61280.
PAGE II 61280.003L1-1B RADIO FREQUENCY INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for an intentional radiator, pursuant to Part 15, Subpart C of the FCC Rules. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause interference to radio communications. The limits are designed to provide reasonable protection against such interference in a residential situation.
61280.003L1-1B PAGE III EXPOSURE TO RADIO FREQUENCY FIELDS This device is designed to provide a maximum power output of 100 mW. This level of RF energy in itself is below the Maximum Permissible Exposure (MPE) levels specified in FCC OET 65:97-01. The installation of high gain antenna equipment in the system configuration may create the opportunity for exposure to levels higher than recommended for the general population at a distance less than one meter from the center of the antenna.
PAGE IV 61280.
61280.003L1-1B PAGE V INSTALLATION CONTENTS PAGE SECTION 1 TRACER DESCRIPTION ..................................................... 1 INTRODUCTION .............................................................. 1 ISM BAND SPREAD SPECTRUM ................................... 1 APPLICATIONS ............................................................... 2 SPREAD SPECTRUM ........................................................ 2 Direct Sequence ...........................................................
PAGE VI 61280.003L1-1B LINK PLANNING ........................................................... 19 ANTENNA FEEDLINE LOSS ......................................... 20 ANTENNA GAIN ......................................................20 PATH LOSS .......................................................... 21 PATH AVAILABILITY ................................................. 21 SETTING THE TRANSMITTER POWER ................................... 22 SETTING THE RFC FREQUENCY PLAN ..............................
61280.003L1-1B SECTION 4 PAGE VII TROUBLESHOOTING ....................................................... 37 GENERAL .................................................................. 37 PROBLEM DESCRIPTIONS AND RECOMMENDED ACTIONS ........... 38 TROUBLESHOOTING USING THE FRONT PANEL INDICATORS ..... 38 “Link Error” light is lit, or link is down ...................... 38 “BPV” light on T1-A or B is lit .................................... 39 RED light on T1-A or B is lit .................................
PAGE VIII GLOSSARY 61280.003L1-1B ............................................................................. 55 ACRONYMS USED IN THIS MANUAL .................................... 55 APPENDIX A CABLE CONNECTIONS ................................................... A-1 TERMINAL CONNECTION (DB25) .................................... A-1 PERSONAL COMPUTER CONNECTION (DB9) ....................... A-1 MODEM CONNECTION (DB25) ...................................... A-2 APPENDIX B FCC REGULATIONS ..............
61280.003L1-1B PAGE IX ILLUSTRATIONS 1-1. Typical Application ......................................... 2 1-2. Bandwidth Division ........................................ 3 1-3. BBP ................................................................ 6 1-4. BBP Rear Panel ............................................. 6 1-5. BBP Block Diagram ....................................... 7 1-6. BBP Front Panel (with door closed) .............. 9 1-7. BBP Front Panel (with door open) ................. 9 1-8.
PAGE X 61280.
61280.003L1-1B PAGE 1 SECTION 1 TRACER DESCRIPTION INTRODUCTION The Tracer provides dual T1 transport by way of a spread spectrum microwave link for distances up to 20 miles or more depending on path engineering. System performance is determined, in part, by the engineering of the microwave link. Each end of a Tracer link is composed of two units -- the baseband processor (BBP) and the radio frequency converter (RFC).
PAGE 2 SECTION 1 61280.003L1-1B APPLICATIONS Any application that would typically use metallic T1 as a transport can use the Tracer instead. The figure below illustrates a typical application.
61280.003L1-1B PAGE 3 TRACER DESCRIPTION DIRECT SEQUENCE A direct sequence transmitter spreads the signal by mixing the data with the output of a pseudorandom number generator which changes state at a rate higher than the data rate. This rate is called the “chipping” rate. The Tracer chipping rate is twelve times the data rate. CODING Many different pseudorandom sequences exist.
