ADOMAX TECHNOLOGY CO.,LTD Requirements Specification For AM-2200UP OPTICAL 27MHz Wireless 3D Mouse Date: 91.11.11 Revision: 1.
Contents 1.0 SCOPE............................................................................................................................................................. 1 1.1 DOCUMENT ................................................................................................................................................... 1 1.2 PRODUCT FEATURES ..................................................................................................................................... 1 1.
Wireless 3D Mouse Requirements Specification 1.0 Scope 1.1 Document This document summarizes the requirements for the Wireless 3D Mouse (WLM). 1.2 Product Features • • • Wireless mouse eliminates cable between mouse and the PC 800 cpi 3D mouse 1.3 Product Applications • • • • Laptop PC Desktop PC Operate OS: window 98/2000/ME/XP/MAC OS Includes software driver for window 98/2000/ME/XP/MAC OS 2.0 Items 2.1 Applicable Documents N/A 2.
3.0 Requirements 3.1 General Description The WLM consists of the mouse unit and the base unit. The battery powered mouse unit transmits an RF signal to the base unit that is connected to the USB (PS/2) port on the PC or laptop computer. 3.1.1 Characteristics The following sections identify the detailed specifications of the WLM. 3.1.1.1 Functional Block Diagram The typical operational configuration for WLM is shown in Figure 1 below. M ouse Unit RF Laptop -orDesktop Base Unit Figure 1.
Figure 3. Receiver Block Diagram 3.1.1.2 Performance Requirements 3.1.1.2.1 Product Performance Requirements The end-to-end system performance requirements are contained in the Table 1 below. Table 1. System Performance Requirements Rqmt No. 3.1.1.2.1.1 3.1.1.2.1.2 Parameter RF channel RF channel Description Operating frequency bands Number of channels Value 27 MHz 1 channels 3.1.1.2.
3.1.1.2.3 Base Unit Performance Requirements The base unit performance requirements are contained in the Table 3 below. Table 3. Receiver Performance Requirements Rqmt No. 3.1.1.2.3.1 3.1.1.2.3.2 Parameter RF frequency Receiver antenna Description Receive carrier frequencies Antenna type 3.1.1.2.3.
3.1.3 Physical Characteristics 3.1.3.1 Mouse Unit Physical Characteristics The board design parameters are shown in Table 6. Table 6. Mouse Unit Physical Characteristics Rqmt No. 3.1.3.1.1 3.1.3.1.2 Parameter Outline dimensions Length Width Height Battery Description Value Maximum length Maximum width Maximum height Provide room for battery compartment 125mm 68mm 30mm AA x 2 (two pieces) Type 3 Alkaline battery 3.1.3.
P a r B C U C a a s U t t e p a a g R M a O m U S l e S H D P E o a e o r t a a n n s d m b y T S S r a t a l e n n e s d p m b y T o a l B u h h l m a u M b a n s t r e m A A p e t t e r y f w o f m t e r i e c k t o w a k e - u p s N A 2 8 0 0 2 0 .
3.1.6 Reliability Reliability testing of the mouse unit shall be performed under the following conditions. Table 9. Reliability Test Rqmt No. 3.1.6.1 Parameter Mouse life test Description Load Speed Travel Base Unit Value Not applicable 3.1.6.2 Switch life test Not applicable 3.1.6.
3.1.6.11 Color box packaged unit shock test 3.1.6.12 Color box packaged unit vibration test Total cycles Height Floor condition Frequency Force Dwell time Direction Cycles 6 faces 2 edges 1 corner 65 cm Plastic floor tile 5 to 50 Hz 3.0 g 6 minutes each axis 3 axis vibration 10 cycles 3.1.7 Manufacturing Requirement The objective is to drive the manufacturing cost down through fewer parts, higher volume, lower SMT cost, higher yield and lower manufacturing overhead. 3.1.7.
Parameter Click to wake-up Battery type Capacity (mAh) Usage percentage of batteries CURRENT USAGE Transmit (mA) Standby (mA) Notes AAA Type 3 battery 1200 Alkaline (duracell web page) 80% Operation voltage> 2.2V 28 RF and Digital 0.7 Digital only RF and Digital power down 0.02 Microprocessor sleep Sleep (mA) MOUSE USAGE Hours per day Days per week Percent usage 4 5 15% Total Mouse usage per week (hours) 3.
Information to User Notice 1 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. Notice 2 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
