TECHNICAL USER'S MANUAL FOR: MPC40/A/B/C MPC41 Nordstrasse 11/F CH- 4542 Luterbach Tel.: ++41 (0)32 681 58 00 Fax: ++41 (0)32 681 58 01 Email: support@digitallogic.com Homepage: http://www.digitallogic.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C REVISION HISTORY: MPC40/ BIOS A/B Vers. V0.3 V0.1 V0.3 V0.3 V0.3 V0.4 V0.4 V0.4 V0.4 V0.4 V0.4 MPC BIOS 41 Vers. V0.1 V0.1 V0.1 Doc. Version V0.1 V1.0 V1.1 08.2003 KUF 11.2003 KUF 11.2003 HAK V1.2 V1.2A V1.2B V1.2C V1.2D V1.2E V1.3 01.2004 KUF 05.2004 DAR 05.2004 DAR 06.2004 DAR 07.2004 DAR 08.2004 DAR 09.2004 DAR V2.0 V2.1 V2.2 V2.3 V2.4 V2.5 V0.2 V0.2 V0.2 V0.2 V0.1 V2.0 V2.1 V2.2 V2.3 V2.4 V2.5 V0.4 V0.4 V0.5 V0.5 V0.5 V0.5 V0.5 V0.5 V0.5 V0.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C COPYRIGHT 2008 BY DIGITAL-LOGIC AG No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, in any form or by any means, electronic, mechanical, optical, manual, or otherwise, without the prior written permission of DIGITAL-LOGIC AG. The software described herein, together with this document, are furnished under a license agreement and may be used or copied only in accordance with the terms of that agreement.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C Table of Contents 1 PREFACE .......................................................................................................... 7 1.1 Trademarks .......................................................................................................................... 7 1.2 Disclaimer............................................................................................................................. 7 1.3 Environmental Protection Statement ..
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 4.1.5 MPC41.......................................................................................................................... 36 4.1.6 Connectors on frontside ............................................................................................... 37 4.1.7 Indicator LED’s on the frontside .................................................................................. 37 4.1.8 Operating elements .............................................
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 6.1.5 IEEE1394 / FireWire..................................................................................................... 73 6.1.6 Framegrabber / Video IN.............................................................................................. 76 6.1.7 Int15 emulator driver for W2k/XP ................................................................................. 76 6.2 Linux ......................................................................
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 1 PREFACE This document is for integrators and programmers of systems based on the MICROSPACE-Computer family. It contains information on hardware requirements, interconnections, and details of how to program the system. The specifications given in this manual were correct at the time of printing; advances mean that some may have changed in the meantime. The information contained in this document is, to the best of our knowledge, entirely correct.
DIGITAL-LOGIC AG 1.6 MPC40/A/B/C, MPC41 Manual V1.4C Recycling Information All components within this products fulfills the requirements of RoHS. The product is soldered with a lead free process. 1.7 Technical Support 1. Contact your local Digital-Logic Technical Support in your country. 2. Use Internet Support Request form on http://support.digitallogic.
DIGITAL-LOGIC AG 1.9 MPC40/A/B/C, MPC41 Manual V1.4C Explanation of Symbols CE Conformity This symbol indicates that the product described in this manual is in compliance with all applied CE standards. Please refer also to the section “Applied Standards” in this manual. Caution, Electric Shock! This symbol and title warn of hazards due to electrical shocks (> 60V) when touching products or parts of them.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 1.10 Applicable Documents and Standards The following publications are used in conjunction with this manual. When any of the referenced specifications are superseded by an approved revision, that revision shall apply. All documents may be obtained from their respective organizations. Advanced Configuration and Power Interface Specification Revision 2.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 1.11 For Your Safety Your new Digital-Logic product was developed and tested carefully to provide all features necessary to ensure its compliance with electrical safety requirements. It was also designed for a long fault-free life. However, the life expectancy of your product can be drastically reduced by improper treatment during unpacking and installation.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 1.12.1 RoHS Compatible Product Design All DIGITAL-LOGIC standard products comply with RoHS legislation. Since July 1, 2006, there has been a strict adherence to the use of RoHS compliant electronic and mechanical components during the design-in phase of all DIGITAL-LOGIC standard products. 1.12.2 RoHS Compliant Production Process DIGITAL-LOGIC selects external suppliers that are capable of producing RoHS compliant devices.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 1.14 The Swiss Association for Quality and Management Systems The Swiss Association for Quality and Management Systems (SQS) provides certification and assessment services for all types of industries and services. SQS certificates are accepted worldwide thanks to accreditation by the Swiss Accreditation Service (SAS), active membership in the International Certification Network, IQNet, and co-operation contracts/agreements with accredited partners. www.sqs.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 1.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 1.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 1.16.
