67& Smart Touch Computer User’s Manual Manual Rev.: 0.30 Revision Date: October 5, 2015 Part No: 50-1Z203-2000 Advance Technologies; Automate the World.
Revision History Revision Release Date 0.10 17/07/2015 Preliminary release 0.20 11/08/2015 Update COM1/2 specification; add OS support; panel mount thickness support; power switch description 0.
STC-1 05 Preface Copyright 2015 ADLINK Technology Inc. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.
Conventions Take note of the following conventions used throughout this manual to make sure that users perform certain tasks and instructions properly. Additional information, aids, and tips that help users perform tasks. NOTE: CAUTION: WARNING: iv Information to prevent minor physical injury, component damage, data loss, and/or program corruption when trying to complete a task.
STC-1005/ 1205/ 1505 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This page intentionally left blank.
STC-1005/ 1205/ 1505 Table of Contents Revision History...................................................................... ii Preface .................................................................................... iii List of Figures ........................................................................ ix List of Tables.......................................................................... xi 1 Introduction ........................................................................ 1 1.
This page intentionally left blank.
STC-1005/ 1205/ 1505 List of Figures Figure 1-1: Figure 1-2: Figure 1-3: Figure 2-1: Figure 3-1: Figure 3-2: Figure 3-3: Figure 3-4: Figure 3-5: Figure 3-6: Figure 3-7: Figure 3-8: STC-1005 Dimensions..................................................... 3 STC-1205 Dimensions..................................................... 4 STC-1505 Dimensions..................................................... 5 STC-1005/1205/1505 Rear I/O Layout ............................ 9 Panel Mount Installation .............
This page intentionally left blank.
STC-1005/ 1205/ 1505 List of Tables Table 2-1: Table 2-2: Table 2-3: Table 2-4: Table 2-5: Table 2-6: Table 2-7: List of Tables USB 3.0 Port Pinout....................................................... 10 USB 2.0 Port Pinout....................................................... 10 HDMI Port Pinout........................................................... 11 COM1/2 Port Pinouts..................................................... 11 RJ-45 GbE Pin Definitions ............................................
This page intentionally left blank.
STC-1005/ 1205/ 1505 1 Introduction 1.1 Overview The STC-1005/1205/1505 series of Smart Touch Computers is designed for industrial automation and other applications in harsh environments requiring an IP65 compliant front bezel with projected capacitive multi-touch display. Typical applications include industrial control systems for the food and beverage industries; automated buildings; transportation; hospitals; factories; and leisure facilities. 1.2 Features X 10.4”/12.
1.3 Package Contents Please check that your package contains the items below. If you discover damaged or missing items, please contact your vendor. X STC-1005/1205/1505 Smart Touch Computer X 19 VDC power adapter (input: 100-240 VAC, 1.5A, 50-60Hz) X Panel mount bracket kit X SATA drive mounting screws WARNING: 2 DO NOT install or apply power to equipment that is damaged or if there is missing/incomplete equipment. Retain the shipping carton and packing materials for inspection.
STC-1005/ 1205/ 1505 1.
Dimensions in mm Figure 1-2: STC-1205 Dimensions 4 I ntroduction
STC-1005/ 1205/ 1505 Dimensions in mm Figure 1-3: STC-1505 Dimensions I ntroduction 5
This page intentionally left blank.
STC-1005/ 1205/ 1505 2 System Description 2.1 Specifications Display Display Size Resolution Brightness Contrast Ratio Touchscreen 10.4" 12.1" 1024x 768 pixels 500 nits (w/o touch) 1000:1 15" 400 nits (w/o touch) 700:1 5-wire resistive touch sensor / projective capacitive sensor (optional) System Components Processor Memory Storage I/O Wireless Connectivity Operating System Intel® Atom™ Processor E3845, quad core, 1.91GHz 2GB DDR3L soldered onboard 1x SATA Slim slot 1x SATA Slim slot or 2.
Environmental & Certifications Operating Temperature Storage Temperature Relative Humidity Vibration Operating Shock Operating Ingress Rating Certifications & Compliance 8 -20°C to 60°C -20°C to 60°C 10% to 90 % @ 40°C (non-condensing) 1G random 5 to 500Hz 10G acceleration part to part, 11ms IP65 rated front panel CE, FCC, CB (IEC 60950-1) System Description
STC-1005/ 1205/ 1505 2.
2.3 Pin Definitions USB 3.0 Connectors Pin # Signal Name 1 VCC 2 Data- 3 Data+ 4 GND 5 RX_N 6 RX_P 7 GND 8 TX_N 9 TX_P Table 2-1: USB 3.0 Port Pinout USB 2.0 Connector Pin # Signal Name 1 Vcc 2 Data- 3 Data+ 4 GND Table 2-2: USB 2.
STC-1005/ 1205/ 1505 HDMI Connector Pin # Signal Pin # Signal 1 3 TMDS Data2+ 2 TMDS Data2 Shield TMDS Data2– 4 TMDS Data1+ 5 TMDS Data1 Shield 6 TMDS Data1– 7 TMDS Data0+ 8 TMDS Data0 Shield 9 TMDS Data0– 10 TMDS Clock+ 11 TMDS Clock Shield 12 TMDS Clock– 13 CEC 14 Reserved 15 SCL 16 SDA 17 DDC/CEC Ground 18 +5 V Power 19 Hot Plug Detect Table 2-3: HDMI Port Pinout COM1/2 Ports (RS-232 TX/RX only) Pin 1 Pin 5 Pin 6 Pin 9 Pin No RS-232 Pin1 - Pin2 RX Pin3
RJ-45 Gigabit Ethernet Connectors Pin # 10BASET/100BASE-TX 1000BASE-T 1 TX+ MDI0+ 2 TX- MDI0- 3 RX+ MDI1+ 4 — MDI2+ 5 — MDI2- 6 RX- MDI1- 7 — MDI3+ 8 — MDI3- Table 2-5: RJ-45 GbE Pin Definitions Speed 8 Activity 1 Status Speed LED (Green/Orange) Activity LED (Yellow) Network link is not established or system powered off OFF OFF OFF ON Active OFF Blinking Link Green ON Active Green Blinking Link Orange ON Active Orange Blinking Link 10 Mbps 100 Mbps 1000
STC-1005/ 1205/ 1505 DC Power Input Connector Table 2-7: DC Power Input Pinout System Description 13
This page intentionally left blank.
