 1. Make sure your USB 3G Modem is connected to the USB port of the Router. 2. Make sure the Router is powered on. 3. Make sure your computer has connected to the Router. 4. Make sure your computer has an IP address. 5. Click “Next” to continue. Step 5. 1.
Step 6-1. Select “Auto-Detection”, and the Utility will try to detect and configure the required 3G service settings automatically. Click “Next” to continue. ʳ ϡʳ Default PIN Code is empty, if you have PIN Code, you must enter it. For example “0000”. If no, just Click “Next” to continue. Step 6-2. Or you can select “Manual” and manually fill in the required 3G service settings provided by your ISP. Click “Next” to continue. Step 7. Check the settings, and then click the “Next” if the settings are correct.
Step 8. The Wi-Fi Mobile Router is rebooting to make your entire configuration activated. Step 9. Please reconnect to Router before click “Next”. Step 10-1. Click “Next” to test the Internet connection or you can skip test. And then click “Next” to continue.
Step 10-2. Test the Internet connection Step 11. Congratulations! Setup is completed. Now you have already connected to Internet successfully.
2.2 Easy Setup by Configuring Web Pages You can also browse web UI to configure the device. Browse to Activate the Setup Wizard Please type in the IP Address (http://192.168.123.254) Please type “admin” in the Password and click ‘login’ button. Select your language. Select “Wizard” for basic settings with simple way.
Press “Next” to start the Setup Wizard. Configure with the Setup Wizard Step 1: Change System Password. Set up your system password. (Default˖admin) Step 2˖ Select Time Zone.
Step 3˖Select Wan Type. If you want to use 3G service as the main internet access, please set the WAN interface as “Wireless WAN” and the WAN type as “3G”. Step 4˖ Select “Auto Detection” Dial-up Profile, and the Utility will try to detect and configure the required 3G service settings automatically. Or you can select “Manual” and manually fill in the required 3G service settings provided by your ISP. Default PIN Code is empty, if you have PIN Code, you must enter it. Step 5: Set up your Wireless Network.
Step 6˖Set up Wireless Security. Set up your Authentication and Encryption. Step 7: Apply your Setting. Then click Apply Setting. Step 8: Click Finish to complete it.
Chapter 3 Making Configuration 3.1 Advanced 3.1.1 Basic Setting Network Setup LAN Setup 1. LAP IP Address: the local IP address of this device. The computers on your network must use the LAN IP address of your product as their Default Router. You can change it if necessary. 2. Subnet Mask: insert 255.255.255.
Internet Setup This device supports different WAN types of connection for users to connect to remote wireless ISP, such as 3G (WCDMA, HSxPA, HSPA+, CDMA2000, EV-DO, TD-SCDMA), iBurst, or Wi-Fi Hotspot. Note. Users need to insert USB modem card for 3G and iBurst WAN connections. 3G WAN Types: The WAN fields may not be necessary for your connection. The information on this page will only be used when your service provider requires you to enter a User Name and Password to connect with the 3G network.
provider. 8. Account: Enter the new User Name for your PC card here, you can contact to your ISP to get it. 9. Password: Enter the new Password for your PC card here, you can contact to your ISP to get it. 10. Authentication: Choose your authentication. 11. Primary DNS: This feature allows you to assign a Primary DNS Server, contact to your ISP to get it. 12. Secondary DNS: This feature allows you to assign a Secondary DNS Server, you can contact to your ISP to get it. 13.
1. Account: Enter the new User Name for your PC card here, you can contact to your ISP to get it. 2. Password: Enter the new Password for your PC card here, you can contact to your ISP to get it. 3. Primary DNS/Secondary DNS: Optional, This feature allows you to assign a DNS Servers 4. Connection Control: There are 3 modes to select: Connect-on-demand: The device will link up with ISP when the clients send outgoing packets.
Step 2: After finish searching, it will list all available Wi-Fi APs in your environment. You can select one of the lists to start to connect, or press “Refresh” button to search again. Step 3: Click “Save” button to save settings after selecting. There will be a field here for you to input encryption key if remote Wi-Fi Hotspot or Wi-Fi AP requires. Step 4: Click “Reboot” button to restart device to take new settings effective.
