PCIe-2602 3G-SDI Audio/Video Capture Card User’s Manual Manual Rev.: 3.00 Revision Date: Aug. 23, 2013 Part No: 50-11251-1010 Advance Technologies; Automate the World.
Revision History ii Revision Release Date Description of Change(s) 2.00 June 28, 2013 Initial release 3.00 Aug.
PCIe-2602 Preface Copyright 2013 ADLINK Technology, Inc. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.
Conventions Take note of the following conventions used throughout this manual to make sure that users perform certain tasks and instructions properly. Additional information, aids, and tips that help users perform tasks. NOTE: CAUTION: WARNING: iv Information to prevent minor physical injury, component damage, data loss, and/or program corruption when trying to complete a task.
PCIe-2602 Table of Contents Revision History...................................................................... ii Preface .................................................................................... iii List of Figures ....................................................................... vii List of Tables.......................................................................... ix 1 Introduction ........................................................................ 1 1.1 Overview.........
A Appendix: ViewCreator Pro Utility ...................................27 A.0.1 Devices Panel........................................................... 28 A.0.2 Tool Panel ................................................................ 29 A.0.3 Display Panel............................................................ 36 A.0.4 Status Panel ............................................................. 36 A.0.5 Display Menu ............................................................ 37 A.0.
PCIe-2602 List of Figures Figure 1-1: PCIe-2602 Schematic Diagram ....................................... 6 Figure 1-2: PCIe-2602 Board Layout ................................................. 7 Figure 1-3: I/O & Indicator Panel........................................................ 7 Figure 1-4: SDI Connector ................................................................. 8 Figure 1-5: RS-485 Connector ........................................................... 8 Figure 1-6: DI/O Connector.............
This page intentionally left blank.
PCIe-2602 List of Tables Table Table Table Table Table 1-1: 1-2: 1-3: 1-4: 1-5: Table Table Table Table Table Table Table Table Table Table Table Table Table 1-6: 1-7: 1-8: 1-9: 1-10: 1-11: A-1: A-2: A-3: A-4: A-5: A-6: A-7: List of Tables Board Layout Legend ...................................................... 7 SDI Connector Pin Assignment ....................................... 8 RS-485 Connector Pin Assignment ................................. 9 D I/O Connector Pin Assignments ..................
This page intentionally left blank.
PCIe-2602 1 Introduction 1.1 Overview The PCIe-2602 3G-SDI Audio/Video Capture Card, based on the PCI Express® x4 interface, enables acquisition of 2 channels 3G-SDI, low latency, and raw video data signals up to 1920x1080P/60fps (frames per second).
a wide variety of applications, including medical imaging and intelligent video surveillance or analytics. The PCIe-2602 Function Library Reference can be downloaded from the product’s pages at http://www.adlinktech.com NOTE: 1.4 Specifications The PCIe-2602 provides 2 BNC connectors that support 2 channels of video and embedded audio, with maximum video data throughput of 2.97Gb/s, with 1.485G and 270M bps supported, and RS-485 and digital I/O simplify connection with other devices. 1.4.
PCIe-2602 Item Specification SD Interlace pattern 525i(720x486i@59.94/60Hz), 625i(720x576i@50Hz) HD interlace pattern 1080i50(1920x1080i@50Hz), 1080i60(1920x1080i@59.94/60Hz) HD progressive pattern 720p24(1280x720p@24Hz), 720p25(1280x720p@25Hz), 720p30(1280x720p@30Hz), 720p50(128x720p@50Hz), 720p60(128x720p@59.94/60Hz), 1080p24(1920x1080p@23.98/24Hz, 1080p25(1920x1080p@25Hz), 1080p30(1920x1080p@30Hz), 1080p50(1920x1080p@50Hz), 1080p60(1920x1080p@59.
NOTE: 1.4.3 1.4.4 If the input source is 720p30, 8/10 bit 4:4:4, the PCIe-2602 can only capture the video signal without audio signal. In ViewCreator Pro, adjust Video Format and Color Format to display the image normally. Format in the API GetDetectedSensorFormat (UINT Number, int& Format) will return -1 when the input source is 720p30, 8/10 bit 4:4:4. Power Consumption Test Item Value DC 3.3V 1.5A DC 12V 1.
PCIe-2602 Parameter Min. Type Max. Input High Threshold for WAKE#, PERST# , +2.0V SMCLK and SMDAT +3.45V Input Low Threshold for WAKE#, PERST#, SMCLK and SMDAT +0.8V -0.3V Comment Digital Input Number of Channels 4 digital inputs Input Resistance 1 KΩ Input High Threshold 2V 12V Input Low Threshold 0V 0.8V Input power dissipation 0W 0.
