Nomad Digital R4600 GEN2 Communications Control Unit User’s Manual DOC#NCP-R4600 GEN2-SOW
Revision History Revision Change Date 0.1 Initial version Nov.
Contents 1 NDL requirements ..................................................................................................................................... 4 Power ................................................................................................................................................. 4 Expansion ........................................................................................................................................... 5 ECC Memory option .......................
1 NDL requirements Power Floating wide range DC input to support EN50155:2017 and ignition input to control system power plus initiate graceful operating system shutdown. The ignition control signal is to be referenced to input supply voltage as requested by NDL and is detailed in Section 2 Product Specifications. A flow diagram is shown under 6.2 power ignition control. A TVS diode is fitted between the plus and minus power inputs, there are no voltage clamping devices between these inputs and the chassis.
Expansion The unit is equipped with four mPCIe slots, two m.2 slots from I/O board and one m.2 slot from the motherboard as detailed in Section 2. Two m.2 slots from the modem area (Section 5.1 location M.2-1 & M.2-2) provide USB 3.0 signaling and one m.2 from the motherboard provides USB3.0 and SATA signaling for a storage device. Two mPCIe slots with USB 3.0 signaling (Section 5.
Pin # Location 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 mPCIe slot 5 & 6 USB 2.
1.2.2 Pin-out of M.2 slots M.
system will be supplied without storage media. Expansion slots M.2-1, M.2-2 and mPCIe-3 to mPCIe-6 can be powered off or on using the built in PCA-9555 GPIO expander. The GPIO expander is controlled using i2c commands. By default expansion slots M.2-1, M.2-2 and mPCIe-3 to mPCIe-6 are powered on when the system power is on. User defined LEDs labelled U1 to U8 are controlled using i2c commands to the built in PCA-9555 GPIO expander.
2 Product Specifications R4600 GEN2 ES2 system specifications Processor Intel® Core™ i5-6440EQ Processor, Base frequency 2.70GHz, Burst 3.4GHz Chipset Intel QM170 Chipset Memory Dual Channel DDR4 2133 8GB or 16GB by SODIMM (Up to 32GB) Storage 1 x 2.5” Removable drive bay 1 x accessible CFast socket 1 x Internal M.
(16.8V to 137.5V, EN50155 compliant) -154V reverse polarity protection 161V(+-2%) over-voltage protection A TVS diode is fitted between the plus and minus power inputs, there are no voltage clamping devices between these inputs and the chassis. A standard 1000VAC voltage withstand test with shorted plus – minus is supported.
EN50155:2017, EN61373:2010 Environmental EN60068-2-1:2007, EN60068-2-2:2007 EN60068-2-27:2009, EN60068-2-30:2005, EN60068-2-64:2008 RoHS 2.
3 System Block Diagram DOC#NCP-R4600 GEN2-SOW
4 Mechanical Drawing reference External chassis drawings and mounting plate Chassis rear view Chassis top view Chassis front view DOC#NCP-R4600 GEN2-SOW
Torx screw location Front panel labelling Front panel design with logo DOC#NCP-R4600 GEN2-SOW
5 Internal drawings and Warning statement Drawing of M.2/mPCIe area and PCB designations Acc. to FCC rule 15.
Suggested Pigtail routing Optional Pigtail Accessory kit 1 P/N : 91-95261-000E 12x MHF4 Pigtail Optional Pigtail Accessory kit 2 P/N : 91-95261-010E 4x MHF4 Pigtail and 4x U.
6 Design Details Power ignition control Note :BIOS will provide Power off delay time option: 5,10,15 minutes.
7 Connector details and Pin out External Connectors Main power and Ignition input M12 LAN Port port (X-coded) from external cable side M12 LAN Port port (X-coded) from board side DOC#NCP-R4600 GEN2-SOW Pin Signal name 1 MDI_T_P0 2 MDI_T_N0 3 MDI_T_P1 4 MDI_T_N1 5 MDI_T_P3 6 MDI_T_N3 7 MDI_T_N2 8 MDI_T_P2
USB 3.0 Ports USB 3.
8 Additional data Battery – not installed due to long term reliability concerns, system will lose date and time information when powered off, but will not show any error messages relating to a low or missing CMOS battery USB Port Power – The USB ports provide power to support external USB devices, these are protected against overload with a self-recovering poly fuse. DVI Port Power – The DVI port provides power output and this is protected against overload with a selfrecovering poly fuse.
Important Safety Instructions For user safety, please read and follow all instructions, WARNINGS, CAUTIONS, and NOTES marked in this manual and on the associated equipment before handling/operating the equipment. � Read these safety instructions carefully. � Keep this user’s manual for future reference. � Read the specifications section of this manual for detailed information on the operating environment of this equipment.
