FCC ID:P27SCE2R0 SCE2R0-29 Outdoor Camera Setup Guide Document Version: 1.
FCC ID:P27SCE2R0 Table of Contents Chapter 1 Introduction .......................................................................................................... 1 Package Contents .............................................................................................................. 1 Chapter 2 Setup ...................................................................................................................... 2 System Requirements .........................................................
FCC ID:P27SCE2R0 Chapter 1 Introduction 1 Package Contents The following items should be included: If any of these items are damaged or missing, please contact your dealer immediately. 1. SCE2R0-29 Battery Camera x 1 2. Battery Pack x 1 3. Mounting Stand x 1 4.
FCC ID:P27SCE2R0 Chapter 2 Setup This Chapter provides details on how to install and configure the Battery Camera. 2 System Requirements A computer or mobile device with Internet access You can use the following web browser while using a computer: • Internet Explorer 7 or later • Firefox 3 • Safari 4 • Chrome Physical Details – Smart Video Camera LED Color Status The camera is registered and connected to the network. Solid Green Solid Green (5 seconds) WPS pairing is failed.
FCC ID:P27SCE2R0 Front Panel Microphone The built-in microphone is useful for bi-direction voice conversation. Light Sensor This is hardware sensor to detect LUX. Lens No physical adjustment is required or possible for the lens, but you should ensure that the lens cover remains clean. The image quality is degraded if the lens cover is dirty or smudged. IR LEDs They are used to provide illumination for night time. PIR Sensor This is hardware sensor for detecting motion.
FCC ID:P27SCE2R0 Side Panel Reset/WPS This button has two functions: WPS: -WPS PBC Mode: When pressed and released (less then 3 seconds), the Camera will be in the WPS PBC mode (Auto link mode). -WPS Pin Code Mode: When pressed and held for over 3 seconds, the Camera will be in the WPS Pin Code mode. Reset: When pressed and held over 10 seconds, the LED will be flashing red, which means the settings of Camera will be set to their default values. SD Card Slot Insert the SD card for external storage.
FCC ID:P27SCE2R0 Pre-Installation Insert the Battery Pack Align the battery contacts and then insert the battery pack into the camera. Note: Be sure to charge the battery when use it for the first time.
FCC ID:P27SCE2R0 Battery Pack Charging You can charge your camera battery indoors using the Micro USB cable. Note: For safety reasons, the battery charging temperatures are from 5°C to 35°C. 1. Put the battery pack into the camera. 2. Connect the power Micro USB cable to the USB port of the camera. 3. Plug the other end of power Micro USB cable into power adaptor for charging. Battery Pack LED Color Status Solid Green The charging is complete. Solid Red The battery pack is charging.
FCC ID:P27SCE2R0 Installation 1. 2. Move the camera to where it is to be placed. Check the LED: The LED light bar should be solid blue when the camera is powering on. Mounting Installation Place the camera in a flat surface or mount it on the wall/ceiling. Check the network signal strength in the place where you want to locate the camera. Avoid placing the camera in an area that gets a lot of light directly into the camera lens. Wall Mounting 1. Identify the location for mounting the Camera. 2.
FCC ID:P27SCE2R0 Chapter 3 Viewing Live Video 3 This Chapter provides basic information about viewing live video. Overview This Chapter has details of viewing live video using Internet Explorer. Requirements To view the live video stream generated by Battery Camera, you need to meet the following requirements: Windows XP, 32-bit Windows Vista/Windows 7. Internet Explorer 7 or later, Firefox 3.0 or later.
FCC ID:P27SCE2R0 7. The first time you connect to the camera, you will be prompted to install decoders. Choose "I accept the terms of the license agreement" and click "OK". 8. Video will start playing automatically. There may be a delay of a few seconds while the video stream is buffered.
FCC ID:P27SCE2R0 Appendix A Specifications SCE2R0-29 Battery Camera Model SCE2R0-29 Dimensions (H x W x D) 72mm x 93mm x 71.35mm Operating Temperature -10 C to 50 C Charging Temperature 5 C to 35 C Storage Temperature -20 C to 50 C Network Protocols TCP/IP, HTTP, HTTPS, DHCP, NTP, RTP, RTCP, RTSP, DNS Network Interface IEEE 802.
FCC ID:P27SCE2R0 Regulatory Approvals FCC Statement This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.