PAGE 4 SECTION 1 61280.003L1-1B The transmitter at one end (TxA) of a link will transmit in the lower half of the spectrum. Consequently the receiver at the other end will receive in the lower half of the band and transmit in the upper half. Thus, a system will operate in one of two frequency plans -- transmit in the upper and receive in the lower or vice versa. These two plans are called Plan A and Plan B. One end of a path will be on Plan A and the other will be on Plan B.
61280.003L1-1B PAGE 5 TRACER DESCRIPTION For the T1 receiver to operate correctly, a minimum number of “1s” must exist on the T1 facility. If the data cannot be guaranteed to meet this requirement, then another line coding format is used. In the bipolar 8 zero substitution (B8ZS) scheme, a string of eight “0s” is replaced by a special sequence of eight bits that contains a bipolar violation. The receiver, upon recognizing this sequence, reinserts the eight “0s” and the data is recovered intact.
PAGE 6 SECTION 1 61280.003L1-1B Tracer SYSTEM CONFIGURATION A Tracer system is composed of three major subsystems -- a baseband processor, a radio frequency convertor, and an antenna. The following section describes the system components. BASEBAND PROCESSOR OR BBP The BBP (ADTRAN part number 1280.003L1) is a 1-U, 19" rackmountable unit that provides the system electrical interfaces, user controls and indicators, and performs the spread spectrum processing for the system.
61280.003L1-1B PAGE 7 TRACER DESCRIPTION The interfaces are illustrated in the BBP Block Diagram below. The functions of the BBP are partitioned into three printed circuit boards or PCBs, all contained in the same enclosure. RS-232 UART T1A T1 Baseband Processor Board µC T1C Multiplex T1B Spread Spectrum Data Pump Viterbi Encoder/ Decoder T1 Fc = 140 MHz IF Filter Σ DSP 90 Fc = 70 MHz 90 IF Interface Board -48Vdc Figure 1-5.
PAGE 8 SECTION 1 61280.003L1-1B For connections to other CPE-type equipment, such as an ADTRAN TSU-100, a straight-through T1 cable is provided by ADTRAN (part number 3127.004) and is included with the BBP. VT-100 RS-232 INTERFACE A serial interface port using RS-232C signal levels is provided for attaching a VT-100-compatible terminal. The connection is made via a DB-25 connector on the rear panel. The data rate is configured for 9600 bps, 8 data bits, no parity, and 1 stop bit.
61280.003L1-1B PAGE 9 TRACER DESCRIPTION AC/DC POWER The unit receives power via one of two connectors. Power for the entire system is provided by these interfaces. The three-pin circular DIN connector is provided to connect an optional ADTRAN desktop AC adapter (ADTRAN part number 1360.DSK24VL1), providing 24 volts DC. The three-pin terminal block allows the connection of any DC power source providing between 21 and 56 volts DC. The power consumption of the entire system is 30 watts.
PAGE 10 SECTION 1 61280.003L1-1B The LEDs associated with the DS1/DSX-1 interfaces are listed below. There are two sections of identical indicators -- one for each DS1/DSX-1 interface. BPV .............. Red if the incoming T1 stream contains bipolar violations RED ............. Red if there is no signal present at the T1 interface LPBK ............ Yellow if the T1 interface is in loopback YEL/AIS .......
61280.003L1-1B PAGE 11 TRACER DESCRIPTION The monitor points provided on the front panel of the system are listed below I ............................ Demodulated received baseband output Q .......................... Demodulated received baseband output CLK ..................... Recovered clock for observing EYE pattern RSSI ..................... DC voltage indicating strength of the received signal at the antenna +5 ......................... System 5 volts -5 ..........................
PAGE 12 SECTION 1 61280.003L1-1B This signal is used to align the antenna during installation and to verify that the link is performing as designed. A third test point is provided to monitor the transmitter output power during system configuration. The only connections that must be made in the field are a coax connection between the BBP and the RFC and a coax connection between the RFC and the antenna. The “IF” connector provides the connection between the BBP and the rack or mast-mounted RFC.
