user manual 1
NOTES 2 39
NOTES TABLE OF CONTENTS WARNINGS Warning Caution Notice Overview How it works What it Measures Metrics Heart Rate Power Speed Distance Acceleration / Deceleration Field Position COMPONENTS OVERVIEW 4 5 5 7 7 7 8 8 8 8 9 9 9 10 Base Station Base Station Front Base Station Back and Bottom CELLS Chargers Cell Pcone T-Shirt 10 11 12 13 14 14 15 CONNECTING COMPONENTS 18 Insert cell into t-shirt Insert cell into Charger 38 4 18 19 CONNECTING COMPONENTS 19 Connecting CELL chargers Together 20 Connec
WARNINGS Carefully read and follow the safety information, precautions, and equipment warnings below. Only trained, qualified personnel should perform repairs to this equipment. WARNING Electrical voltage can cause fires, electrical shocks, burns, or other severe personal injuries. To help prevent the risk of equipment damage and personal injuries, observe the following general precautions for using and working with your system: Do not block vents.
SYNCING CELLS WARNINGS OFFLINE SYNC CAUTION NOTICE Offline Sync is transferring data from Cells to Base Station. If any of the following conditions occur, unplug the product from the electrical outlet and contact your authorized service provider. To help prevent product damage, always observe the following: The power cable, extension cord, or plug is damaged. Liquid has penetrated the equipment. CHARGERS STEPS STEP 1 Put all Cells into the chargers.
IPAD APPLICATION STARTING SESSION LIVE MONITORING ON THE FIELD ENDING A SESSION Continue through the start up screens and start your session. Select “Cells” to confirm that the assigned player cells are correct and live data is streaming. Select “Grid” and “List” to monitor your live dashboards. Tap any athlete to view a detailed athlete dashboard. When your training session is complete, stop the session from the “home” page.
IPAD APPLICATION ABOUT THE SYSTEM GETTING STARTED ON THE FIELD OVERVIEW HOW IT WORKS WHAT IT MEASURES miCoach Elite represents the latest advancement in performance monitoring. The state-of-the-art system gives athletes and teams a powerful, yet easy to use tool to help them achieve and maintain peak physical performance and gain an edge on their competition.
ABOUT THE SYSTEM CENTRAL WEB SYSTEM METRICS HEART RATE POWER During a training session, a coach can use the live dashboard to monitor heart rate recovery making sure not to begin the next training interval until the majority of athletes are ready. This is a precise measure of how hard the athlete is working. Power training is widely used in cycling where it has been possible to measure with a meter on the bike.
CENTRAL WEB SYSTEM ABOUT THE SYSTEM GETTING STARTED ON THE WEB METRICS DISTANCE The distance an athlete runs during a game or scrimmage can vary. A real-time measure of distance allows a coach to set individual or team targets for distance and ensure that all athletes meet their goals. During or at the end of a scrimmage, a coach can use the live app to check distance covered. Athletes that fall short of the target will continue to train.
COMPONENTS OVERVIEW BASE STATION SHUTTING DOWN BASE HARD RESET FORCE SHUTDOWN Using of Hard Reset is not recommended, only when system seems stuck and not responding to normal operation. Using of Force Shutdown is not recommended, to use only when the system is stuck. Press the Reset Button on back of the The Base is a portable receiver that collects data from up to 30 Cells and can transmit that data in real-time to the miCoach Elite Dash via WiFi.
SHUTTING DOWN BASE COMPONENTS OVERVIEW NORMAL SHUTDOWN BASE STATION FRONT Normal Shutdown should always be used when you want to turn off the system. If shutdown is rejected (Power Button blinks 3 times red), you might need to wait for the training session to finish. PCONE ANTENNA INPUT For connecting pCone antenna. Short Press the Power Button PCONE ANTENNA LED , it will start blinking yellow. Shutting down takes about a minute. 30 Indicates pCone antenna status.
COMPONENTS OVERVIEW BASE STATION LED’S CELLS CHARGERS LED BASE STATION BACK AND BOTTOM BACK SIDE RESET BUTTON USB PORTS For connecting Cells Chargers USB cable. Only for the Customer Support usage. ETHERNET CABLE PORT OFF SOLID GREEN SOLID RED DISCONNECTED No chargers connected to the Base Station. 2 CHARGERS 2 charger units connected to the Base Station. SYNC ERROR An error occurred while synchronizing data from Cells. Contact Customer Support if this persists.