DIGITAL-LOGIC AG 2 MPC40/A/B/C, MPC41 Manual V1.4C INTRODUCTION Attention! If the red seal on the rear plate is damaged, meaning the system itself was opened, then the warranty is void. Expansions can only be made by the manufacturer at the factory – the expansions then carry their own 2 year warrenty. 2.1 System Overiew The MICROSPACE-PC40 is a miniaturized PC system incorporating the major elements of a PC/AT compatible computer.
DIGITAL-LOGIC AG 2.3 MPC40/A/B/C, MPC41 Manual V1.4C Differences between MPC40, MPC40A, MPC40B, MPC40C, MPC41 The product has different functions: Option LAN-Port A LAN-Port B LAN-Port C Mouse Keyboard 1xPS/2 Mouse Keyboard 2xPS/2 Svideo Input Svideo Output Framegrabber MPEG2+AC3 Encoder USB 2.0 x5 USB 2.0 x4 Firewire IEEE1394 x2 CD-Drive CD/DVD-Drive CD-RW/DVD-Drive PC-CARD TYPI/TYPII (2Slots) Line Output 5.
DIGITAL-LOGIC AG 2.4 MPC40/A/B/C, MPC41 Manual V1.4C Assembly Options The product has different assembly options. Ask the factory for the detailed information about the current available options and combination of options. MPC40: Option: Part.No . SM855-C300 (0.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C MPC40B: Option: Part.No Comments: . SM855-C300 (0.6GHz) 807356 D Replace SM855-738 (1.4GHz) SM855-C373 (1GHz) 807357 D Replace SM855-738 (1.4GHz) SM855-P755 (2GHz) 807359 U Replace SM855-738 (1.4GHz) Customized front- and 807330 See price list U back cover Wireless LAN 813087 U WLAN IntelPro2200 incl Antenna, Must be ordered with the MPC, Harddiskdrive 80GB 807365 U Replace standard HDD 2.5” 40GB by 80GB Harddiskdrive 20GB 807366 Replace standard HDD 2.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C MPC41: Option: Part.No Comments: . SM855-C300 (0.6GHz) 807356 D Replace SM855-738 (1.4GHz) SM855-C373 (1GHz) 807357 D Replace SM855-738 (1.4GHz) SM855-P755 (2GHz) 807359 U Replace SM855-738 (1.
DIGITAL-LOGIC AG 2.5 MPC40/A/B/C, MPC41 Manual V1.4C Functional Block Diagram The diagram provide additional information concerning board functionality. Pentium-M PMC DDRRAM SODIM M200 VRM CRT1 GMCH 855GME DVO SIL 164 DVI AC97 5.1 SOUND HD CD 6xUSB V2.
DIGITAL-LOGIC AG 2.6 MPC40/A/B/C, MPC41 Manual V1.4C Technical Specification CPU: MPC40 Compatibility: 1. Level Cache: 2. Level Cache: Socket: Clock Pentium4 Performance: FSB Powermanagement FPU: Chipset: Nordbridge Southbridge LAN Audio Firewire IEEE1394 Video Framegrabber/TV-Input Memory Main Memory Flash-BIOS Setup EEPROM Flash-VideoBIOS: Video RAM Video controller Specification Pentium-M 8086 – Pentium 16k data and 16k code 1024/2048kByte SmartCore855 1.0GHz up to 1.6GHz 2.4GHz up to 3.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C External Interface Videointerfaces TV-Interfaces USB V2.0 IEEE1394 LPT1: COM1: COM2: Keyboard: Mouse: Audio: Specification CRT1, DVI S-Video Input (only on MPCxx version) 4 channels (rear), 1 channel (front) Firewire 2 channels (only on MPCxx version) LPT1 RS232 (option: RS422/485) Internal (option: RS422/485) PS/2 PS/2 Stereo I/O Powersupply: Input: Protection: Spec. Nom.