61280.003L1-1B PAGE 13 TRACER DESCRIPTION for mast-mounting near the antenna for enhanced system performance. The RFC mast-mount and rack-mount housings are illustrated below. Holes for Mounting Bracket Mounting Clearances Housing Assembly and Guide WARNING Figure 1-10. Mast-Mount RFC Housing TRACER TRA CER Figure 1-11. Rack-Mount RFC Housing ANTENNA Tracer is intended to be coupled with an antenna that is directional and provides signal gain.
PAGE 14 61280.
61280.003L1-1B PAGE 15 SECTION 2 INSTALLATION RADIO FREQUENCY INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for an intentional radiator, pursuant to Part 15, Subpart C of the FCC Rules. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause interference to radio communications.
PAGE 16 61280.003L1-1B SECTION 2 FCC OUTPUT POWER RESTRICTIONS The FCC does not require licensing to implement this device. However, the FCC has established restrictions regarding maximum output power and the adjustments required when employing directional gain antennae. (Refer to “Setting the Transmitter Power” in Section 2 of this manual). These restrictions are detailed in FCC Part 15.247 (b)(1), (b)(3)(i), and (3)(iii).
61280.003L1-1B PAGE 17 INSTALLATION UNPACK, INSPECT Carefully inspect the Tracer for any shipping damages. If damage is suspected, file a claim immediately with the carrier then contact ADTRAN Customer Service. If possible, keep the original shipping container for use in shipping the Tracer back for repair or for verification of damage during shipment. Before beginning installation, verify that all of the following components are present.
PAGE 18 61280.003L1-1B SECTION 2 INSTALLATION LOCATION Install the Tracer in a location that requires minimal antenna feedline length (the loss in this cable directly affects overall system performance). When the DS1/DSX-1 interface is configured for DS1 line buildouts, it can operate at lengths up to 6000 feet. POWER REQUIREMENTS The system power may be obtained from a DC power source if available, or an optional AC adapter available from ADTRAN.
61280.003L1-1B PAGE 19 INSTALLATION The supplementary equipment grounding conductor shall not be smaller in size than the undergrounded branch-circuit supply conductors. The supplementary equipment grounding conductor shall be connected to the product at the terminal provided, and shall be connected to ground in a manner that will retain the ground connection when the product is unplugged from the receptacle.
PAGE 20 61280.003L1-1B SECTION 2 interface circuitry is broken. The monitor jacks provide access to monitor the transmitted and received signals without interference. When connecting either T1 interface to the public switched network, an ADTRAN-provided crossover cable (part number 3125.M011@A) is required to meet FCC part 68 and IC CS03 requirements. This cable is required to cross-over the Tx and Rx pairs to meet the connecting arrangement of a network interface device.
61280.003L1-1B PAGE 21 INSTALLATION LINK PLANNING IMPORTANT The appropriate transmitter power must be calculated as part of the link planning. The factors that must be taken into account when planning a link are optimal received signal level, transmitter power, antenna feedline loss (each end), antenna gain (each end), free space path loss, and required fade margin. IMPORTANT The optimal signal level for the receiver is -60 dBm.
PAGE 22 61280.003L1-1B SECTION 2 ANTENNA GAIN Best performance will result from the use of a parabolic dish antenna. Antenna gain is determined by the size of the dish, with typical figures detailed below. Dish manufacturers will be able to supply gains for other types of antenna. Dish Diameter Gain (in feet) (in dBi) 2 ...................... 21 4 ...................... 27 6 ...................... 31 8 ...................... 33 10 ..................... 35 12 .....................
61280.003L1-1B PAGE 23 INSTALLATION PATH AVAILABILITY The availability of a path can be expressed by: availability = (1 - C x T x 2.5 x 10-6 x f x D3 x 10-F/10) x 100% where C is the climate factor T is the terrain factor f is the frequency in GHz D is the path length in miles F is the fade margin in dB Climate factors are given below. Climate Climate Factor Very Dry .............. 1/8 Temperate ............ 1/4 Humid .................