DHCP Server Press “More>>” for more options, 1. DHCP Server: Choose either Disable or Enable 2. Lease Time: DHCP lease time to the DHCP client 3. IP Pool Starting/Ending Address: Whenever there is a request, the DHCP server will automatically allocate an unused IP address from the IP address pool to the requesting computer. You must specify the starting / ending address of the IP address pool 4. Domain Name: Optional, this information will be passed to the client 5.
DHCP Clients List The list of DHCP clients shows here. DHCP Fixed Mapping The DHCP Server will reserve the special IP for special MAC address, shows below.
Wireless Settings Wireless settings allow you to set the wireless configuration items. 1. Wireless Operation Mode: Choose AP mode or Client mode. The factory default setting is AP mode. 2. Network ID (SSID): Network ID is used for identifying the Wireless LAN (WLAN). Client stations can roam freely over this product and other Access Points that have the same Network ID. (The factory setting is “default”) 3.
6. Authentication mode: You may select from nine kinds of authentication to secure your wireless network: Open, Shared, Auto, WPA-PSK, WPA2-PSK, and WPA-PSK/WPA2-PSK. Open Open system authentication simply consists of two communications. The first is an authentication request by the client that contains the station ID (typically the MAC address). This is followed by an authentication response from the AP/router containing a success or failure message.
WPS (Wi-Fi Protection Setup) WPS is Wi-Fi Protection Setup which is similar to WCN-NET and offers safe and easy way in Wireless Connection. Wireless Client List The list of wireless client is shows here. Change Password You can change Password here. We strongly recommend you to change the system password for security reason.
3.1.
Packet Filter includes both outbound filter and inbound filter. And they have same way to setting. Packet Filter enables you to control what packets are allowed to pass the router. Outbound filter applies on all outbound packets. However, inbound filter applies on packets that destined to Virtual Servers or DMZ host only. You can select one of the two filtering policies: 1. Allow all to pass except those match the specified rules 2.
URL Blocking URL Blocking will block LAN computers to connect with pre-define Websites. The major difference between “Domain filter” and “URL Blocking” is Domain filter require user to input suffix (like .com or .org, etc), while URL Blocking require user to input a keyword only. In other words, Domain filter can block specific website, while URL Blocking can block hundreds of websites by simply a keyword. 1. URL Blocking Enable Check if you want to enable URL Blocking. 2.
MAC Control MAC Address Control allows you to assign different access right for different users and to assign a specific IP address to a certain MAC address. 1. MAC Address Control Check “Enable” to enable the “MAC Address Control”. All of the settings in this page will take effect only when “Enable” is checked. 2. Connection control Check "Connection control" to enable the controlling of which wired and wireless clients can connect with this device.
Miscellaneous 1. Administrator Time-out The time of no activity to logout automatically, you may set it to zero to disable this feature. 2. Remote Administrator Host/Port In general, only Intranet user can browse the built-in web pages to perform administration task. This feature enables you to perform administration task from remote host. If this feature is enabled, only the specified IP address can perform remote administration. If the specified IP address is 0.0.0.
3.1.3 Advanced Settings Status System Log This page supports two methods to export system logs to specific destination by means of syslog (UDP) and SMTP (TCP). The items you have to setup including: IP Address for Syslogd Host IP of destination where sys log will be sent to. Check Enable to enable this function. Setting of Email alert Check if you want to enable Email alert (send syslog via email). Check Enable to enable this function.
SMTP Server IP and Port Input the SMTP server IP and port, which are connected with ':'. If you do not specify port number, the default value is 25. For example, "mail.your_url.com" or "192.168.1.100:26". SMTP Username and password Input a user account and password for the SMTP server. E-mail address The recipients who will receive these logs, you can assign more than 1 recipient, using ';' or ',' to separate these email addresses. E-mail Subject The subject of email alert, this setting is optional.
3.1.4 TOOL BOX System Info You can view the System Information and System log, and download/clear the System log, in this page.
Firmware Upgrade You can upgrade firmware by clicking “Upgrade” button. Backup Setting You can backup your settings by clicking the “Backup Setting” button and save it as a bin file. Once you want to restore these settings, please click Firmware Upgrade button and use the bin file you saved.
Reset to Default You can also reset this product to factory default by clicking the Reset to default button. Reboot You can also reboot this it by clicking the Reboot button. Miscellaneous Domain Name or IP address for Ping Test Allow you to configure an IP, and ping the device. You can ping a specific IP to test whether it is alive.
