Addonics T E C H N O L O G I E S Jupiter Combo Hard Drive For the following models: AJCHDIU, AJCHDIF, AJCHDIS AJCHDSAU, AJCHDSAF, AJCHDSAS User’s Guide Version 1.
FCC Warning Statement This equipment has been tested and found to comply with the limits for a class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications.
Contents FCC Warning ................................................................................... 1 Limited Warranty ............................................................................ 1 Contents............................................................................................ 2 Chapter 1 General Information ......................................................... 3 Features............................................................................
Chapter 1 General Information The Addonics Technologies Jupiter Combo Hard Drive is a portable 2.5” Hard Disk Drive kit. Features • • • • • • • • • • • Stylished and rugged black anodized aluminum housing Compact size and light weight Shock proof - up to 3 feet drop damage protection for the hard drive Easy hard drive installation Choice of standard or encryption drive enclosure The most versatile hard drive kit in the market Connect as an External Hard drive to any computer via USB2.
Chapter 2 Jumper Settings Inside the Jupiter Combo Hard Drive Case A. Settings when Jupiter ExDrive is used as an External Enclosure 1. If the Jupiter ExDrive will be used externally with the external AC adapter, the switch from the case must be switch to the right, labeled EXT to grab power from external power supply. Application: Jupiter ExDrive can be set to receive power EXT and be used with three types of USIB cables: USB2.0 USIB, Firewire USIB & SATA USIB 2.
FOR 2.5” SATA HARD DISK DRIVE J2 Pin Definition for USIB Interface Pin 3 - Pin 5 shorted Addonics Technologies – Jupiter Combo Hard Drive User’s Guide v1.
Chapter 3 Hardware Installation Guide FOR 2.5” IDE HARD DISK DRIVE top cover 2.5” hard drive shock absorbers IDE connector switch PCB bottom cover screw FOR 2.5” SATA HARD DISK DRIVE top cover 2.5” SATA hard drive shock absorbers SATA connector PCB switch bottom cover screw Addonics Technologies – Jupiter Combo Hard Drive User’s Guide v1.
Step 1 Separate the top from the bottom cover of the drive enclosure by loosening the screw as shown on the photo. Step 2 (IDE HDD) Align the male IDE connector on the 2.5” hard drive with the female IDE connector on the PCB. (SATA HDD) Align the SATA connector in the 2.5” hard drive with the SATA connector on the PCB. Push the hard drive till the connector pins on the har d drive is fully seated inside the connector on the PCB. Addonics Technologies – Jupiter Combo Hard Drive User’s Guide v1.
Step 3 Wrap the shock absorbers around the hard drive and PCB. Step 4 Turn over the PCB and secure the hard drive to the PCB with the mounting screws that come with the kit. Step 5 Mount the board to the bottom cover. Step 6 Put the top cover on by holding it in near vertical position and sliding the two metal clips inside the two small slots on the rear of the bottom cover. Addonics Technologies – Jupiter Combo Hard Drive User’s Guide v1.
Step 7 Lower the front of the top cover and making sure the two covers lined up properly. Tighten the small retaining screw on the front of the bottom cover to close the enclosure. Addonics Technologies – Jupiter Combo Hard Drive User’s Guide v1.
Jupiter Combo Hard Drive Note: Combo hard drive is the combination of Jupiter ExDrive kit and the IDE cartridge cradle. Allows a 2.5” Jupiter ExDrive to be used as an external hard drive and also be plug-in to a desktop computer internally. You may use an available 3.5” Floppy bay like the image shown below to install the Jupiter ExDrive cradle. If none is available you can mount one to a 5.25” bay with mounting brackets to fit the bay.
Jupiter ExDrive is used as an Internal Enclosure Power Socket 40 Pin IDE Connector MC-36 Pin Connector Note: Use the jumper settings on the next page for the above configuration Addonics Technologies – Jupiter Combo Hard Drive User’s Guide v1.