DIGITAL-LOGIC AG EMI / EMC Tests MPC40/A/B/C, MPC41 Manual V1.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 2.
DIGITAL-LOGIC AG 3 MPC40/A/B/C, MPC41 Manual V1.4C SAFETY REGULATIONS The verification of the safety is followed to the guideline adapted from the US Army Communication and Electronics Command Supplement (119 version) 1 to AR385-16. This sign indicates an important information. This sign indicates an information that may injure the health. This sign indicates an information that may destroy the device. This sign indicates voltages above 28Volts. 3.
DIGITAL-LOGIC AG 3.5 MPC40/A/B/C, MPC41 Manual V1.4C Safety: Protection of the Output Currents The computer system limits the current of all peripheral supply outputs with fuses or with electronic currentlimiters. The following table shows the maximum available currents at each peripheral connector: USB: KB/MS: VGA: Firewire 3.6 Nominal max. current: 0.5 Amp. @ 5V 0.1 Amp. @ 5V 0.1 Amp. @ 5V 0.5 Amp. @ 12V Max.Current 1 Amp. with resistor limiter 0.2 Amp. with polyfuse 0.2 Amp. with polyfuse 2 Amp.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 3.10 Safety: Protection against Over Temperature The computer system integrates temperature sensitive components like: - Harddisk (max. 55°C) The CPU with a max. junction temperature of 105°C In the BIOS, the temperatur level of the thermal protection of the CPU may be selected and enabled. If enabaled, the systems will reduce the CPU-Clock automatically, if the temperature rises above the defined limit.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 3.15 Environmental Safety: Noise Emmission This computer system is a low noise system. The level is less than 35 dbA. 3.16 Environmental Safety: Hazardous Atmospheres The computer system must not be used in a hazardous atmosphere, because the system is not prevented from accidental ignition. Do never use the system in explosive gas or vapor, combustible dusts or ignitable fibers and flyings. 3.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 3.21 Safety: Operators Security It is important to protect yourself and your equipment before you perform any of the procedures outlined in this manual. When making changes to the configuration, power off the system and disconnect all power cords from their source. To avoid damage or injury, always power off the system and disconnect all power cords from their source before handling the equipment.
DIGITAL-LOGIC AG 4 MPC40/A/B/C, MPC41 Manual V1.4C FUNCTIONS 4.1 Operating elements on the frontside: 4.1.1 MPC40 4.1.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 4.1.3 MPC40B 4.1.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 4.1.
DIGITAL-LOGIC AG 4.1.6 MPC40/A/B/C, MPC41 Manual V1.4C Connectors on frontside (1) USB Connector (only with standard model) (2) IrDA Transmitter/Receiver (only with standard model) The MPCxxA version (red front) has no connectors or interfaces on the frontside. 4.1.
DIGITAL-LOGIC AG 4.2 MPC40/A/B/C, MPC41 Manual V1.4C Operating elements on the rearside: 4.2.1 MPC40 Connectors: KB/MS: LAN-Port A: S-VHS In: VGA: S-VHS-Out: DVI: Keyboard direct connectd For keyboard/mouse it is a Y-Cable needed With activity / link – LED for port A Video-Input Analog VGA channel 1 TV Output SVHS DVI-D WLAN USB2 USB3 Firewire A Firewire B LPT1 (Antenna for WLAN only if ordered as Option) 2.Connector USB 3.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 4.2.2 MPC40A Connectors: KB/MS: LAN-Port A: VGA: DVI: Keyboard direct connectd For keyboard/mouse it is a Y-Cable needed With activity / link – LED for port A Analog VGA channel 1 DVI-D WLAN USB2 USB3 LPT1 Antenna for WLAN only if ordered as Option) 2.Connector USB 3.Connector USB Lineprinter Interface COM1 DC-IN: USB4 USB5 LAN-Port B: LAN-Port C: Sound: Serial Interface RS232 Supply DC Input with remote on/off 4. Conenctor USB 5.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 4.2.3 MPC40B Connectors: KB/MS: LAN-Port A: S-VHS In: VGA: S-VHS-Out: DVI: Keyboard direct connectd For keyboard/mouse it is a Y-Cable needed With activity / link – LED for port A Video-Input Analog VGA channel 1 TV Output SVHS DVI-D WLAN USB2 USB3 Firewire A Firewire B LPT1 (Antenna for WLAN only if ordered as Option) 2.Connector USB 3.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 4.2.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 4.2.5 MPC41 Connectors: KB/MS: LAN-Port A: S-VHS In: VGA: S-VHS-Out: DVI: Keyboard direct connectd For keyboard/mouse it is a Y-Cable needed With activity / link – LED for port A Video-Input Analog VGA channel 1 TV Output SVHS DVI-D WLAN USB2 USB3 Firewire A Firewire B LPT1 (Antenna for WLAN only if ordered as Option) 2.Connector USB 3.