1.4.5 Physical Dimensions 149mm x 111.15mm Operating Temperature 0˚C to 60˚C Storage Temperature -20°C to 80°C Humidity 5%~95% (non-condensing) Safety Compliance CE & FCC 1.5 Schematics, I/O and Indicators All dimensions shown are in mm NOTE: 162.74 149 98.4 111.15 126.
PCIe-2602 A B C Figure 1-2: PCIe-2602 Board Layout A D I/O B SDI C RS-485 Table 1-1: Board Layout Legend I/O and indicator panel elements are labeled as follows Figure 1-3: I/O & Indicator Panel Introduction 7
1.5.1 SDI Connector 1 2 Figure 1-4: SDI Connector Pin Function Type 1 SDI signal Input 2 SDI signal GND Reference ground Table 1-2: SDI Connector Pin Assignment 1.5.2 RS-485 Connector The PCIe-2602 RS-485 connector is a DSUB-9 male configuration.
PCIe-2602 Pin Function Type 1 RS485 Channel 1 data+ Dual direction 2 RS485 Channel 1 data- Dual direction 3 RS485 Channel 2 data+ Dual direction 4 RS485 Channel 2 data- Dual direction 5 Digital GND Reference ground 6 Digital GND Reference ground 7 Digital GND Reference ground 8 Digital GND Reference ground 9 Digital GND Reference ground Table 1-3: RS-485 Connector Pin Assignment 1.5.
Pin Function Type 6 DI2+ Digital Input channel 2 non-invert pin 7 DI0- Digital Input channel 0 invert pin 8 DI3+ Digital Input channel 3 non-invert pin 9 DO0 Digital Output channel 0 10 GND Digital Ground 11 DO1 Digital Output channel 1 12 GND Digital Ground 13 DO2 Digital Output channel 2 14 Clamp Digital Output Darlington IC clamping voltage 15 DO3 Digital output channel 3 Table 1-4: D I/O Connector Pin Assignments 10 Introduction
PCIe-2602 External access to the DI/O connector can be provided using ADLINK's separately available D-sub connector cable with external bracket (ADLINK part number: 30-25013-0000).
15 8 9 1 Figure 1-8: D-sub Connector Cable Exterior Connector 12 Pin Function Type 1 DI3- Input 9 DI0+ Input 2 DI2- Input 10 DI1+ Input 3 DI1- Input 11 DI2+ Input 4 DI0- Input 12 DI3+ Input 5 DO0 Output 13 GND DO Ground Introduction
PCIe-2602 Pin Function Type 6 DO1 Output 14 GND DO Ground 7 DO2 Output 15 DO clamp DO Power 8 DO3 Output Table 1-5: D-sub Connector Cable Exterior Connector Pin Assignments 1.5.4 LED Indicators Four LED indicators on the I/O panel indicate SDI signal connection and status. Figure 1-9: LED Indicators LEDs 0 and 1 indicate status of vertical synchronization signals, while 2 and 3 confirm data verification, as follows.
LED 1 LED 3 Description Blinking On The input signal is identified and channel 1 is functioning normally Off No input is detected or the input signal cannot be identified. The connection or cable should be checked, or the input signal format determined to be SDI. Off Table 1-7: LEDs 1 and 3 Indicator Legend NOTE: 14 If a signal is received but unidentified, please check the SDI signal format according to Section 1.4.2 Video & Audio.
PCIe-2602 1.5.5 Switch Settings Switches for digital I/O and card ID settings, allowing identification of individual cards in a multi-card system, are located as follows.
Card ID Slider 1 Slider 2 Slider 3 Slider 4 15 on on on on 14 off on on on 13 on off on on 12 off off on on 11 on on off on 10 off on off on 9 on off off on 8 off off off on 7 on on on off 6 off on on off 5 on off on off 4 off off on off 3 on on off off 2 off on off off 1 on off off off 0 off off off off Table 1-9: Card ID Switch Settings (S1) DI Channel DI Status Slider Setting DI0 Pulled high to +5V 1 On DI0 Low
PCIe-2602 DI Channel DI Status Slider Setting DO0 Pulled high to +5V 1 On DO0 Low 1 Off DO1 Pulled high to +5V 2 On DO1 Low 2 Off DO2 Pulled high to +5V 3 On DO2 Low 3 Off DO3 Pulled high to +5V 4 On DO3 Low 4 Off Table 1-11: D I/O Switch Settings (S5) 1.5.6 Digital I/O Connections Function block diagrams and connection examples for digital I/O settings follow.
