IMX-3000 Rugged Handheld Device User’s Manual Manual Revision: 0.2 Revision Date: 07.08.2014 Part No.
Revision History Version 0.10 Date 2013/11/28 Description Preliminary release Copyright 2013 ADLINK Technology, Inc. All Rights Reserved The information in this document is subject to change without prior notice in order to improve reliability, design, and function and does not represent a commitment on the part of the manufacturer.
Table of Contents Revision History....................................................................................................................................2 Table of Contents .................................................................................................................................3 Notices..................................................................................................................................................4 Product Notes .........................
Notices Product Notes For user safety, please read and follow all instructions, WARNINGS, CAUTIONS, and NOTES marked in this manual and on the associated equipment before handling/operating the equipment. To avoid damaging the product due to improper operation, please read the manual thoroughly before use. IMX-3000 working temperature: For 1D and 2D model, the operating temperature range (discharging) is -10°C to 50°C. For CCD model, the operating temperature range (discharging) is -10°C to 50°C.
Important Safety Instructions Read and follow all instructions marked on the product and in the documentation before you operate your system. Retain all safety and operating instructions for future use. Please read these safety instructions carefully. Please keep this User‘s Manual for later reference. The equipment can be operated at an ambient temperature of 50ºC for discharge; 40ºC for charge. The equipment should be operated only from the type of power source indicated on the rating label.
FCC Warning statement a. for FCC 15b devices This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
requirements, and should be avoided. Vehicle mounted external antenna (Optional, if available) A minimum separation distance of 20cm must be maintained between the user/bystander and the vehicle mounted external antenna to satisfy FCC RF exposure requirements. RF exposure information (SAR) This GPS Controller meets the government's requirements for exposure to radio waves.
Quick guide 1 IMX-3000 layout 1 Power key 2 LCD & Touch panel 7 8 Proximity sensor Receiver 13 Camera and Flash LED 14 Speaker 3 4 5 6 9 10 11 12 Scan window Lanyard Headset slot USB port 15 16 17 18 Function key area Microphone Power LED Light sensor 2 Battery cover Volume up Volume down NFC antenna Package of Contents The IMX-3000 is packaged with the components listed below.
3 Installing SIM card and Micro SD card Insert the SIM card or Micro SD card in the correct direction. Lock the SIM card or Micro SD card cover after inserting the SIM card.
4 Install Battery There ways to charge the battery. 4.1 USB Charge via DC adaptor: Connect the USB connector from the DC adapter to the 4.2 USB socket of the IMX-3000 as shown. Insert the correct plug for your region into the DC adapter and plug it into the wall socket to begin charging. Charging Cradle: Connect the DC adapter to the charging cradle to charge the IMX-3000 and secondary battery simultaneously. 4.
Getting Start 1 Android Wizard in first start 1.1 1.2 In first start IMX-3000, the Android Wizard will pop up. It shows how to set Android APP in to Home screen. Release the page by pressing OK button. 1.3 1.4 Press Applications icon, another wizard will shows up. Release the page by pressing OK button. 1.5 Unlock screening The screen will lock in first start or resume by stand by mode, unlock the screen by press and hold the lock icon and then drag it to unlock icon.
2 Key Definition Icon Keys Description HOME Press this key to go back to the Android home screen. MENU Press this key to open a menu with items that affect the current screen or application BACK 3 Press this key to go back to the previous screen you were working in. SEARCH Press this key to open Google search for searching your phone, web and the applications. SCAN When the barcode reader is enabled, press start barcode scanning. to Status Indicator 3.
Connection 2 Connecting to Wi-Fi Network on the Home screen > Settings (1) Touch (2) Slide the switch to turn on Wi-Fi. > Wi-Fi. -> (3) The IMX-3000 scans for available Wi-Fi networks and displays their names. Secure networks are indicated with a lock icon. (4) Touch a Wi-Fi network to connect to it. You will be prompted to enter a password or other credentials if the network is secured.
3 Connecting to Bluetooth Network 3.1 Touch on the Home screen > Settings > Bluetooth -> 3.2 Slide the switch to turn on Bluetooth. 3.3 3.4 The IMX-3000 scans for available Bluetooth clients and displays their names. Touch a Bluetooth client to pair. When Bluetooth is turning on, the notification icon will display on the status bar. You can start exchanging data with the Bluetooth device. Touch Menu to see more functions.
4 Using GPS & AGPS 4.1 4.2 4.3 Enable GPS (1) Touch on the Home screen > Settings (2) Enable GPS satellite. > Location Service Get GPS location by Wi-Fi or mobile connection. (1) Touch on the Home screen > Settings (2) Enable Google’s location service. Get GPS location in Google map. (1) Touch on the Home screen > Maps (2) Get location in Google map.
It may take several minutes for GPS to determine your location for the first time. GPS will be more time efficient after satellite locations have been saved.
5 WCDMA/GSM 5.1 Carrier information Touch on the Home screen > Settings > About phone > Status The carrier and SIM relate information can be check. 5.2 (1) (2) (3) (4) Network Signal strength Mobile network type Service state (5) (6) (7) Roaming Mobile network state IMEI Set Airplane mode (1) Touch (2) Enable Airplane mode by touching the check box. on the Home screen > Settings > More All wireless function will lose connection if airplane mode.
5.3 Enable 2G networks (1) Touch (2) settings Enable 2G networks by touching the check box. 5.4 on the Home screen > Settings > More > Mobile network 2G icon will replace 3G icon in stats bar. Set VPN (1) Touch on the Home screen > Settings (2) Set VPN by touching radio box.