DIGITAL-LOGIC AG 4.3 MPC40/A/B/C, MPC41 Manual V1.4C Power Supply (1) AC-Adapter: 4.3.1 Power Supply Connector ION GND ION 2 +POWER 2 3 1 1 Male (Computer) Signaldefinition: + Power GND ION 3 +POWER Female (Cable) 10 – 28Volt Powersupply 0V or Ground of the powersupply Remote ON Input or IGNITION-Input , 8V – 28V level on this Input will switch ON the computersystem.
DIGITAL-LOGIC AG 4.4 4.4.1 MPC40/A/B/C, MPC41 Manual V1.4C DC-PowerInput specifications Nominal DC-PowerInput voltage The nominal DC-powerinput is within the range of: 10Volt to 28Volt. That means the device may be used in 12V or 24V battery supplies as used in boats, cars and trucks. The DC-input is protected with an internal fuse from overcurrent ! To prevent from high voltage spikes there are different voltage supressor diodes integrated.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 4.5 Power on modes (startup modes) 4.5.1 Automatically power on Modes: 1. Default startup mode: 2. Autostart: start from the “ ” button starts, when the main power is connected Note: Changing of the startup mode is possible only when the computer is powered (Standby mode), but the computer is not switched on. In “off” state of the computer the led “PRG” is flashing about 2 times per second, in “on” state this led is off.
DIGITAL-LOGIC AG 4.6 MPC40/A/B/C, MPC41 Manual V1.4C Harddisk 2.5” standard model The internal harddisk is mounted onto 4 shock absorbers. Each absober are gummi cylinders with 40 shores.
DIGITAL-LOGIC AG 4.8 MPC40/A/B/C, MPC41 Manual V1.4C Serial- and Parallel Interfaces 4.8.1 Serial – Interface: The serial channels are fully compatible with 16C550 UARTS. COM1 is the primary serial port, and is supported by the board's ROM-BIOS as the PC-DOS 'COM1' device. The secondary serial port is COM2; it is supported as the 'COM2' device. Standard: COM 1/2: 16C550: 2 x 16C550 with 16 Byte FIFO The serial ports are interafced with a RS232C transmitter/receiver.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 4.9 Controllers 4.9.1 INTEL Processor Pentium-M The Intel® Pentium® M processor is a high performance, low power mobile processor with several micro-architectural enhancements over existing Intel mobile processors.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 4.9.1.2 Deep Sleep State Deep Sleep state is a very low power state the processor can enter while maintaining context. Deep Sleep state is entered by asserting the DPSLP# pin while in the Sleep state. BCLK may be stopped during the Deep Sleep state for additional platform level power savings. BCLK stop/restart timings on Intel 855PM and Intel 855GM chipset-based platforms are as follows: Intel® Pentium® M Processor Datasheet 14 4.9.1.2.
DIGITAL-LOGIC AG 4.9.1.4.1 MPC40/A/B/C, MPC41 Manual V1.4C Low Power Features • No bus master arbiter disable required prior to transition and no processor cache flush necessary. • Improved Intel Thermal Monitor mode. — When the on-die thermal sensor indicates that the die temperature is too high, the processor can automatically perform a transition to a lower frequency/voltage specified in a software programmable MSR. — The processor waits for a fixed time period.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 4.10 INTEL 855GM: Grafic-Memory-Control Hub 4.10.1 Processor Host Interface The GMCH is optimized for the Intel Pentium M processor. Key features of the Intel Pentium M processor system bus (PSB) are: • Source synchronous double pumped address • Source synchronous quad pumped data • System bus interrupt delivery • Low voltage swing (Vtt = 1.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 4.10.2 Intel 855GM GMCH Internal Graphics The GMCH IGD provides a highly integrated graphics accelerator delivering high performance 2D, 3D, and video capabilities. With its interfaces to UMA using a DVMT configuration, an analog display, a LVDS port, and two digital display ports (e.g. flat panel), the GMCH can provide a complete graphics solution. The GMCH also provides 2D hardware acceleration for block transfers of data (BLTs).
