User's Guide

ManualsBrandsAdemco ManualsElectronicsGRIP Defender Panel (ADT2X16AIO-2)

Ê800-243440Š

800-24344 4/18 Rev A Part 1

SYSTEM LED FUNCTIONS

LED Status Meaning

POWER Green – Steady AC Connected/Battery Charged

Red – Blinking Low Battery

Off No AC Power

STATUS Green – Steady System is Ready to Arm

Red – Steady System Armed

Red – Flashing Alarm or Alarm Memory

Red – Flashing

Alternately with

TROUBLE LED

(Flashing Amber)

System is in Programming Mode

Off System is Not Ready to Am

TROUBLE Amber – Steady System Trouble

Amber Flashing Device Trouble

Amber – Flashing

Alternately with

STATUS LED

(Flashing Red)

System is in Programming Mode

Off Normal System Status (No

Troubles Present)

TESTING THE SYSTEM

Using the Test mode allows each detection point to be checked for proper

operation. Testing should be conducted weekly to ensure proper

operation.

• The keypad sounds a single beep about every 60 seconds as a

reminder that the system is in the Test mode.

• Alarm messages are not sent to Central Station when Test mode is on.

If a problem is experienced with any detection point (no confirming sounds,

no display), call for service immediately.

Disarm the system and close all protected windows, doors, etc. The

READY indicator light should come on if all zones are intact

Enter 4-digit Master code +

(walk)

3. Listen. The external sounder should sound for about 1 second then

turn off. If the sounder does not sound, CALL FOR SERVICE. The

“Test in Progress” display appears only on the keypad that started

the test.

4. Fault zones. Open each protected door and window in turn and listen

for three beeps from the keypad. Each faulted detection point should

appear on the display. The display clears when the door or window is

closed.

5. Walk in front of any interior motion detectors (if used) and listen for

three beeps. Each detector should appear on the display when it is

activated. The display clears when no motion is detected. Note that if

wireless motion detectors

are used, there is a 3-minute delay

between activations to conserve battery life.

Test all smoke detectors, following the manufacturer's instructions.

When all detection points have been c

hecked and are intact

(closed), there should be no zone numbers displayed.

Exit test mode 4-digit code +

COMMUNICATION TEST

Perform a Communication Test to verify the communication paths to

the Central Station are working properly.

Enter 4-digit Master code +

SHUTTING DOWN/REBOOTING THE SYSTEM

Hard Reboot

To avoid corrupting the control’s memory, before removing power from

the system perform the following:

Disarm

the system

Enter 4-digit Master code +

Wait until all of the LEDs are blank before removing power

Soft Reboot

Perform the following, if instructed by an ADT Service Representative.

Enter 4-digit Master code +

TROUBLE CONDITIONS

The word CHECK on the keypad's display, accompanied by a

"beeping" at the keypad, indicates a trouble condition in the system at

the displayed zone number sensor and requires your attention.

Determine if the zone(s) displayed are intact and make them so if they

are not. If the display persists, CALL FOR SERVICE.

To silence the beeping for these conditions, press any key.

Typical Trouble conditions include the following:

Trouble Message Meaning

COMM. FAILURE

(or FC)

A failure has occurred in the telephone

communication portion of your system.

SYSTEM LO BAT

(or BAT with no zone No.)

Low system battery condition exists.

LO BAT+ zone descriptor

(or BAT with zone No.)

Low battery condition in the wireless

transmitter. Either replace the battery

yourself, or CALL FOR SERVICE.

Rcvr Jam (or CHECK 90) RF interference in wireless system

which may

impede reception from wireless sensors.

ALARM 1xx (or 91)

FAULT 1xx

CHECK 1xx

A communication problem between the

control and a connected device (e.g., RF

receiver, zone expander) where the “xx”

indicates the device address.

MODEM COMM (or CC) Indicates that the control is on-line with the

Central Monitoring Station's remote

computer.

AC LOSS (or NO AC) The system is operating on battery power

only due to an AC power failure.

If only some lights are out on the premises,

check circuit breakers and fuses and reset or

replace as needed.

TELCO FAULT (or CHECK 94)

The telephone line has a problem.

Busy-Standby (or dI) If this message remains displayed for more

than 1 minute, system is disabled. CALL

FOR SERVICE.

NOTES

SERVICING INFORMATION

Your local ADT Installer is the person best qualified to service your

alarm system. Arranging some kind of regular service program with

him is advisable.

Name:

Address:

Phone:

ADT Se c ur i t y S er vice s

15 0 1 Y a mat o R o ad

Boc a Ra ton , F L 3 3 431

ADT

ADT2X1

6AIO

SERIES

SECURITY SYSTEMS

Quick Guide to User Functions

User Guide Available Online: This Quick Guide describes the most frequently used features and functions of your system. For

full details of all user functions, please see the system’s User Guide located online at: https://www.adt.com/help/faq/system-

user-guides (see ADT ADT2X16AIO Series Security System User Guide P/N 800-24342 or higher). The full version User

Guide is also available from your installer upon request.