In the following, varying situations are illustrated in which channel # of digital input is connected, where # is 0 to 3. PCIe-2602 +5V 330 +3.
PCIe-2602 PCIe-2602 +5V 330 +3.
Digital Output Figure 1-14: PCIe -2602 Digital Output Functional Block Diagram In the following, varying situations are illustrated in which channel # of digital output is connected, where # is 0 to 3.
PCIe-2602 PCIe-2602 Clamp +5V User VCC DC User Device Load Darlington Driver S5 User DI DO# (From FPGA) DO Out# (To connector) GND API (DO Output) DO Out# to Connector 1 Low(0V) 0 High Z Figure 1-15: Sinking DO: Slider # of Switch 5 is OFF Introduction 21
PCIe-2602 Clamp +5V 330 Darlington Driver S5 User DI DO# (From FPGA) DO Out# (To connector) User Device Load GND API(DO Output) DO Out# to Connector 1 Low (0V) 0 High (+5V) Figure 1-16: Sourcing DO: Slider # of Switch 5 is ON 1.5.7 RS-485 Connection PCIe-2602 supports RS-485 protocol To avoid signal reflections, each bus segment must be blanked at its physical beginning and end with the characteristic impedance.
PCIe-2602 recommended value. Detailed connection of the Rt is as follows. PCIe-2602 supports BUS topology.
This page intentionally left blank.
PCIe-2602 2 Getting Started 2.1 Unpacking Checklist Before unpacking, check the shipping carton for any damage. If the shipping carton and/or contents are damaged, inform your dealer immediately. Retain the shipping carton and packing materials for inspection. Obtain authorization from your dealer before returning any product to ADLINK. Ensure that the following items are included in the package.
7. Power up the computer. The PCIe-2602 can be installed in a PCI Express x4, x8, or pcie PCIe x16 slot.
PCIe-2602 Appendix A ViewCreator Pro Utility The included ViewCreator Pro utility provides simple yet powerful setup, configuration, testing, and debugging of your vision system. NOTE: ViewCreator Pro is available for Windows XP/7/8 systems only, with recommended screen resolution exceeding 800x600. Microsoft .NET Framework 3.
The ViewCreator Pro interface provides a variety of panels and toolbars, allowing comprehensive task performance in all areas of function. A.0.
PCIe-2602 A.0.2 Tool Panel Tool Button Function ContinueGrab Toggles continuous acquisition of images . Captures a single image SnapShot . Hide/Show Image Toggles display of the image . FitSize Resizes the image to fit the display area . Restores the image to original size OriginalSize . ZoomIn Increases image closeup . Decreases image closeup ZoomOut . FocusCross .
Tool HSI Conversion YCbCr Enable Image Flip Button Function Opens a window showing the HSI values along . the selected line on the image Transforms the image to YCbCr color space, . toggling YCbCr Enable/Y Enable (CbCr=128)/ CbCr Enable (Y=0)/YCbCr Disable Toggles No Flip/Flip X axis (horizontal)/Flip Y axis (vertical) . Record Toggles Record function (Function supports only 4:2:2 8-bit video input) .
PCIe-2602 ViewCreator Pro Utility 31
When acquisition is complete, the background color of the window changes to black. X-axis size is the width of the entire image.
PCIe-2602 If the image is chromatic, three curves, individually representing red, green, and blue are shown.
If the color format of captured image is YUV, three curves individually representing Y, U, and V are shown.
PCIe-2602 FocusValue Tools Tool Button Function Zoom In Increases closeup on the area in the FocusValue window bound by the green rectangle, which can be resized by dragging the side borders Differential Displays slope of the line for the area in the FocusValue window bound by the green rectangle, which can be resized by dragging the side borders Show/Hide Red Values Toggles display of red pixel values. Show/Hide Green Values Toggles display of green pixel values.
A.0.3 Display Panel Captured images are displayed on this panel as shown. A.0.4 Status Panel Displays image acquisition, signal, and image statistics, as shown.
PCIe-2602 A.0.5 Display Menu Allows selection of desired video format based on SDI(BNC). The SDI menu is shown open as an example. Figure A-4: SDI Display Menu Format Resolution 525i 29.97/30 fps 720 x 486 625i 25 fps 720 x 576 720p 24 fps 1280 x 720 720p 25 fps 1280 x 720 720p 30 fps 1280 x 720 720p 50 fps 1280 x 720 720p 59.
Format Resolution 1080i 25 fps 1920 x 1080 1080i 29.97/30 fps 1920 x 1080 1080p 23.98/24 fps 1920 x 1080 1080p 25 fps 1920 x 1080 1080p 30 fps 1920 x 1080 1080p 50 fps 1920 x 1080 1080p 59.97/60 fps 1920 x 1080 Table A-5: SDI (BNC) Available Formats A.0.6 Color Format Menu Sets the captured image to the selected color format.