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 4.11 IO Control Hub Intel-ICH4/ICH4M Features: PCI Bus Interface Supports PCI Revision 2.2 Specification at33 MHz 133 MB/sec maximum throughput Supports up to six master devices on PCI One PCI REQ/GNT pair can be given higher arbitration priority (intended for external 1394 host controller) Support for 44-bit addressing on PCI using DAC protocol Integrated LAN Controller WfM 2.0 and IEEE 802.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C Power Management Logic ACPI 2.0 compliant ACPI-defined power states (C1–C2, S3–S5 ) Supports Desktop S1 state (like C2 state, only STPCLK# active) ACPI power management timer PCI PME# support SMI# generation All registers readable/restorable for proper resume from 0V susp.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 4.11.
DIGITAL-LOGIC AG 4.11.2 MPC40/A/B/C, MPC41 Manual V1.4C Interrupt Controllers An 8259A compatible interrupt controller, within the chipset device, provides seven prioritized interrupt levels. Of these, several are normally associated with the board's onboard device interfaces and controllers, and several are available on the AT expansion bus.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 4.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C Attention! There is no picture after changing values in the menu "DISPLAY PROPERTIES -> Settings"or you started the system without a connected monitor: You have to press the following key combination to get a picture again: CTRL+ALT+ Fx Fx: F1 = VGA F2 or F3 = SVIDEO F4 = DVI We recommend to change the settings in this Intel garphic menu.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 4.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 4.14 Speedstep Performance Control The Pentium-M improved the Speedstep mechanism, in adding a third power scheme in addition to the lowpower and the full-performance modes. This new mode is called adaptive mode, and allows the frequency and voltage to switch according to the CPU activity. The CPU uses a low-power mode by default, but when its activity increases, it switches itself very quicky in full-performance mode.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 4.15 FIREWIRE IEEE1394 Description: The Texas Instruments TSB43AB22 device is an integrated 1394a-2000 OHCI PHY/link-layer controller (LLC) device that is fully compliant with the PCI Local Bus Specification, the PCI Bus Power Management Interface Specification, IEEE Std 1394-1995, IEEE Std 1394a-2000, and the 1394 Open Host Controller Interface Specification.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 4.16 USB V2.0 USB Host controller functional description: PIIX4 contains a USB Host Controller (HC). The Host Controller includes the root hub with two USB ports. This permits connection of two USB peripheral devices directly to PIIX4 without an external hub. If more devices are required, an external hub can be connected to either of the built-in ports. The USB’s PCI configuration registers are located in function 2, PCI configuration space.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 4.18 LCD PanelLink (DVI) Silicon Image’s Transition Minimized Differential Signaling is an electrical standard used to transmit digital data to a display device. The transition minimization is achieved by implementing an advanced encoding algorithm that converts 8 bits of data into a 10-bit transition minimized, DC balanced character.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 4.18.1 DVI-Integrated (DVI-I): Supports both analog and digital connections to the display. This 29-pin connector can carry single or duallink all-digital video/data signals on 24 pins and uses 5pins to carry analog video/data signals and ground. It is easily distinguishable by the plusshaped slot surrounded by four pins used to carry the analog connection.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 4.18.2 General Description: The SiI 160 transmitter uses PanelLink Digital technology to support displays ranging from VGA to UXGA resolutions (25-165 MHz). The SiI 160 transmitter supports up to true color panels (24 bit/pixel, 16.7M colors) in 1 or 2 pixels/clock mode, and also features an inter-pair skew tolerance up to 1 full input clock cycle. An advanced on-chip jitter filter is also added to extend tolerance to VGA clock jitter.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 4.19 IrDA- Option Since BIOS version V1.02, standard- IrDA can be accessed through the connector X7 (pin5/pin6). The IrDA-Interface is not assembeld on the Standard-Product. It is available as option. 4.19.1 IrDA-BIOS Settings I/O Device Configuration : Serial Port B : Mode : Base I/O Adress : Interrupt : Auto oder Enabled IRDA 2F8 IRQ 3 4.20 WLAN Option Internaly connected to the UBS channel 1 ! General Feature Compliance with IEEE802.