Congratulations on your ownership of an ADT Security System. This system provides:

• Three forms of detection: burglary, fire and emergency (see your installer for which forms of detection are installed)

• At least one keypad which provides control of system and displays system status

• Various sensors for perimeter and interior burglary detection

• Optional smoke or combustion detectors designed to provide early warning in case of fire.

Your system may also be programmed to automatically send alarm and status messages to a Central Monitoring Station.

SYSTEM BASICS

The following is a list of some of the most common features and

functions of your system:

• Several modes of burglary detection: Stay, Night-Stay, Away,

Instant, Maximum.

• Bypass feature lets you bypass selected zones while leaving the

rest of the system armed.

• Chime mode alerts you to the opening of protected doors and

windows while the system is disarmed.

• Fire and carbon monoxide detection are always active (if installed);

an alarm sounds if a fire or carbon monoxide condition is detected.

• Fire, Police and Personal Panic keys (if programmed) let you

manually initiate fire and personal alarms using the keypad.

• 4-digit security codes are used in conjunction with keypad

commands to perform system functions.

• Each user can be assigned a different security code, each with

different authority levels.

• The system sensors have been assigned to various “zones,” which

are specific areas of detection (e.g., front door, kitchen window, etc.).

• Zone numbers (points of detection) are displayed at the keypad

when an alarm or trouble condition occurs.

• Partitions provide independent areas of detection, with each

partition containing a group of zones that can be armed and

disarmed without affecting other zones or users.

ENTRY/EXIT DELAYS

• Entry Delays give you time to disarm the system when you enter

through the designated entrance door.

• You must disarm the system before the entry delay period ends, or

an alarm will occur (keypad beeps during the entry delay period,

reminding you to disarm the system).

• Exit delay gives you time after arming the system to leave through

the designated exit door(s) without setting off an alarm. If

programmed, a slow beeping will sound during the exit delay period

until the last 10 seconds, which then changes to fast beeping

(alerting you to the end of exit delay). If you cannot leave within this

delay time period, you should stop, disarm the system, and start

over to avoid a false alarm.

•

••

• See your installer for your delay times. See the full User Guide for

details on Exit Error alarms.

NOTES ON BURGLARY DETECTION

• The system must be armed before the burglary detection can

sense intrusions.

• To arm your system, enter your security code followed by the

desired arming key.

• To disarm the system, enter your security code then press

the OFF key.

• When an alarm occurs, the keypad sounds and displays the

zone(s) causing the alarm. The external sounder may also

sound.

• If your system is connected to a Central Monitoring Station,

an alarm message is also sent (delayed 30 seconds by

default to reduce false alarms).

• To stop the alarm sounding, simply disarm the system.

• Memory of Alarm: When an alarm condition occurs, the

keypad displays the number(s) of the zone(s) that caused the

problem, and displays the type of alarm. Clear the Memory of

Alarm display by entering another “off” sequence.

IMPORTANT: If you return to the premises and

the main burglary sounder is on, or the keypad

beeps rapidly upon entering the premises, it

indicates that an alarm has occurred during your

absence and an intruder may still be on the

premises. LEAVE IMMEDIATELY and CONTACT

THE POLICE from a nearby safe location.

NOTES ON FIRE AND CO DETECTION

• Your fire alarm system (if installed) is on 24 hours a day,

for continuous detection. In the event of an emergency,

the smoke and heat detectors sound their alarms,

triggering a loud, interrupted pulsed sound from the

Keypad(s) and any external sounders.

• You can silence the alarm at any time by pressing the OFF

key (the security code is not needed to silence fire alarms).

• Carbon monoxide (CO) detectors, if installed, provide

continuous detection. If a high level of carbon monoxide is

detected, an interrupted pulsed alarm sound occurs at the

keypads and the detector(s). Immediately move to a spot

where fresh air is available, preferably outdoors. From a safe

area, call your security service provider for further

instructions. To silence the keypad sounding, press the OFF

key. To silence the detector, see its instructions.

Summary of content (2 pages)

PAGE 1
SYSTEM LED FUNCTIONS LED POWER STATUS TROUBLE TROUBLE CONDITIONS Status Meaning Green – Steady Red – Blinking Off Green – Steady Red – Steady Red – Flashing Red – Flashing Alternately with TROUBLE LED (Flashing Amber) Off Amber – Steady Amber Flashing Amber – Flashing Alternately with STATUS LED (Flashing Red) Off AC Connected/Battery Charged Low Battery No AC Power System is Ready to Arm System Armed Alarm or Alarm Memory System is in Programming Mode System is Not Ready to Am System Trouble Device
PAGE 2
ARMING THE SYSTEM, CHIME MODE, and CONTROLLING DEVICES CHECKING OPEN ZONES PANIC KEYS Before arming, close all perimeter doors and windows and make sure the Ready to Arm message is shown. After arming, leave the premises through an entry/exit door during the exit delay period and be sure the door is reclosed to avoid causing an alarm.