PCIe-2602 A.0.8 Image Size Menu Top-down Enables top-down image display. Top-down function, when enabled, may improve capture efficency in computers experiencing low frame rate due to performance. Auto Detect Automatically detects image resolution A.0.9 Tool Menu DI/O Sets and retrieves digital input/output status, select digital output and digital input conditions.
Figure A-5: DI/O Dialog A.0.10 Help Menu About Device Displays card ID, hardware version, firmware version, driver version, and utility version information.
PCIe-2602 Figure A-6: About Device Dialog ViewCreator Pro Utility 41
This page intentionally left blank.
PCIe-2602 Appendix B PCIe-2602 Benchmark PCIe-2602 delivers 2-CH 1080P/60 fps raw video data requiring PCIe X4 or more. If bandwidth is insufficient, abnormal images may be generated or frames lost. In some systems, the bandwidth of PCIe slots may be shared. When frame capture rate deviates from that expected, check the PCIe slot setting in the computer user manual or BIOS. B.1 Recommended System Configuration CPU Intel i5 or above RAM 4GB OS Win XP/7/8 (Microsoft .NET Framework 3.
B.2.2 Platform MXC-6300 CPU Intel® Core™ i7 3610QE 2.30GHz Memory 8GB X2 OS WinXP Professional 32 bit Input signal 1080p 60fps,YUV 4:2:2, 10 bit Card# 0 (PCIe x8 slot) 1 (PCIe x8 slot) Channel# 0 1 0 1 Captured Frame Rate (fps) 60 60 60 60 B.2.3 Test 3 Motherboard GIGA-X58A-UD3R CPU Intel® Core™ i7 920 2.
PCIe-2602 Channel Number 0 1 0 1 Captured Frame Rate (fps) 60 60 60 60 B.2.5 Test 5 Motherboard ASUS P8P67 CPU Intel® i5 2400 Memory 2GB X 1 OS Win7 Pro 32 bit Input signal 1080p 60fps,YUV 4:2:2, 10 bit Card ID 0 (PCIe x16 slot) NA Channel Number 0 1 NA NA Captured Frame Rate (fps) 60 60 NA NA The PCIe PCIe x16 slot setting is changed to “X4 mode” via BIOS. NOTE: B.2.6 Test 6 Motherboard GIGA-X58A-UD7 CPU Intel® Core™ i7 950 3.
This page intentionally left blank.
PCIe-2602 Important Safety Instructions For user safety, please read and follow all instructions, WARNINGS, CAUTIONS, and NOTES marked in this manual and on the associated equipment before handling/operating the equipment. X Read these safety instructions carefully. X Keep this user’s manual for future reference. X Read the specifications section of this manual for detailed information on the operating environment of this equipment.
X Never attempt to fix the equipment. Equipment should only be serviced by qualified personnel. A Lithium-type battery may be provided for uninterrupted, backup or emergency power. Risk of explosion if battery is replaced with one of an incorrect type. Dispose of used batteries appropriately.
PCIe-2602 Getting Service Contact us should you require any service or assistance. ADLINK Technology, Inc. Address: 9F, No.166 Jian Yi Road, Zhonghe District New Taipei City 235, Taiwan ᄅؑקխࡉ৬ԫሁ 166 ᇆ 9 ᑔ Tel: +886-2-8226-5877 Fax: +886-2-8226-5717 Email: service@adlinktech.com Ampro ADLINK Technology, Inc. Address: 5215 Hellyer Avenue, #110, San Jose, CA 95138, USA Tel: +1-408-360-0200 Toll Free: +1-800-966-5200 (USA only) Fax: +1-408-360-0222 Email: info@adlinktech.com ADLINK Technology (China) Co.
ADLINK Technology, Inc. (French Liaison Office) Address: 15 rue Emile Baudot, 91300 Massy CEDEX, France Tel: +33 (0) 1 60 12 35 66 Fax: +33 (0) 1 60 12 35 66 Email: france@adlinktech.com ADLINK Technology Japan Corporation Address: ͱ101-0045 ᵅҀ䛑गҷ⬄ऎ⼲⬄䤯 ⬎ފ3-7-4 ⼲⬄ 374 ɛɳ 4F KANDA374 Bldg. 4F, 3-7-4 Kanda Kajicho, Chiyoda-ku, Tokyo 101-0045, Japan Tel: +81-3-4455-3722 Fax: +81-3-5209-6013 Email: japan@adlinktech.com ADLINK Technology, Inc.