6 NFC 6.1 Enable/disable NFC (1) Touch (2) Enable/Disable NFC on the Home screen > Settings > More The NFC application require to additional installation.
Using Camera on the Home screen, then > Camera Launch Camera by press Touch 1 Picture mode 1.1 Taking a picture (1) Drag the control to the Photo position (2) Frame your subject on screen (3) 1.2 Touch the onscreen Shutter Zoom in and zoom out to zoom in or zoom out. Drag the scroll 1.3 icon to take a picture. Setting Flash mode (1) Press on the screen. (2) Press to set flash mode.
1.4 Setting storage location (1) Press on the screen. (2) Press > Storage Location to set picture/video storage location. Internal storage means EMMC storage. External storage means Micro SD card. 1.5 Setting picture size (1) Press on the screen. (2) Press > Picture size. (3) (4) Press < or > to select picture size. Picture size Items 1.
(3) Press < or > to select picture quality. Super fine Jepg 100% Jepg 95% Jepg 85% Jepg 75% Jepg 65% 1.7 1.8 Setting ZSL ZSL means zero shutter lag. (1) Press on the screen. (2) Press > ZSL to set ZSL on or off. Resetting camera setting Reset camera settings to factory default. (1) Press on the screen. (2) Press > Reset to defaults.
2 Video mode 2.1 Shooting a video (1) Drag the control to the Video position (2) Frame your subject on screen 2.2 2.3 (3) Touch the onscreen Start icon to start shooting a video. (4) Touch the onscreen Stop icon to stop shooting video. Setting Flash mode (1) Press on the screen. (2) Press to set flash mode. (3) The flash mode can be set to on or off. (4) Press on the screen. Setting Video quality (1) Press on the screen. (2) Press > Video quality.
System Setting on the Home screen > Settings Touch 1 About Phone View more information of IMX-3000 in About. 1.1 Status (1) (2) (3) View carrier and SIM card related information. Signal strength View wireless signal information. (4) (5) (6) (7) Mobile network type Service state Roaming IMEI (8) Wi-Fi MAC address View Wi-Fi MAC address Bluetooth address (9) 1.2 1.3 View Bluetooth MAC address. Baseband version (1) Baseband version refers Arm9.
2.3 Sleep setting Adjust the delay before the screen automatically turns off. 15 seconds 30 seconds 1 minute (default setting) minutes minutes 10 minutes 30 minutes Never 2.4 Touch key light duration Set key light duration for keypad. 1.5 seconds 6 seconds Always off Always on The IMX-3000 goes into standby mode after screen timeout in order to save battery power.
Utilities 1 Button utility The Button Utility allows the following keys to be re-defined to another key or a shortcut key for launching an application. (1) Side key – up key (2) Side key – down key (3) Search key (4) Scan key Launch Button utility by press 1.1 , then press Button Utility. Re-define key as key value (1) Press the Key radio box, and then press to launch the menu to re-define key value. (2) You may assign one of the following key to the key.
2 Reader Utility 2.1 Outlook Menu sheet Scan engine type will be auto detected. Barcode type display area Barcode content display area Soft scan key (1) Barcode Reading Trigger scan engine by pressing SCAN key or soft scan key on the screen. Align the scan light to barcode sheet to get the barcode data. The barcode type and data will display on the page. (2) Background Scan Hide Reader Utility by launch another application or press BACK/Home key. Get barcode data by press Scan key.
Press check box to enable LED notification. Green LED will turn on when good read. Sound notification Sound will play in good read. Vibration notification The vibrator will vibration when good read Prefix output code Add the prefix code in previous of barcode content. Suffix output code Add the suffix code in end of barcode content. Delimiter Add a delimiter in end of barcode content. (2) Auto Enter Add an ENTER character in the end of one scan Auto enable background scan when system boot.
Setting scan mode Mode Enable Hands Free Disable Hands Free Press Scan key then release it, align Press and hold Scan key, align the One time mode the scan line to barcode sheet to get barcode content. Press Scan key then release it, align the scan line to barcode sheet to get barcode content. Fixed interval The scan engine will be trigger continuous in each interval of 2 seconds. In this mode, the barcode data will be not check scan line to barcode sheet to get barcode content.
Technical Support Contact us should you require any service or assistance. ADLINK Technology, Inc. Address: 9F, No.166 Jian Yi Road, Zhonghe District New Taipei City 235, Taiwan 新北市中和區建一路 166 號 9 樓 Tel: +886-2-8226-5877 Fax: +886-2-8226-5717 Email: service@adlinktech.com Ampro ADLINK Technology, Inc. Address: 5215 Hellyer Avenue, #110, San Jose, CA 95138, USA Tel: +1-408-360-0200 Toll Free: +1-800-966-5200 (USA only) Fax: +1-408-360-0222 Email: info@adlinktech.com ADLINK Technology (China) Co., Ltd.
LiPPERT ADLINK Technology GmbH Address: Hans-Thoma-Strasse 11, D-68163, Mannheim, Germany Tel: +49-621-43214-0 Fax: +49-621 43214-30 Email: emea@adlinktech.com ADLINK Technology, Inc. (French Liaison Office) Address: 15 rue Emile Baudot, 91300 Massy CEDEX, France Tel: +33 (0) 1 60 12 35 66 Fax: +33 (0) 1 60 12 35 66 Email: france@adlinktech.com ADLINK Technology Japan Corporation Address: 〒101-0045 東京都千代田区神田鍛冶町 3-7-4 神田 374 ビル 4F KANDA374 Bldg.
Email: israel@adlinktech.