Install Guide

ManualsBrandsAdemco ManualsElectronicsAll-In-One Wireless Control Panel

PROA7PLUS / PROA7 Security System

Installation and Setup Guide

This Quick Installation Guide provides the basic steps to quickly and easily install the

Burglar and Fire Alarm Control Panel, using the built-in programming defaults. The

control is designed to be placed on a desk/table top with the optional stand attached or

mounted to a wall using the wall mount.

STEP 1 - Installing the Rechargeable Backup Battery and

Power Connector

1. Remove the Control’s left and right side covers.

2. Install the PROWIFIZW (Wi-Fi

and Z-Wave

), PROLTE-Series (LTE)

Communications and/or PROTAKEOV Wireless Converter modules (if required).

3. Insert the Battery Pack into the case.

4. Connect the battery connector to the receptacle on the PC board.

5a. Connect the power cable to the GND and +9V terminals on the wall mount and to

the + and – terminals on the Power Supply. Refer to Table 1 for wire gauge and

length. Do not apply power at this time. OR

5b Connect the power supply connector to the receptacle on the desk mount. Do

not apply power at this time.

NOTE: If using the optional wall mount configuration, skip to the wall mounting

procedure. If using the PROA7DM Desk Mount refer to the Installation Guide

P/N 800-25157.

Optional PROWIFIZW, PROLTE-Series and PROTAKEOV Communications Module

Note: Refer to the Specific Module Installation section in the online Installation &

Reference Guide for installation instructions.

PROLTE-SERIES

MODULE

COVER

POWER

SUPPLY

RECEPTACLE

DETAIL A

MACHINE

SCREW

PROTAKEOV

MODULE

QS-148-V0

2-CELL

BATTERY PACK

(P/N 300-11186)

3-CELL

BATTERY PACK

(300-10186)

BATTERY

CONNECTOR

EXT INT

PROWIFIZW

MODULE

SCREW

Table 1 – Wiring Guide

Maximum distance between

power supply and control

Wire Gauge

(AWG)

Note: Use UL-listed limited energy

cable

Up to 25 feet (7.62m) # 22

Up to 45 feet (13.72m) # 20

Up to 70 feet (21.34m) # 18

Up to 110 feet (33.53m) # 16

Mounting the Base to a Wall (Optional)

For wall mounting, perform the following:

1. Secure the Mounting Plate to the wall with 4 screws.

2. Install the Tamper Screw as shown (if required).

3. Secure the Control to the Mounting Plate by aligning the slots on the wall mount

and sliding the unit up until tabs on the wall mount are engaged. Then push it

toward the wall until to lock it in place.

4. Secure the Control with the set screw.

QS-056-V0

WALL

MOUNTING

PLATE

TAMPER

SCREW

(IF REQ’D)

MOUNTING

SCREWS

(4-TYPICAL)

SET

SCREW

PROA7PLUS

SNAP

INTO

PLACE

ENGAGE

TOP CLEATS

STEP 2 - Setting up the Communication Links

Note: Do not connect to a receptacle controlled by a switch.

1. Plug the power supply into a 24-hour, 110VAC unswitched outlet. Upon power-

up, the “Please Standby!” will be displayed on the home screen.

2. Settings → Wi-Fi → Master User Code → Wi-Fi Networks OR Add networks

Manually OR WPS → Enter required information OR follow prompts → Save

STEP 3 - Registration Programming and Testing

Registration, Programming and Testing is conducted through AlarmNet 360™. On a

laptop, PC or Smart Device, go to: www.alarmnet360.com or the AlarmNet360 App.

IMPORTANT: Once the programming procedure has started and the unit is

powered up, do not remove power, disconnect the battery, or open the case.

Disconnecting power or activating the tamper switch can cause unpredictable

programming results.

Testing the System

The following test modes are available:

• Test Sensors (Walk Test)

• Test Communicator

Enter Test mode (Walk Test)

1. Select Test and enter the Master User Code.

2. Select System Tests.

3. Select Test Sensors. The system enters Walk Test mode. Follow the prompts.

4. Open each protected door and listen for three beeps from the keypad, followed

by the zone’s Voice Descriptor. Identification of each faulted protection point,

battery and signal strength appears on the display.

5. Walk in front of the motion sensor and listen for three beeps and the zone’s voice

descriptor.

6. Press each key on the keyfob to confirm it performs its assigned function.

7. When testing is complete, select End Test and follow the prompts.

8. Select the small

icon to return to the home screen.

Shutting Down the System

To avoid corrupting the control’s memory, before removing power from the system:

1. Disarm the system.

2. Wait 30 seconds.

4. Unplug the power supply.

5. Disconnect the battery.

Features and Capacities

Feature

Details

PROA7PLUS

PROA7

Partitions 4

• •

Maximum

Devices

• 250 Intrusion/Fire Zones

- 127 SiX Series devices

(sensors, keyfobs, keypads)

- 250 5800 series devices

(requires PROTAKEOV

module)*

• •

• 32 SiX Series Keyfobs

• •

• 8 SiX Series Keypads/

Touchscreens

• •

• Built-in Camera

•

---

Z-Wave Supports up to 78 Z-Wave devices

with the following maximums:

Light Modules .......................... 60

Garage Doors ............................ 6

Door Locks:............................... 6

Z-Wave Thermostats*: ............... 6

Wi-Fi Thermostats*: ................... 4

* Combination Z-Wave & Wi-Fi

thermostats maximum

................

• •

Bluetooth Smartphone disarming via Bluetooth

•

---

Wiselink Wiselink compatibility with

PROINDMV and PROOUTMV

Motion Viewers

•

---

Security

Codes

96 User Codes

(Includes Master User #1)

• •

Event Log 4,000 events

• •

* The PROTAKEOV module supports communication with certain previously installed wireless

sensors and modules. Refer to PROTAKEOV Compatibility chart (p/n R800-26221A or later) for

a list of tested and approved vendor wireless devices.

Specifications

Dimensions: 7.875” W x 5.75” H x 1.0” D

Voltage Input: P/N 300-10260 – 9VDC, 2.5A

P/N 300-10260-CAN (Canada) – 9VDC, 2.5A

24-Hour Backup Battery: P/N 300-10186: Rechargeable Backup Battery: Lithium-

ion battery pack rated at 3.6/4.2V, 7500 mAH

P/N 300-11186: Rechargeable Backup Battery: Lithium-

ion battery pack rated at 3.6/4.2V, 5200 mAH

Contacting Technical Support

PLEASE, before you call Technical Support, be sure you:

READ THE INSTRUCTIONS!

• Determine that the power supply and/or backup battery are supplying proper voltages.

• Verify your programming information where applicable.

• Note the proper model number of this product, and the version level (if known) along

with any documentation that came with the product.

• Note your Honeywell Home customer number and/or company name.

Keeping this information handy will make it easier for us to serve you quickly and

effectively. For technical support please call 1-800-645-7492

This system must be checked by a qualified technician at least once every

three (3) years.

Summary of content (2 pages)

PAGE 1
PROA7PLUS / PROA7 Security System Installation and Setup Guide This Quick Installation Guide provides the basic steps to quickly and easily install the Burglar and Fire Alarm Control Panel, using the built-in programming defaults. The control is designed to be placed on a desk/table top with the optional stand attached or mounted to a wall using the wall mount. STEP 1 - Installing the Rechargeable Backup Battery and Power Connector 1. 2. Remove the Control’s left and right side covers.
PAGE 2
The Limitations of this Alarm System While this system is an advanced design security system, it does not offer guaranteed protection against burglary or fire or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example: • Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or disconnect an alarm warning device. • Intrusion detectors (e.g.