Installation Instructions

ManualsBrandsAdemco ManualsElectronicsWireless Heat/Smoke Detector

PROSiXSMOKEV

Wireless Smoke/Heat Detector

This is a multi-criteria wireless smoke

detector which employs advanced levels

of detection and discrimination to

reduce common cooking nuisance

alarms and faster to different types of

fire conditions. It is intended for use

with Controls that support PROSiX™

series devices.

To remove the mounting bracket, turn

the top of the detector 15 degrees

counterclockwise and separate the

mounting bracket and top cover.

PROSiXSMOKEV

Open

Enrollment

Enroll the device using AlarmNet 360. When prompted, activate the

device by pulling the battery tab or, if already powered, press the

Test button to enroll. It will enroll into 2 zones: smoke detection into

one zone and heat detection into a second zone.

If the detector is not successfully enrolled during the enrollment

period, the LED turns off and the device powers down. Activate the

tamper or press the Test Button to restart the enrollment process.

NOTES: Enrollment time varies depending on the signal strength

between the device and the Control. Once enrolled in a system, the

detector cannot be used with another Control until it is removed from

the current Control. See the Control’s instructions for details.

Enroll

Program

Consult the Control’s instructions to program the device in the system. This detector reports the following signals to the Control:

• Smoke and Heat detection

- Smoke Alarm when smoke is detected

- Heat Alarm when temperature of 135° F (57° C) or greater

- Rate-of-Rise Alarm when temperature is >104° F (40° C) @ 15° F/minute (8.33° C/minute).

• Maintenance: Contaminated chamber that requires cleaning.

• End-of-Life

• Base Tamper: It will send a tamper signal to the control when the smoke head is removed from its base.

• Supervision: 200 second check-in compatible.

• Signal and battery Strength: Signal and battery strength information are sent with every communication to the panel.

NOTE: If programmed in the Control to operate in One-Go-All-Go mode, all smoke detectors programmed as One-Go-All-Go in the

system will sound on alarm.

Tamper

When the detector is removed from its base, it will send a tamper signal to the Control. OPTIONAL: The detector can be made

tamper-proof to prevent unauthorized removal from its base. Break off the small pillar on the base as shown. This will cause the

detector to latch to the base. From this point on, to remove the detector from its base, you must use a small screwdriver to release

the catch (push the catch towards the base) and twist the detector counter-clockwise. A screw can be added to prevent removal

from the base.

Summary of content (4 pages)

PAGE 1
PROSiXSMOKEV Wireless Smoke/Heat Detector Installation Instructions This is a multi-criteria wireless smoke detector which employs advanced levels of detection and discrimination to reduce common cooking nuisance alarms and faster to different types of fire conditions. It is intended for use with Controls that support PROSiX™ series devices. To remove the mounting bracket, turn the top of the detector 15 degrees counterclockwise and separate the mounting bracket and top cover.
PAGE 2
Mount Refer to the Smoke Detector System Application Guide (P/N SPAG9101) and the Limitations of Fire Alarm Systems (P/N 80015144) for detailed information on detector spacing, placement zoning and special applications. Copies of this document are available on https://mywebtech.honeywellhome.com/. NOTE: Before mounting the detector permanently, conduct a Walk test (see control’s instructions) to verify adequate signal strength and adjust the device location and orientation as necessary.
PAGE 3
LEDs and Sounder The PROSIXSMOKEV has one green LED and a separate bi-color (red and yellow) LED with an 85dB sounder. Refer to the following table below for operation of these features.
PAGE 4
Battery Replacement • • Twist the front cover counterclockwise 15 degrees and separate it from the mounting bracket. Remove both batteries and wait 10 seconds, then insert two new recommended batteries: - Panasonic CR123A NOTE: Do not mix old and new batteries, battery types or manufacturers. • Reattach to the detector to the mounting plate. Replace Batteries BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212° F (100° C) or incinerate.