DIGITAL-LOGIC AG 5 MPC40/A/B/C, MPC41 Manual V1.4C OPERATING SYSTEMS COMPATIBILITY The CPU PENTIUM is fully compatible to other PC-standard CPUs. The Intel chipsets are also fully PCcompatible. No incompatibilities are known. 5.1 Microsoft Windows This system is fully compatible with Windows 2000 and Windows XP Professional / Home and XPe. We do not recomment to install older Windows OS as Windows 95/98/ME/NT4 because of the incomplete driver support from Intel. 5.2 Microsoft Windows CE 4.2 / 5.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 5.4 Realtime OS Must be tested carefully first. Many powermanagementfunction will control the latency time. Contact your realtime operating system manufacturer and ask for the support of the intel chipset 855GME.
DIGITAL-LOGIC AG 6 MPC40/A/B/C, MPC41 Manual V1.4C DRIVER INSTALLATION 6.1 Windows 2000 & XP On the MICROSPACE Application CD you will find all tools and drivers you will need to work with the card. If you are not sure about the topicality of the software, please visit our homepage at http://www.digitallogic.com to get the latest releases ! A correct installation of Windows is required for the following steps.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 6.1.2 VGA / CRT Driver: BSP CD 855: \DRIVERS\XP-W2k\VGA\General-VGA-Driver Doubleclick on setup.exe. Follow the instructions: Reboot the system after the installation. 6.1.3 LAN / Ethernet Driver: BSP CD 855: \DRIVERS\XP-W2k\LAN\General-LAN-Driver Doubleclick on setup.exe. Follow the instructions: or doubleclick autorun.exe and follow thw instructions: Press “Install Software” Reboot the system after the installation.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 6.1.4 AC97-SOUND Driver: BSP CD 855: \DRIVERS\XP-W2k\Audio\General-Audio-Driver Doubleclick on setup.exe Follow the instructions: Reboot the system after the installation.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 6.1.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C Driver location under Hardware manager 6.1.5.1 EEPROM Update utility An EEPROM is present on the design storing some important information about PCI configuration and a global unique ID that is required by all 1394 device to be fully compliant. The MSMW104+ EEPROM is already programmed with the right file to configure PCI registers specific to TI TSB43AB22 device.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 6.1.6 Framegrabber / Video IN 6.1.6.1 MPC40/A/B If Windows is asking for the Framegrabber/VideoIn/ Multimedia driver, you have to select the following path: Driver: BSP CD 855: \DRIVERS\XP-W2k\VideoIN\General_BT878-Driver You have to install this driver manually, there is no “setup.exe” Do not use the driver located in the MPC41 directory! 6.1.6.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 6.2 Linux 6.2.1 Video IN for MPC40C Kernel configuration: Device drivers I2C support I2C support Multimedia devices Video for Linux BT848 Video for Linux Important: The BT848 Video for LINUX option only appears when I2C support is selected. Compile the driver as a module as it needs to be parameterized. Load the module as: # modprobe bttv card=8 Note...
DIGITAL-LOGIC AG 7 MPC40/A/B/C, MPC41 Manual V1.4C SOFTWARE 7.1 Video Framegrabber 7.1.1 AMCap 878A for WINDOWS Location: \Drivers\MPC4x_x-MPCF40\VIDEO_IN AMCap from Microsoft-XP is a sample application which can preview and capture input from audio / video capture PC peripherals, including (but not limited to) 1394 conferencing cameras, DV camcorders, USB microphones and webcams, and TV tuner cards. AMCap is provided in the Windows DDK as a tool for testing Video Capture drivers and drivers.
