Note: The Cali channel may only be programmed in 20 channel mode, 27 (10 ‘Scanning ‘SCANSION Button and DIN SCAN Button ] The following buttons have special-functions during scanning .
7; 0 Information @ Post dither the * MR JET button of G/VEOAN button to cancel scanning, The frequency displayed as button is depressed bodices the operating frequency, * Ba sure that tre Maharashtra Is in the dial-frequency mode before stirring the scan, especially right afire the memory mode is usd.
(2) WEST Sean @ Operation 1. This function slows you to sear the specified memory a) Set the Transceiver fo the dial frequency mode, Press frequencies only. the SCANDIUM button while pressing the Function button (5) Setting thé memory address number for BS.M scan. “9 will be indicated above “NY on the display end the a) Press tho * MR /Contribution for the memory mode. Transceiver is now ready fur MSM scan. 19} Display the desired address nimbler either with numeral b} Press the CAMBODIAN button.
[11 |switching the Transit Power To BIPLANE Button] This lg to switch the transmit power, Thais power levels are available for the HH Transceiver. Select high, mod die or fow prows depending on Your purpose. High power {MH Middle power (M is displayed). Low power {Lis displayed). (Procedure) a) Press the BP PL bunion to switch transmit power.
@ Dual-watch on the disk-frequency and a memory frequency. {or call frequency) &) Recall a memory frequency. you wish to use in the dusk-watch, b} Press the DOUALA button while pressing the function bunions. A word "DUAL" will appear on the display to indicate the dual-water Operation, ©} The display will alternately indicate the dial-frequency and a played displayable for sediment memory frequency, 3 second app 0.
a [13 [MHz Notary Ste LTA bh MHz the “MENTOR key to set the status in VFO mode, ib} Press the "A/MHz" the enable the MHz Rotary step function «} Rotate tha rotary channel to increase of decrease the operating frequency in MHz increment, df} Press "MHZ" or "IMMINENT” to returns to MHz VFO mode. [Changing the Frequency Step ! TT 13/STEP Button | You can set the Transceivers step rate to KHz, kHz, kHz, kHz or Bike.
[1 15 [Battery wave Function 7 [SAVE Button] This function allows you fo reduce the current drain to 1/3 during receiver standby. The receiver will bio activated ones every single second. a} Press the SAVE button while pressing the Function button ACE will appear on the display to indicate that the battery-save function is enabled. 1) Press the S/SAVE button again while pressing the Function button to release the battery saver. MOTE: The battery saver is disabled during duality operation ang scanning.
19 Tone Squelch Control TT TI4ICTCSS Button] Tone squelch.operation is available when an optional tone squelch unit CTS145 is installed. NOTE: {1} Communication between stations capable of tone squelch operation or having different tone frequencies LC is unavailable.
ee (Procedure wu) Pres the O/SET button while passing the Function bunion ACW will appear on the display io indicate the set mode. b) Press the O/BET button. o} The buzzer is muted and pressing a button will not generate any sounds. d) Press the O/SET bunion while pressing the Function button and then press the B/SET button again by itself to enable tha blazer, NOTE: {1} The display does not indicate whether the buzzer is ted or nat.
@) fates Power OF Ary Byblos-Powdr UF feature Is built in to conserve power, ‘When: {ie Transceiver is left unused with the power switch EE bi for Je unites, the Transceiver will generate Heaping Aldrin Alter the alarm, the Transceiver will automatically extinguish the most of the display and reduce the power consumption to approximately Sma, rude) a} Prosy the BEST button while pressing the Function button AMT wilt appear on the display to Indicate the set mods.