Chapter 4 Troubleshooting This Chapter provides solutions to problems for the installation and operation of the WiFi Mobile Broadband Router. You can refer to the following if you are having problems. 1 Why can’t I configure the router even the cable is plugged and the LED is lit? Do a Ping test to make sure that the WiFi Mobile Broadband Router is responding. Note: It is recommended that you use an Ethernet connection to configure it Go to Start > Run. 1. Type cmd. 2. Press OK. 3.
2 What can I do if my Ethernet connection does not work properly? A. Make sure the RJ45 cable connect with the router. B. Ensure that the setting on your Network Interface Card adapter is “Enabled”. C. If settings are correct, ensure that you are not using a crossover Ethernet cable, not all Network Interface Cards are MDI/MDIX compatible, and use a patch cable is recommended. D. If the connection still doesn’t work properly, then you can reset it to default. 3 Problems with 3G connection? A.
4 Something wrong with the wireless connection? A. Can’t setup a wireless connection? I. Ensure that the SSID and the encryption settings are exactly the same to the Clients. II. Move the WiFi Mobile Broadband Router and the wireless client into the same room, and then test the wireless connection. III. Disable all security settings such as WEP, and MAC Address Control. IV. Turn off the WiFi Mobile Broadband Router and the client, then restart it and then turn on the client again. V.
5 What to do if I forgot my encryption key? 1. Go back to advanced setting to set up your Encryption key again. 2. Reset the WiFi Mobile Broadband Router to default setting 6 How to reset to default? 1. Ensure the WiFi Mobile Broadband Router is powered on 2. Find the Reset button on the right side 3. Press the Reset button for 8 seconds and then release. 4. After the WiFi Mobile Broadband Router reboots, it has back to the factory default settings.
Appendix A Spec Summary Table WiFi Mobile Router Device Interface Wireless WAN WPS/Reset Button LED Indication Power Switch Power Jack Wireless LAN (WiFi) Standard SSID Channel Security WPS Functionality 11b/g/n ZALiP USB 2.0 for external HSPA modem For WPS connection / Reset router setting to factory default USB / WiFi Slide ON/OFF switch mini-usb Power Jack, CDM531AM ƽ ƽ ƽ DC 5V/1.2A ƽ ƽ IEEE 802.
Appendix B Licensing information This product includes copyrighted third-party software licensed under the terms of the GNU General Public License. Please refer to the GNU General Public License below to check the detailed terms of this license. The following parts of this product are subject to the GNU GPL, and those software packages are copyright by their respective authors. Linux-2.6.21 system kernel busybox_1.3.2 bridge-utils 0.9.5 dhcpcd-1.3 ISC DHCP V2 P5 IPtables 1.4.
GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc. 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it.
GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License.
3.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices.
פ܅ሽंᘿ୴ࢤሽᖲጥᙄऄ รԼԲයʳ ীڤᎁᢞٽհפ܅୴᙮ሽᖲΔॺᆖױΔֆΕᇆࢨ ࠌ݁ृشլᖐ۞᧢ޓ᙮ΕףՕפࢨ᧢ޓૠհࢤ ֗פ౨Ζ รԼයʳ פ܅୴᙮ሽᖲհࠌشլᐙଆڜ٤֗եឫٽऄຏ ॾΙᆖ࿇ڶեឫွழΔᚨܛمೖشΔࠀޏ۟ྤեឫழ ֱᤉᥛࠌشΖ ছႈٽऄຏॾΔਐࠉሽॾऄࡳ܂ᄐհྤᒵሽຏॾΖ פ܅୴᙮ሽᖲႊٽ࠹ݴऄຏॾࢨՠᄐΕઝᖂ֗᠔᛭شሽं ᘿ୴ࢤሽᖲໂհեឫΖ END OF TERMS AND CONDITIONS 48
For Mobile Configuration IMPORTANT NOTE: For Portable Configuration Federal Communication Commission (FCC) Radiation Exposure Statement This EUT is compliance with SAR for general population/uncontrolled exposure limits in ANSI/IEEE C95.1-1999 and had been tested in accordance with the measurement methods and procedures specified in OET Bulletin 65 Supplement C.
