C AMBRIDGE C IG In d u s t r ies (Gr o up) C o L t d . ONT TA334RG Hardware Installation Manual Aug. 2012 Rev. 2 Cambridge Industries Group Co.
ONT TA334RG Hardware Installation Manual Table of Contents About This Document _________________________________________________________ IV Purpose ___________________________________________________________________________ IV Intended Audience _________________________________________________________________ IV Chapter Overview __________________________________________________________________ IV 1. Product Description _________________________________________________________ 1 1.
ONT TA334RG Hardware Installation Manual 4.1 ONT Status LEDs ____________________________________________________________ 15 4.2 Troubleshooting Procedures ____________________________________________________ 19 Rev. 1: Oct. 2011 Cambridge Industries Group Co.
ONT TA334RG Hardware Installation Manual About This Document Purpose This guide describes how to install the ADTRAN optical network termination unit (ONT) at the customer premises.
ONT TA334RG Hardware Installation Manual 1. Product Description 1.1 Introduction Optical Network Terminal (ONT) model TA334RG is an ITU-T G.984 compliant device that receives voice, data, and video traffic in the form of optical signal from the service provider’s passive optical network (PON) and transmitted it to the desired format at residential or business premises. Upstream traffic is likewise transmitted to the PON network via the fiber optic cable.
ONT TA334RG Hardware Installation Manual ONT physical, electrical, optical, and environmental specifications and compliance information are listed in the following tables. Dimensions 229mm (width) by 174mm (depth) by 41mm (height)(without bracket) 229mm (width) by 174mm (depth) by 49mm (height)(with bracket) Weight 0.
ONT TA334RG Hardware Installation Manual PON ITU-T G.984.1, G.984.2, G.984.2 amd1, G.984.3, G.984.4, G.983.2 EMC ETSI EN 300386, EN 55022 (Class B) Safety EN 60950 Laser ITU-T Rec.G.984.2 (Class B+), G983.3 FCC 47 CFR Part 15, Class B FDA 21 CFR 1040.10 and 1040.11, Class I IEC 60825, Class I Table 4 Compliance Minimum Nominal Maximum Wavelength 1260 nm 1310 nm 1360 nm Transmit power 0.
ONT TA334RG Hardware Installation Manual 2. Safety This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
ONT TA334RG Hardware Installation Manual Install the device in compliance with the requirements. Do not open the device enclosures without permission, but contact the service technician when a problem occurs with the device. No entity or person should modify the structure, security design, performance design, etc. of the device without authorization. Abide by local laws and regulations and respect the legal rights of others when using the device. 2.
ONT TA334RG Hardware Installation Manual 2.4 Laser Safety Persons handling fiber optic cables must be trained for laser safety. Do not bend the fiber optic cable to a diameter smaller than 7.5 cm/3 inches, so as not to damage the fiber or prevent the signal from passing through properly. Do not look directly into the optical port on the device without eye protection. The laser emitted from the optical port can cause injury to your eyes. 2.
ONT TA334RG Hardware Installation Manual 3. Installation 3.1 Site Preparation 3.1.1 Environmental Requirements The ONT will operate in temperatures ranging from 0° C to 40° C, relatively humidity ranging from 5% to 95%. 3.1.2 Power Requirements The ONT will be shipped with a universal power adaptor. However, before installation, check if the AC power input matches the specification printed on the power adaptor (input voltage, current, etc.
ONT TA334RG Hardware Installation Manual Figure 1 ONT Elements 3.3 Mountings & Connecting to Network 3.3.1 Installing the ONT on Wall 1. Locate a safe and accessible site for installation. 2. Align the ONT mounting bracket on the wall. There are two mounting directions, either horizontal (Figure ) or vertical (Figure ). Make sure the install arrows is up when correctly mounted.
ONT TA334RG Hardware Installation Manual Figure 4 Bracket mounting: Vertical direction 3. Mount the bracket into a wall stud by driving the two sheet metal screws into the wall through the bracket mounting holes (Figure ). Notice ADTRAN have the sole right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice, ADTRAN has the final interpretation.
ONT TA334RG Hardware Installation Manual Figure 5 Mount the bracket into the wall 4. Wrap the fiber optical cable on the fiber storage tray. Make sure the SC/APC connector comes out from the bottom left side in case of horizontal mounting, or left up side in case of vertical mounting. Secure the fiber with the cable holder. 5. Slide the ONT unit into the mounting bracket in up to down direction, using the 4 guides on the bracket.
ONT TA334RG Hardware Installation Manual 3. If necessary, remove the optical fiber cables. 4. If necessary, remove the bracket mounting screws and then remove the mounting bracket. For uninstall the ONT on the desktop: 1. Plug out the SC/APC optical connector. 2. If necessary, remove the optical fiber cables. 3.4 Connecting Power 1. Plug the circle two pin 12V DC power connector of power converter to ONT power port 2. Plug the input of power converter into a live AC outlet 3.
ONT TA334RG Hardware Installation Manual Pin Color Signal Pin Color Signal 1 Orange/White TX_D1+ 5 Blue/White BI_D3- 2 Orange TX_D1- 6 Green RX_D2- 3 Green/White RX_D2+ 7 Brown/White BI_D4+ 4 Blue BI_D3+ 8 Brown BI_D4- Table 7 Ethernet RJ-45 connector wiring pattern 3.7 Connecting Analog Video Service 1. Locate the premises’ coax video cable. 2. If the cable is not terminated, follow local practices to attach a 75 Ohm type F coaxial connector. 3.
ONT TA334RG Hardware Installation Manual 3.8 Verifying the Installation Check LED states to verify ONT status (Section 3.8.1). Services are not available until the ONT is ranged and provisioned in the PON network. If services must be verified at the time of installation, refer to Section 3.8.2 for additional instructions. 3.8.1 Activating the ONT Once the ONT installation is complete, follow the procedure below for verifying ONT status.
ONT TA334RG Hardware Installation Manual 3.8.2 Verifying Services Follow local practices to connect to each active service port in the ONT to confirm service activation. 1. If VID service is included in this installation, verify the VID LED is green. 2. Connect to each active phone jack to verify telephone numbers and services. Verify that the TEL LED lights green when a line is off hook. 3.
ONT TA334RG Hardware Installation Manual 4. Troubleshooting 4.1 ONT Status LEDs The ONT status LEDs located on the enclosure (Figure 4) assist with installation and maintenance procedures. These LEDs are described in detail in Table .
ONT TA334RG Hardware Installation Manual LED Color Indicates Green/Solid Normal.
ONT TA334RG Hardware Installation Manual LED Color Indicates Green/Solid ONT register to SS and on hook Green/Flash Off hook(on register) or Call in OFF No register Name TEL2 Green/Solid Indicate PPPoE / DHCP signup completed successfully.
ONT TA334RG Hardware Installation Manual Notice ADTRAN have the sole right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice, ADTRAN has the final interpretation.
ONT TA334RG Hardware Installation Manual 4.2 Troubleshooting Procedures Problem Possible Solutions Check whether the ON/OFF button on the rear „ panel is pressed. The POWER LED is off Check whether the power adapter matches the TA334RG. Check whether the power connection is correct. Check whether the optical fiber is connected correctly. The LINK LED is off Check whether there is dirt on the optical connector. The TA334RG may not receive the downstream The LINK LED is on, but the INTERNET LED is off.
ONT TA334RG Hardware Installation Manual The WPS LED is off Check whether the WPS service is started. The WLAN LED is off Check whether the WLAN service is started. The USB LED is off Check whether the cable is normal. Video power level is low, or video service is The VID LED is off disabled. Contact NOC for verification.