Installation & Operation Guide

wboxtech.com
FOR MORE INFORMATION,
CONTACT YOUR ADI SALES PERSON
Installation & Operation Guide
One and Two-channel RF Receiver
Main Features:
Pairing a New Transmitter to the Receiver/Code Learning:
1. Connect the two power supply wires, one to VDD and the other GND.
2. When the power is initiated, the LED will light for 1 second and the receiver is
ready for learning.
3. Adding New code into Channel 1: Press LEARN BUTTON once, the LED will light for 1
second, go off for 1 second and then light again. Press any button on the Transmitter;
if the code is learned successfully, the LED will blink; then release the button on the remote,
the LED will be OFF. If the remote cannot read the signal, the LED will light for 10 seconds
and finish its learning status.
4. Adding New code into Channel 2: Press LEARN BUTTON twice, the LED will light for 1
second, go off for 1 second and then light again. Press any button on the remote; if the code
is learned successfully, the LED will blink; then release the button on the remote, the LED will
be OFF. If the remote cannot read the signal, the LED will light for 10 seconds and finish its
learning status.
2-CH Receiver shown
LEARN BUTTON: for pairing
transmitter with receiver or to
remove the transmitter.
Press once: for CH1
Press twice: for CH2
WBox Part #s: 0E-1CHRFRCVR & 0E-2CHRFRCVR
• Five relay output programming functions; each channel can be independently programmed
to operate in a different function
• Compatibility: Rolling code and fixed code
• Operating Temperature: -14 to 140°F ( -25 to 60 °C )
• Capacity to learn up to 200 codes
• Power supply: 12-24 VDC / VAC
• Frequency: 315MHz
• Relay Contact Rating: Dry Form "C", 10amp. Max. per channel
wboxtech.com
FOR MORE INFORMATION,
CONTACT YOUR ADI SALES PERSON
Installation & Operation Guide
Deleting code from the receiver:
Programming Channel Relay Output Modes:
Deleting all codes: Press LEARN BUTTON for 8 seconds or until the LED lights, release
the button and the LED will go off, all codes will have been deleted.
Each channel can be independently programmed to operate in a different function.
1. Hold the PROGRAM BUTTON 1 or 2 for 3 or more seconds. The LED on the receiver will
flash number of times equal to the output mode that it is in. (for example, if it flashes 2 times,
it means we are set to Toggle mode).
2. To change a relay output mode, press the program button, each press moves to the next
mode in the sequence shown in table 1.
3. After select the mode, count the number of LED flashes times to verify the channel is set
to the correct mode.
4. To exit programming, hold the PROGRAM BUTTON 1 & 2 for 3 seconds or wait 15 seconds.
Table 1:
Press Program Button N times
Default
2
3
4
5
1
2
3
4
5
4-Sec Timed Mode, Auto. OFF
Toggle Mode
Latch Mode
Validity Mode
1 Second Timed Mode
Times of LED Flashing Output Mode
4-Second Timed Mode (default): When transmitter button is pressed, the relay will turn ON
for 4s, then auto. OFF
Toggle Mode: When the transmitter button is pressed once and released, the relay will turn
ON, then one needs to press the transmitter button again, for the relay to turns OFF.
Latch Mode: Press the transmitter button once, and the replay turns ON and stays ON.
The relay will remain ON regardless of whether a compatible transmitter button is pressed again
or not. To turn the relay OFF, press the LEARN BUTTON on the receiver once to reset.
Validity Mode: The relay is ON for as long as the transmitter buttons is pressed.
1-Second Timed Mode: When the transmitter button is pressed, the relay will turn ON for 1s
& then auto. OFF.
Repeat above steps for Channel 2. (If your receiver has 2 channels)
Notes
California Proposition 65 Warning: These products do not contain chemicals which are
known to the State of California to cause cancer and birth defects or other reproductive harm.
wboxtech.com
FOR MORE INFORMATION,
CONTACT YOUR ADI SALES PERSON
Installation & Operation Guide
Diagram of the receiver:
NO CM NC NO CM NC VDD GND ANT
P2 P1
CH2 CH1
LED
LEARN
CH2 relay CH1 relay
(if your receiver
has 2 channels)
+
-
Power input
PROGRAM BUTTONS:
P1 button for Channel 1 programming
P2 button for Channel 2 programming
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT
TO THE FOLLOWING TWO CONDITIONS:
(1). THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND
(2). THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE
THAT MAY CAUSE UNDESIRED OPERATION.
wboxtech.com
FOR MORE INFORMATION,
CONTACT YOUR ADI SALES PERSON
Installation & Operation Guide
FCC/IC COMPLIANCE STATEMENTS
Warranty
Notice: The changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no
change to the antenna or the device is permitted. Any change to the antenna or the device
could result in the device exceeding the RF exposure requirements and void user’s authority
to operate the device.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
One Year Warranty
This product is covered by a 1-year limited warranty from the date of its original purchase.
Fully compatible W Box transmitters offered with One or Two-channel RF Receivers
* 315 MHz, Rolling code
* Battery storage life - Min. 2 years
0E-2C2BPTRAN
0E-2C2BHTRAN
0E-4C4BHTRAN
2x3vdc coin CR2016 Li batteries
1x12vdc cylindrical Alkaline battery
1x12vdc cylindrical Alkaline battery
2-channel 2-Button Pendant Transmitter
2-channel 2-Button Handheld Transmitter
4-channel 4-Button Handheld Transmitter