STC-1005/ 1205/ 1505 3 Getting Started 3.1 Panel Mounting The STC-1005/1205/1505 can be panel mounted using the 8 brackets included with the device. Make sure there is adequate space behind the panel for ventilation, and that the panel material and thickness can support the weight of the device. The mounting brackets can accommodate a maximum panel thickness of 2 mm. NOTE: 1. Cut the panel opening using the appropriate cutout dimensions shown below. 2.
Panel Mount Bracket M4 Screw M4 Screw Panel Mount Bracket Figure 3-1: Panel Mount Installation 16 Getting Started
STC-1005/ 1205/ 1505 Panel Mount Cutout Dimensions Dimensions in mm Figure 3-2: STC-1005 Panel Mount Cutout Dimensions Getting Started 17
Dimensions in mm Figure 3-3: STC-1205 Panel Mount Cutout Dimensions 18 Getting Started
STC-1005/ 1205/ 1505 Dimensions in mm Figure 3-4: STC-1505 Panel Mount Cutout Dimensions Getting Started 19
3.2 SD Card Installation To install or remove the SD card, loosen the screw securing the SD card slot cover. Insert or remove the SD card as required. Figure 3-5: SD Card Installation (STC-1005 shown) Replace the slot cover and tighten the scew.
STC-1005/ 1205/ 1505 3.3 STC-1005 SATA Slim Drive Installation To install or replace a SATA Slim drive in the STC-1005, loosen the screws securing the drive bay bracket from the device as shown. Install the drive with the screws provided.
3.4 STC-1205/1505 SATA Slim Drive Installation To install or replace a SATA Slim drive in the STC-1205/1505, loosen the screws securing the drive bay bracket from the device as shown. Install the drive with the screws provided.
STC-1005/ 1205/ 1505 3.5 STC-1205/1505 2.5” SATA Drive Installation To install or replace a 2.5” SATA drive in the STC-1205/1505, loosen the screws securing the drive bay bracket from the device as shown. Install the drive with the screws provided. Figure 3-8: STC-1205/1505 2.
3.6 Connecting Power An AC power adapter (19VDC, 65W) is included with the STC-1005/1205/1505. To connect power to the device, insert the pluggable terminal block on the end of the power supply into the DC power inlet as shown below. Secure the terminal block by tightening the two screws as indicated. To connect a different DC power supply to the device, loosen the screws securing the power leads to the terminal block indicated below and connect the desired power supply with polarity as shown.
STC-1005/ 1205/ 1505 Powering Up the System When DC power is turned on, the system will automatically boot up. The power switch on the IO panel is an ATX switch.To shut down the system, use the Windows shutdown procedure. To boot the system after a soft shutdown, use the ATX switch or disconnect and reconnect DC power.
This page intentionally left blank.
STC-1005/ 1205/ 1505 Important Safety Instructions For user safety, please read and follow all instructions, WARNINGS, CAUTIONS, and NOTES marked in this manual and on the associated equipment before handling/operating the equipment. X Read these safety instructions carefully. X Keep this user’s manual for future reference. X Read the specifications section of this manual for detailed information on the operating environment of this equipment.
A Lithium-type battery may be provided for backup power. Risk of explosion if battery is replaced with one of an incorrect type. Dispose of used batteries appropriately. WARNING: 28 X Never attempt to fix the equipment. Equipment should only be serviced by qualified personnel.
STC-1005/ 1205/ 1505 Getting Service Contact us should you require any service or assistance. ADLINK Technology, Inc. Address: 9F, No.166 Jian Yi Road, Zhonghe District New Taipei City 235, Taiwan ᄅؑקխࡉ৬ԫሁ 166 ᇆ 9 ᑔ Tel: +886-2-8226-5877 Fax: +886-2-8226-5717 Email: service@adlinktech.com Ampro ADLINK Technology, Inc. Address: 5215 Hellyer Avenue, #110 San Jose, CA 95138, USA Tel: +1-408-360-0200 Toll Free: +1-800-966-5200 (USA only) Fax: +1-408-360-0222 Email: info@adlinktech.
ADLINK Technology, Inc. (French Liaison Office) Address: 6 allée de Londres, Immeuble Ceylan 91940 Les Ulis, France Tel: +33 (0) 1 60 12 35 66 Fax: +33 (0) 1 60 12 35 66 Email: france@adlinktech.com ADLINK Technology Japan Corporation Address: ͱ101-0045 ᵅҀ䛑गҷ⬄ऎ⼲⬄䤯 ⬎ފ3-7-4 ⼲⬄ 374 ɛɳ 4F KANDA374 Bldg. 4F, 3-7-4 Kanda Kajicho, Chiyoda-ku, Tokyo 101-0045, Japan Tel: +81-3-4455-3722 Fax: +81-3-5209-6013 Email: japan@adlinktech.com ADLINK Technology, Inc.