PAGE 24 61280.003L1-1B SECTION 2 SETTING THE TRANSMITTER POWER The FCC specifies the maximum transmitter power that may be used for antennae of a given gain. FCC rules Part 15, Subpart 247 allow for a maximum power of 1 watt into antennae of a gain less than or equal to 6 dBi. For every 3 dB of gain over 6 dBi, the transmitter must be reduced by 1 dB. The following table lists the maximum transmitter power for given antennae gains. Antenna Gain 6 dBi ......... 12 dBi ....... 18 dBi ....... 24 dBi .......
61280.003L1-1B PAGE 25 INSTALLATION To reconfigure the RFC interconnect, do the following: 1. Remove the four screws which retain the RFC cover and remove the cover. 2421 Anten na PLAN A 2462 2. The RF unit may be identified by following the connection from the port labelled “IF” on the rear of the RFC. This connection terminates at the RF unit. The diplexer may be identified by following the connection from the “Antenna” port on the rear of the RFC.
PAGE 26 61280.003L1-1B SECTION 2 9. Re-attach the cable assemblies from the ports labelled “Tx” and “Rx” on the RFC, and the ports labelled “2422” and “2462” on the diplexer. Cable connections should be aligned to each other as follows. Plan A Tx = 2422 Rx = 2462 Plan B Tx = 2462 Rx = 2422 10. Replace and secure the RFC cover. CONNECTING THE BBP AND THE RFC The BBP and the RFC are connected by an IF cable, either supplied by ADTRAN (for rack-mount assembly) or by the customer (for mast-mount assembly).
61280.003L1-1B PAGE 27 INSTALLATION SETTING THE BBP FREQUENCY PLAN Upon the initial application of power, the BBP will default to the factory-preset Frequency Plan, or to the Frequency Plan in use when the unit was last powered-down. The BBP attached to the RFC configured for Plan B must be set to Plan B by pressing the “Plan” switch on the front panel. The LED will indicate which frequency plan is active.
PAGE 28 61280.003L1-1B SECTION 2 3. If the systems are from different manufacturers, set the transmit frequencies as close as possible with different spreading codes. Other manufacturers may not use the exact frequency plans as the Tracer system, but keeping the frequencies close will reduce the probability of the transmitter(s) interfering with the colocated receiver(s). This equipment is authorized under CFR 47 Part 15.247.
61280.003L1-1B PAGE 29 INSTALLATION than the other. Changing the spreading code at each end may also allow interference to be mitigated. REMOTE BERT The Tracer includes a Bit Error Rate Tester (BERT) to verify that the installed system is operating correctly. When the “Remote Test” button is pushed on the local BBP, the remote end will send a BERT pattern for approximately ten seconds. The “Remote TST” indicator will turn yellow and remain on for the duration of the test.
PAGE 30 61280.
61280.003L1-1B PAGE 31 SECTION 3 OPERATION VT-100 USER INTERFACE The Tracer may be accessed with a VT-100 compatible terminal set to 9600 bits per second, 8 data bits, and no parity, connected to the RS-232 port on the back of the unit. Once a terminal is connected, pressing the ESC key will present the System Status screen. If password access has been enabled, then press “Enter” or “Return” in order to see the “Enter Password:” message. Tracer is shipped with password protection disabled.
PAGE 32 61280.003L1-1B SECTION 3 PASSWORD Tracer provides optional password protection of the terminal interface. If enabled, a password prompt is presented at powerup, reboot, or after thirty minutes of inactivity on the terminal. The default configuration is “No password.” Password protection is enabled via the configuration menu. The password is also set via the configuration menu. If the password is forgotten, physical access to Tracer is required to access the terminal interface.
61280.003L1-1B PAGE 33 OPERATION MAIN MENU SELECTIONS SYSTEM STATUS PAGE This page displays the status of major system components. This is a status screen only; no configurations can be performed. More detailed information can be obtained by way of the Main Menu.
PAGE 34 61280.003L1-1B SECTION 3 MAIN MENU PAGE Pressing “M” on any screen will take the user to the Main Menu, from which the subsequent screens can be accessed. TRACER Main Menu, Rev: A Site: Adtran 1) 2) 3) 4) 5) 6) 7) T1 Status Page T1A Performance History T1B Performance History Alarm Page Test Menu Configuration Menu Remote Access ===================================================================== Press ESC for System Status: Figure 3-2.