BASE STATION LED’S COMPONENTS OVERVIEW PCONE ANTENNA LED CELLS CHARGERS CELL CHARGING INDICATOR 28 OFF SOLID GREEN SOLID YELLOW SOLID RED DISCONNECTED No pCone antenna attached. READY pCone antenna is attached and ready to start session. SOFTWARE UPDATE pCone antenna software update, please wait until it’s finished. INVALID SOFTWARE Invalid software version on pCone antenna, please connect Base Station to Internet.
COMPONENTS OVERVIEW CELL BASE STATION LED’S PCONE BASE STATION WIFI LED ON / OFF BUTTON PCONE ANTENNA Long press for ON, and long press for OFF. For communication with Cells. SENSOR CONNECTORS EXTRA ROD Connectors to the t-shirt sensors, clip into the pocket of the t-shirt. For extending the height of pCone antenna, for better signal reception. 14 OFF SOLID GREEN SOLID RED WIFI IS OFF Base Station WiFi is OFF. You cannot connect with the iPad app to the Base Station.
BASE STATION LED’S COMPONENTS OVERVIEW CENTRAL WEB SYSTEM (CWS) CONNECTION LED T-SHIRT OFF SOLID GREEN BLINKING RED NO CONNECTION No connection to CWS, you cannot synchronize data with web servers. READY TO SYNC Connection with CWS established, system is ready to synchronize data with servers. CONNECTION ERROR Limited Internet connection, CWS unreachable. Try to connect to a different Internet source, and try again. Please contact Customer Support if this persists. CELL POCKET Pocket for a Cell.
COMPONENTS OVERVIEW BASE STATION LED’S T-SHIRT BASE STATION BATTERY LED Centimeters SENSOR CONNECTORS 80 85 90 95 100 105 110 X-Small Best way to know what size to put on a player is to measure the circumference of his torso under his pectoral muscles. Small Medium Large X-Large If you do not have access to that measurement you can also estimate the shirt fit using height and weight. Consult the sizing chart.
BASE STATION LED’S COMPONENTS OVERVIEW POWER BUTTON LED T-SHIRT SHIRT ASSIGNMENT A specific Techfit elite smart shirt can be assigned to a player or a different shirt can be used in each session. OFF BLINKING GREEN BLINKING YELLOW 3x BLINKS RED SYSTEM IS NOT STARTED To enable power, put the hard Switch to position “I”, and short press Power Button. BOOTING UP Base Station prepares the system to operate. SHUTTING DOWN Base Station is closing the system. ONGOING PROCESS Rejected shutdown.
CONNECTING COMPONENTS STARTING NEW SESSION INSERT CELL INTO T-SHIRT BASE STATION STEPS STEP 1 STEP 2 STEP 3 STEP 4 Connect all components as on the “Connecting Components” tutorial. Set the Hard Switch Button on bottom of Base Station to position “ I “ Short press “Power Button” on the Base Station Wait until WiFi LED is Solid Green. INSERT CELL INTO POCKET Insert Cell into pocket on the back of the t-shirt. CLICK THE BUTTONS Close the Cell in the pocket by pressing the pins.
CONNECTING COMPONENTS ASSEMBLING PCONE ANTENNA AND CONNECTING TO BASE STATION RED DOT TO RED DOT SCREW THE LID Connect pieces in place of dots (antenna on top). Put the lid down and turn it till you feel resistance. CONNECTING COMPONENTS INSERT CELL INTO CHARGER PINS TO GAPS Put the Cell into Charger, so that the pins on Cells fit to gaps on Cells Charger. Press the Cell into Cell Charger until you feel the Click. CONNECTION INDICATOR If Cell is properly connected, the light should appear.
CONNECTING COMPONENTS CONNECTING COMPONENTS CONNECTING CELL CHARGERS TOGETHER CONNECTING CHARGERS TO BASE STATION POWER SOURCE SYNCING DATA Connect OUT slot with IN slot in the second Charger, using the provided cable. For sharing power. Connect BASE slot in Cells Charger with the USB slot on Base Station with the provided cable. DATA TRANSFER Connect CHARGER slot with BASE slot in the second Charger, using the provided cable. Serialize USB connection.
Specifications Base Station Power Input 19Vdc (+20%, -15%) 5A max Charger Player_Cell Input 19Vdc (+20%, -15%) 5A max Input 5Vdc(+/- 5%) 0.5A max 7.2V 8.4Ah 126Wh Lithium Ion Rechargeable Battery 3.7Vdc 0.8Ah 3.0Wh Lithium Ion Rechargeable Battery RF Protocol IEEE 802.15.4 IEEE 802.15.4 Frequency (MHz) 2400 2400 Technology ZigBee® ZigBee® Wireless IEEE 802.11 a / b / g / n Bands Dual Band 2.