GIE64+ 4-CH PoE GigE Vision Interface Card User’s Manual Manual Rev.: 2.00 Revision Date: Feb. 24, 2012 Part No: 50-11245-1000 Advance Technologies; Automate the World.
Revision History ii Revision Release Date 2.00 Feb.
GIE64+ Preface Copyright 2012 ADLINK Technology Inc. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer. Disclaimer The information in this document is subject to change without prior notice in order to improve reliability, design, and function and does not represent a commitment on the part of the manufacturer.
Conventions Take note of the following conventions used throughout this manual to make sure that users perform certain tasks and instructions properly. Additional information, aids, and tips that help users perform tasks. NOTE: CAUTION: WARNING: iv Information to prevent minor physical injury, component damage, data loss, and/or program corruption when trying to complete a task.
GIE64+ Table of Contents Revision History...................................................................... ii Preface .................................................................................... iii List of Figures ....................................................................... vii List of Tables.......................................................................... ix 1 Introduction ........................................................................ 1 1.1 Overview............
This page intentionally left blank.
GIE64+ List of Figures Figure 2-1: Figure 2-2: Figure 2-3: Figure 2-4: Figure 2-5: GIE64+ Schematic Diagram ............................................ 5 GIE64+ Board Layout ...................................................... 6 RJ-45 Ethernet Connector ............................................... 6 Status LEDs..................................................................... 7 Power Connector .............................................................
This page intentionally left blank.
GIE64+ List of Tables Table Table Table Table 2-1: 2-2: 2-3: 2-4: List of Tables Board Layout Legend ...................................................... 6 RJ-45 Ethernet Port Connector Signals........................... 7 Status LED Legend ......................................................... 8 Power Connector Pin Assignments .................................
This page intentionally left blank.
GIE64+ 1 Introduction 1.1 Overview ADLINK's GIE64+ is a PCI Express® x4 lane, PoE (Power over Ethernet) frame grabber with support for four independent Gigabit Ethernet ports. Multiple Gigabit Ethernet Vision device connections are supported for standard Gigabit Ethernet Vision data transfer rates of up to 1000 Mb/s. The GIE64+ features not only PoE, combining power supply and signal into a single cable, but also IEEE 1588 (precise time protocol), enabling synchronization with multi-camera acquisition.
1.4 Specifications 1.4.1 Power over Ethernet Port The GIE64+ Power over Ethernet specification supports 2 X Four fully-integrated Gigabit Ethernet Media Access Control (MAC) and physical layer (PHY) ports X Full controller compliance with IEEE 802.3.af standard for maximum 15.4 watts, with power up to 48 V over existing CAT-5 Ethernet infrastructure, with no modifications required X Standard IEEE 802.3 Ethernet interface provided for 1000BASE-T, 100BASE-TX, and 10BASE-T applications (802.3, 802.
GIE64+ 1.4.2 General Specifications Function Description Power Requirements X Input voltage: 12 VDC, (w/ PC system power) X Input current: Max. 6 A @ 12 VDC (supporting up to 4 ports at 15.4 W per PoE port) PCI Express PCIe X4 ports 1 port PCIe X4, for GigE Vision Differential Output Peak +0.8 V to +1.2 V to Peak Voltage Differential Input Peak to Peak Voltage +0.175 V to +1.2 V Input voltage for PERST#, WAKE#, and SMBus -0.75 V to +4.05 V Gigabit Ethernet LAN chip Intel® 82574L, PCIe v1.
X Always disconnect the power cord from the chassis when working on the device, and do not reconnect while the power switch is on, since sudden power input can damage sensitive electronic components X Only authorized and experienced electronics personnel should open the chassis X Always ground yourself to remove any static electric charge before touching EOS, the device is very sensitive to static electric charges; use a grounding wrist strap at all times, and place all electronic components on a static-di
GIE64+ 2 Getting Started All dimensions shown are in mm NOTE: 111.
D C B A Figure 2-2: GIE64+ Board Layout A PCIe lane B RJ-45 Ethernet Ports C Status LED D Power Connector Table 2-1: Board Layout Legend 2.0.
GIE64+ Pin Signal 1 MDI0+ (PoE_DC48V) 2 MDI0- (PoE_DC48V) 3 MDI1+ (PoE_DC0V) 4 MDI2+ (PoE_DC48V) 5 MDI2- (PoE_DC48V) 6 MDI1- (PoE_DC0V) 7 MDI3+ (PoE_DC0V) 8 MDI3- (PoE_DC0V) Table 2-2: RJ-45 Ethernet Port Connector Signals 2.0.
The GIE64+ provides four yellow LEDs to indicate operating conditions of the four PoE ports, as shown, with corresponding status as follows. LED Status 1 ON: Port 1 PoE On OFF: Port 1 PoE Off 2 ON: Port 2 PoE On OFF: Port 2 PoE Off 3 ON: Port 3 PoE On OFF: Port 3 PoE Off 4 ON: Port 4 PoE On OFF: Port 4 PoE Off Table 2-3: Status LED Legend 2.0.
GIE64+ 3 Hardware Installation The following describes installation of the GIE64+ module on the PCI express bus. 1. Remove the computer cover according to the computer manual.. NOTE: A vacant PCI express slot is required for installation of the GIE64+ module; if none is available, remove a PCI express board and note the slot number. 2. Remove the slot cover (if any), retaining the fixing screw. 3. Carefully position the GIE64+ in the selected PCI express slot.
This page intentionally left blank.
GIE64+ Important Safety Instructions For user safety, please read and follow all instructions, WARNINGS, CAUTIONS, and NOTES marked in this manual and on the associated equipment before handling/operating the equipment. X Read these safety instructions carefully. X Keep this user’s manual for future reference. X Read the specifications section of this manual for detailed information on the operating environment of this equipment.
X Never attempt to fix the equipment. Equipment should only be serviced by qualified personnel. A Lithium-type battery may be provided for uninterrupted, backup or emergency power. WARNING: X 12 Risk of explosion if battery is replaced with one of an incorrect type. Dispose of used batteries appropriately.
GIE64+ Getting Service Contact us should you require any service or assistance. ADLINK Technology, Inc. Address: 9F, No.166 Jian Yi Road, Zhonghe District New Taipei City 235, Taiwan ᄅؑקխࡉ৬ԫሁ 166 ᇆ 9 ᑔ Tel: +886-2-8226-5877 Fax: +886-2-8226-5717 Email: service@adlinktech.com Ampro ADLINK Technology, Inc. Address: 5215 Hellyer Avenue, #110, San Jose, CA 95138, USA Tel: +1-408-360-0200 Toll Free: +1-800-966-5200 (USA only) Fax: +1-408-360-0222 Email: info@adlinktech.com ADLINK Technology (China) Co., Ltd.
ADLINK Technology, Inc. (French Liaison Office) Address: 15 rue Emile Baudot, 91300 Massy CEDEX, France Tel: +33 (0) 1 60 12 35 66 Fax: +33 (0) 1 60 12 35 66 Email: france@adlinktech.com ADLINK Technology Japan Corporation Address: ͱ101-0045 ᵅҀ䛑गҷ⬄ऎ⼲⬄䤯 ⬎ފ3-7-4 ⼲⬄ 374 ɛɳ 4F KANDA374 Bldg. 4F, 3-7-4 Kanda Kajicho, Chiyoda-ku, Tokyo 101-0045, Japan Tel: +81-3-4455-3722 Fax: +81-3-5209-6013 Email: japan@adlinktech.com ADLINK Technology, Inc.