61280.003L1-1B PAGE 35 OPERATION CHANNEL A STATISTICS PAGE This screen presents detailed error statistics for T1A. The data is presented as Errored Seconds and Severely Errored Seconds. The counts for the most recent 24 hours are recorded in 15-minute increments. Twenty-four-hour totals are recorded for the most recent days.
PAGE 36 61280.003L1-1B SECTION 3 ALARM PAGE This screen presents alarm information for the system. The T1A or T1B alarms are described in the chapter entitled “Troubleshooting.” If any of the T1A or T1B alarms are active, a minor alarm will be indicated at the alarm contacts. The RF link alarm will be activated when communication between the BBP and the RFC has failed. Code Sync, Carrier Sync, and T1 Mux Framer alarms indicate that various portions of the spread spectrum data pump are not operating.
61280.003L1-1B PAGE 37 OPERATION Each menu selection is described below: 1. Loops the local T1-A Interface towards the local equipment. 2. Loops the local T1-B Interface towards the local equipment. 3. Loops the local T1-A interface towards the remote equipment, over the RF Link. 4. Loops the local T1-B interface towards the remote equipment, over the RF Link. 5. Loops the remote T1-A Interface towards the local equipment, over the RF Link. 6.
PAGE 38 61280.003L1-1B SECTION 3 The menu selections are described below. T1A and T1B Framing allow each T1 to be configured for SF or ESF framing. T1A and T1B Line Code allow each T1 to be configured for AMI or B8ZS. T1A and T1B Line Buildout allow each T1 to be configured for the appropriate line buildout, based on the distance to the T1 equipment. WARNING It is possible for the spreading code to be changed remotely through the VT-100 interface from the other end of the link.
61280.003L1-1B PAGE 39 SECTION 4 TROUBLESHOOTING GENERAL If you experience a problem with the Tracer system, check to ensure that all connectors, coaxial cables, antennae and T1s are all properly connected; and that the system configuration ensures proper transmit and receive levels for the RF equipment. Then, if the problem persists, follow the actions recommended in this section. For further assistance, call ADTRAN Technical Support at (800)␣ 726-8663.
PAGE 40 61280.003L1-1B SECTION 4 PROBLEM DESCRIPTIONS AND RECOMMENDED ACTIONS Each problem described below is followed by a list of Possible Causes, each of which is followed by a number (or numbers) corresponding to a Recommended Action (or Actions). IMPORTANT If problems persist after you have followed the Recommended Actions, contact ADTRAN Technical Support at (800) 726-8663.
61280.003L1-1B PAGE 41 TROUBLESHOOTING IMPORTANT If problems persist after you have followed the Recommended Actions, contact ADTRAN Technical Support at (800) 726-8663. 7. 8. 9. 10. Check all connections between the BBP, the RFC, and the antenna. Check the IF and RF cables for shorts. Check the connections inside the mast-mount or rack-mount RFC. Replace the RFC. “BPV” LIGHT ON T1-A OR B IS LIT This alarm will activate when the incoming T1 stream presents BPVs.
PAGE 42 61280.003L1-1B SECTION 4 IMPORTANT If problems persist after you have followed the Recommended Actions, contact ADTRAN Technical Support at (800) 726-8663. “LBK-A” OR “LBK-B” IS LIT This alarm will activate when a software or manual T1 loopback has been established. POSSIBLE CAUSE RECOMMENDED ACTION (SEE LIST BELOW) • A loopback has been commanded from the VT-100 user interface. ....................................................................
61280.003L1-1B PAGE 43 TROUBLESHOOTING IMPORTANT If problems persist after you have followed the Recommended Actions, contact ADTRAN Technical Support at (800) 726-8663. “AIS/YEL” INDICATOR IS FLASHING This alarm is activated when the T1 interface at the remote end is not receiving a T1 signal (it is in Red alarm). In this circumstance the interface with the flashing AIS/YEL indicator is transmitting an AIS (keep alive) signal.