DIGITAL-LOGIC AG 7.1.2 MPC40/A/B/C, MPC41 Manual V1.4C Video Framegrabber 878A for WINDOWS Digital-Logic AG Video Grabber for 878A of MPC40 Systems Location: \Software\VideoIn If you need other TV-Standard as PAL, than select the standard with the AMCap bevor Using this videograbber. Selects PAL/NTSC or SECAM Format in AMCap ! The VIDEOGRABBER program is intended for showing the simple use of video input.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C “Options”: Preview. Sets the display area to display an image stored in the frame buffer after capture. Overlay. Sets the display area to display the video-input signal from the hardware source (before capture). “Capture Video Sequence”: This lets you specify parameters for the capture session and the video sequence, including the video and audio format. There are the following options: Frame Rate. Sets the number of frames per second to capture.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 7.2 Windows Int15 Tool Please find the tool and the driver under: BSP CD 855: \TOOLS\General-Intel855Tools\DL-INT15_Tool on the product CD or in the download area of the support center. Note: Before you can use these tools, you have to install the Windows WDM driver first. See chapter 6.2.6 7.2.1 Int15 Windows Software - WinInt15.exe (Int15 function test tool) - T855.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 7.3 Speedstep Select: BSP CD 855: \TOOLS\General-Intel855Tools\SPEEDSTEPXP Doubleclick on “sswitchxp130.exe”.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 7.4 Identification Utility 7.4.1 Processor Frequency Utility Path: BSP CD 855: \TOOLS\General-Intel855Tools fidenu32.msi 7.4.2 Frequency Display Path: CD 855: \TOOLS\General-Intel855Tools FrequencyDisplay202.exe 7.4.3 Chipset Identification Utility Path: x CD 855: \TOOLS\General-Intel855Tools CHIPUTIL.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 7.5 Remote Control over COM Port 7.5.1 Requirements Serial Null-Modem cable (only RX and TX) Remote computer: Serial port address 3F8h Host computer: Serial port COM1 or COM2, OS (Windows or MSDOS), floppy image file with MSDOS 6.22 or FREEDOS (eg. freedos2img which is located on the product CD or in the download area). 7.5.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C Note… All remote features are supported only under FREEDOS or MSDOS 6.22. Note… When the remote floppy option is enabled, it’s impossible to use another floppy disk; even the USB floppy is not accessible. 7.5.5 Settings on host computer. Note… Remote console application must be loaded and connected before switch on (BIOS start) the remote computer. 7.5.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C Windows application Remote855.exe Please, start now the remote computer. Functions: R – enable this option is helpful, when remote application is working in directvideo mode without using BIOS Int10 functions. Every 0.5-1 second windows application will send a request to remote computer to refresh a screen on the host computer. Eg. If you want to use the “Volkov Commander VC” you have to enable this feature. Ctrl-Alt-Del simulation.
DIGITAL-LOGIC AG 8 MPC40/A/B/C, MPC41 Manual V1.4C DIMENSIONS 8.1 Front view 8.
DIGITAL-LOGIC AG 8.3 MPC40/A/B/C, MPC41 Manual V1.
DIGITAL-LOGIC AG 9 MPC40/A/B/C, MPC41 Manual V1.4C BIOS The BIOS-setup menu allows several adjustments of the system which must be implemented only by skilled personal. 9.1 BIOS-History MPC40/A/B MPC41 Until 01.01.2007: Version/ Release: 1.00 1.2 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.01 Date: Description Nov 03 Oct.03 Jan.04 Feb.04 Feb.04 Mar.04 Mar.
DIGITAL-LOGIC AG 3.04 Mar. 06 3.05 Nov. 06 MPC40/A/B/C, MPC41 Manual V1.4C - Fix for secondary IDE (was always Removable) Corrected detection of Celeron without SpeedStep and TM1 Added USB 2.0 Legacy Support Menu to select FullSpeed or HiSpeed Disabling of USB2.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 9.2 BIOS-History MPC40/A/ MPC41 Since 01.01.2007: Version/ Release: Date: 3.05 Nov. 06 3.09 July 07 Description - Added USB 2.0 Legacy Support Menu to select FullSpeed or HiSpeed Disabling of USB2.0 Support fixed PCI to ISA bridge ATTENTION: Please use the command line: Phlash16.exe bios.wph /mode=3 to download a core bios greater than V3.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 9.3 BIOS-History MPC40B/C Since 01.01.2007: Version/ Date: Release: 3.07 Jan.
DIGITAL-LOGIC AG 9.4 Version/ Release: 8.0 9.5 • MPC40/A/B/C, MPC41 Manual V1.4C PMPIC-BIOS-History Date: Description 25.6.03 Basic Version Remarks File Activate the BIOS setup After turning on the device, immediately press the key: F2 and the menu of the BIOS setup appears. 9.6 Phoenix BIOS function keys The special keys which are used in the Phoenix BIOS are: Action Call BIOS Change settings Navigation Save Terminate 9.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 9.9 Download CORE-BIOS Before downloading a BIOS, please check as follows: - Make a bootable diskette including the following files: - DELEP855.EXE - phlash16.exe* - core BIOS (SM855_xx_FLASHABL.ROM) Rename the SM855_xx_FLASHABL.ROM file to bios.wph * = see ATTENTION below IMPORTANT: Do not use boot disks created in a Windows operating system. If you do not have a MSDOS 6.22 disk available, you can download a boot disk from www.bootdisk.com .