PAGE 44 61280.003L1-1B SECTION 4 IMPORTANT If problems persist after you have followed the Recommended Actions, contact ADTRAN Technical Support at (800) 726-8663. “TEST” LIGHT IS LIT OR BLINKING The test alarm will remain on (solid) during power-up, indicating a self-test is in progress. The light will flash or remain on (solid) if the self-test fails. POSSIBLE CAUSE RECOMMENDED ACTION (SEE LIST BELOW) • One-flash interval indicates a RAM test failure. ...............................
61280.003L1-1B PAGE 45 TROUBLESHOOTING IMPORTANT If problems persist after you have followed the Recommended Actions, contact ADTRAN Technical Support at (800) 726-8663. “FAIL” LIGHT IS LIT AFTER PRESSING “REMOTE TEST” BUTTON The Remote Fail light will activate after a Remote Test has failed. POSSIBLE CAUSE RECOMMENDED ACTION (SEE LIST BELOW) • The 10-second BERT has failed over the RF link to the far-end. .........................................................................................
PAGE 46 61280.003L1-1B SECTION 4 IMPORTANT If problems persist after you have followed the Recommended Actions, contact ADTRAN Technical Support at (800) 726-8663. TROUBLESHOOTING USING THE VT-100 USER INTERFACE This section provides information for troubleshooting the Alarm Menu on the VT-100 user interface. The conditions present in the Alarm Menu are software indications and should match the front panel LED indications.
61280.003L1-1B PAGE 47 TROUBLESHOOTING IMPORTANT If problems persist after you have followed the Recommended Actions, contact ADTRAN Technical Support at (800) 726-8663. RECOMMENDED ACTIONS: 1. 2. Check the incoming DS1/DSX-1 signal for BPVs using a T1 test set. Correct the line code on the Tracer or DS1/DSX-1 equipment. YEL/AIS ALARM This alarm indicator will flash when a T1 Yellow alarm occurs.
PAGE 48 61280.003L1-1B SECTION 4 IMPORTANT If problems persist after you have followed the Recommended Actions, contact ADTRAN Technical Support at (800) 726-8663. RF LINK ALARM OR CODE SYNC ALARM The RF Link Alarm will activate when the link is down or not operational. The Code Sync Alarm will activate when data synchronization has not been achieved between the RF link. POSSIBLE CAUSE RECOMMENDED ACTION (SEE LIST BELOW) • The RF link is down. ...........................................................
61280.003L1-1B PAGE 49 TROUBLESHOOTING IMPORTANT If problems persist after you have followed the Recommended Actions, contact ADTRAN Technical Support at (800) 726-8663. CARRIER SYNC ALARM OR T1 MUX FRAMER ALARM The Carrier Sync alarm will activate when frequency synchronization has not been achieved between the RF link. The T1 Mux Framer alarm will activate when synchronization between the T1 mux on each radio has not been achieved.
PAGE 50 61280.003L1-1B SECTION 4 IMPORTANT If problems persist after you have followed the Recommended Actions, contact ADTRAN Technical Support at (800) 726-8663. ES VALUES IN T1 STATUS MENU This value indicates the number of Errored Seconds in the T1 data stream. POSSIBLE CAUSE RECOMMENDED ACTION (SEE LIST BELOW) • In an AMI-coded T1, a BPV or frame bit error has occurred. ............................................................................................
280.003L1-1B PAGE 51 SECTION 5 SPECIFICATIONS This section lists the specifications for the Tracer system. TRANSMITTER Output Power ............................. +20 dBm, maximum Frequency Range ........................ 2400 to 2483.5 MHz Channel Bandwidth ................... 40 MHz (two channels) I/F ............................................... 140 MHz RECEIVER Receive Level, range ................... -30 to -91 dBm (10-6 BER) Receive Level, maximum ........... -30 dBm Receive Level, nominal ...