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 9.10 Error Messages (Beep Codes) During the boot process the BIOS produces status messages in the shape of data onto Port 80H and acoustically by internal beeper in case the screen is not initialized. PHOENIX 1 1-2 2-2-3-1 1-3-4-1 1-3-4-3 1-3-1-1 1-3-1-3 1-2-2-3 1-2-3-1 1-2-3-3 1-3-3-1 1-4-2-1 1 x sort signal before booting (INT19H) Search for BIOS extensions. 1x long, 2x short signal by faulty checksum.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 9.11 BIOS Settings 9.11.1 Quick guide: 9.11.1.1 Sub Menu „Main Choice“ In this main overview the following changes can be carried out: Set Date/Time (see chart below) Turn on and off quick boot resp. diagnostic screen. • Language choice between german and english. Feature System time System date Options HH:MM:SS MM/DD/YYYY Description Set time Set of current date 9.11.1.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 9.11.1.3 I/O Device Configuration Feature Serial interface A: Seraial interface B: Options Disabled Enabled Auto OS Controlled Parallel Port: Disabled Enabled Auto OS Controlled Mode Output only Bi-directional Description “Disabled” turns off the ports. “Enabled” requires a manual base address and an IRQ. “Auto” configurates through PnP resources for the interface.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 9.11.1.4 Submenu „Security“ To use password security functions see following chart: Feature Setting of user password Feature Setting of supervisor password Password on boot Options Max. 7 alpanumeric figures Options Max. 7 alphanumeric figures Enabled Disabled Description Pressing the key summons the entering of a user password. Therewith certain settings are protected.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C This list is subject to a permanent update and extension. The right column contains a not final list of the devices supported by PHOENIX Possibly not all devices of the list are directly supported due to space problems. The service team of DigitalLogic is responsible for individual wishes of customers.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 9.11.2 Main 9.11.2.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 9.11.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 9.11.3.1 Advanced IO 9.11.3.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 9.11.3.3 Advanced Cache ATTENTION! If you change the red marked settings, the board will not start up anymore! Only with a external VGA board it is possible to access the bios setup to set the default values. 9.11.3.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 9.11.3.5 PCI/PNP ISA IRQ Exclusion 9.11.3.6 PCI/PNP ISA UMB Region Exclusion ATTENTION! If you change the red marked settings, the board will not start up anymore! Only with a external VGA board it is possible to access the bios setup to set the default values.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 9.11.3.7 PCI/PNP ISA DMA Exclusion 9.11.3.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 9.11.4 Intel 9.11.4.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 9.11.4.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 9.11.4.3 Intel Video ATTENTION! If you change the red marked settings, the board will not start up anymore! Only with a external VGA board it is possible to access the bios setup to set the default values. Exception: If you want to install a external VGA card on the PC104 or PC104+ BUS. 9.11.4.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 9.11.4.4.1 Intel ICH Integrated 9.11.4.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 9.11.4.6 Intel APM 9.11.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 9.11.6 Power 9.11.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C 9.11.
DIGITAL-LOGIC AG 10 MPC40/A/B/C, MPC41 Manual V1.
DIGITAL-LOGIC AG 11 MPC40/A/B/C, MPC41 Manual V1.4C INDEX F 1 16C550 UARTS 47 3 32Bit 63 FireWire FIREWIRE IEEE1394 Framegrabber Framegrabber / Video IN Framegrabber 878A Frequency Display Functions 73 62 78 76 79 83 34 8 8259A H 56 Harddisk 2.
DIGITAL-LOGIC AG MPC40/A/B/C, MPC41 Manual V1.4C Swiss Quality Q Q&A Questions and Answers 113 113 T Technical Specification Technical Support Trademarks R Realtime OS Recycling Information Remote Control Remote ON/OFF RoHS Commitment 12 69 8 84 45 11 25 8 7 U USB V2.