PAGE 52 61280.003L1-1B SECTION 5 INTERFACE SPECIFICATIONS Capacity ...................................... 2 x T1 Connection ................................. RJ-48C, bantam Line Code ................................... AMI, B8ZS Framing ...................................... SF, ESF Alarms ........................................ AIS, Red, Yellow, BPVs Loopbacks .................................. Local and remote, per T1 channel USER INTERFACE Front Panel .................................
61280.003L1-1B PAGE 53 SPECIFICATIONS Mast Unit Operating Temperature .............. -40°C to 65°C Size ............................................. 21" high x 9" diameter Humidity .................................... 100% Weight ........................................ 18 lbs. POWER Input Voltage .............................. 21 to 56 volts DC, either polarity referenced to ground Power Consumption .................. 30 watts Connector ...................................
PAGE 54 61280.
61280.003L1-1B SECTION 6 PAGE 55 WARRANTY, ORDERING AND RETURN INFORMATION WARRANTY Adtran will replace or repair this product within five years from the date of shipment if it does not meet its published specifications or fails due to defects in materials and workmanship. For detailed warranty, repair, and return information, refer to the Adtran Equipment Warranty, Repair, and Return Policy and Procedure.
PAGE 56 61280.003L1-1B SECTION 6 TECHNICAL SUPPORT Standard support hours are 7 a.m. to 7 p.m. CST, Monday through Friday. Emergency technical support is available 24 hours a day, seven days a week.
61280.003L1-1B PAGE 57 GLOSSARY ACRONYMS USED IN THIS MANUAL AMI .............. B8ZS ............. BER .............. BBP .............. CRC ............. DCE ............. DTE ............. ESF .............. FCC ............. FEC .............. IF ................. ISM .............. LBK .............. QPSK ........... RF ................ RFC .............. RSSI ............. Rx ................ SF ................. Tx ................
PAGE 58 61280.
61280.003L1-1B PAGE A - 1 CABLE CONNECTIONS APPENDIX A CABLE CONNECTIONS The cable connections required for various configurations are detailed below. TERMINAL CONNECTION (DB25) Tracer (DCE) Number Name 2 ............... TXD 3 ............... RXD 4 ................ RTS 5 ................ CTS 6 ................ DSR 7 ............. Ground Terminal (DTE) Number Name 2 ............... TXD 3 ............... RXD 4 ............... RTS 5 ............... CTS 6 ............... DSR 7 ............
PAGE A - 2 61280.003L1-1B APPENDIX A MODEM CONNECTION (DB25) Tracer (DCE) Number Name Modem (DCE) Number Name 2 ............... TXD 3 ............... RXD 3 ............... RXD 4 ................ RTS 5 ................ CTS 6 ................ DSR 7 ............. Ground 2 ............... TXD 5 ............... CTS 4 ............... RTS 20 .............. DTR 7 ............
61280.003L1-1B PAGE B - 1 FCC REGULATIONS APPENDIX B FCC REGULATIONS 1. This equipment complies with Part 68 of the FCC Rules. On the bottom of this equipment is a label that contains, among other information, the FCC Registration number for this equipment. If requested, provide this information to your telephone company. 2. Below is a list of all applicable registration jack USOCs (Facility Interface Codes and Service Order Codes) for the equipment.
PAGE B - 2 61280.003L1-1B APPENDIX B 8. This equipment may not be used on public coin service provided by the telephone company. Connection to party lines is subject to state tariffs. (Contact your state public utility commission or corporation commission for information.) 9. Connection of Private Communication Systems: Private communication systems (microwave, etc.) may be directly connected to the network through the use of VP couplers; or to station ports behind registered host systems.
61280.003L1-1B PAGE B - 3 FCC REGULATIONS AFFIDAVIT FOR CONNECTION OF CUSTOMER PREMISES EQUIPMENT TO 1.
PAGE B - 4 61280.003L1-1B APPENDIX B I attest that the operator(s)/maintainer(s) of the digital CPE responsible for the establishment, maintenance, and adjustment of the encoded analog content and billing information has (have) been trained to perform these functions by successfully having completed one of the following (check appropriate blocks): [ ] A. A training course provided by the manufacturer/grantee of the equipment used to encode analog signals; or [ ] B.