Configuration: Jupiter Cipher ExDrive enclosure is inside mobile rack. Mobile rack is connected to the IDE Controller on the mainboard with an IDE cable. FOR 2.5” IDE HARD DISK DRIVE A. Jupiter ExDrive is set to MASTER Hard Drive Brand Hitachi NEC Fujitsu Toshiba Seagate Hard Drive Setting Master J4 Jumper Setting Pin 1~6 Open J1 Jumper Setting Pin 1 – Pin 3 Short Pin 2 – Pin 4 Short B.
FOR 2.5” SATA HARD DISK DRIVE J2 Pin Definition for USIB Interface Pin 1 - Pin 3 shorted Pin 2 - Pin 4 shorted Since the Jupiter Mobile Rack will be use internally without external AC adapter, the switch from the case must be switch to the left, labeled INT to grab power from system. Addonics Technologies – Jupiter Combo Hard Drive User’s Guide v1.
Optional Hardware A. SATA Cartridge Cradle System 4-pin Molex power connector for PC power supply 2-pin connector on the PCB board SATA connector IDE to SATA converter 2-pin connector on the IDE to SATA converter board For Win98SE, Me, 2000 and XP Note: There are no drivers needed to use the Serial ATA cable as long as the drivers are installed for the Serial ATA Controller card/chip. It is plug and play.
Jumper Settings for Internal Cartridge Cradle System FOR 2.5” IDE HARD DISK DRIVE Jupiter ExDrive is set to MASTER Hard Drive Brand Hitachi NEC Fujitsu Toshiba Seagate Hard Drive Setting Master J4 Jumper Setting Pin 1~6 Open J1 Jumper Setting Pin 1 – Pin 3 Short Pin 2 – Pin 4 Short FOR 2.5” SATA HARD DISK DRIVE J2 Pin Definition for USIB Interface Pin 1 - Pin 3 shorted Pin 2 - Pin 4 shorted Addonics Technologies – Jupiter Combo Hard Drive User’s Guide v1.
Chapter 4 Attaching USIB interface cable USIB connector for use with the Addonics USIB interface cable External power input jack (for use as external hard drive) Addonics USIB interface cable Addonics Technologies – Jupiter Combo Hard Drive User’s Guide v1.
Chapter 5 5.1 USB2.0 USIB Cable (Model: AAUSBC-309) Note: USB Jupiter ExDrive is Plug and Play under Windows XP, 2000 and 98Me. There is no third party driver needed. • • Since USB 2.0 Hi-Speed is an evolution of the existing USB 1.1 specification, it is fully forward and backward compatible with current USB systems. If you do not have an USB2.0 port, you may install an optional USB2.0 adapter or controller Driver Installation for Win98 and Win98SE Downloading the USB2.
Driver Installation for Win98 and Win98SE 1. Make sure your computer is up and running. 2. Insert the USB2.0 USIB cable to the USB Port. 3. A "New Hardware Found" message shall pop up, click Next. 4. “What do you want Windows to do?” message opens. Select “Search for the best driver for your device,” click Next. 5. “Specify Location” message opens. Point to the location of C:\mass_storage_601where you unzip the files for the driver. Click Next. 6.
5.2 SATA USIB Cable (Model: AASAC-605) For Win98SE, Me, 2000 and XP Note: There no drivers needed to use the Serial ATA cable as long as the drivers are installed for the Serial ATA Controller card/chip. It is plug and play. Disk Management for Windows 98 Note: Refer to the SATARAID Management Utility Manual SATARAID Manual V1.30 (for non-RAID5 Controllers) found in the Addonics Technologies website Addonics Technologies – Jupiter Combo Hard Drive User’s Guide v1.
5.3 FIREWIRE USIB Cable (Model: AAFWC-406) Note: Firewire Jupiter ExDrive is Plug and Play under Windows XP, 2000 and 98Me. There is no third party driver needed. Driver Installation for Win98 and Win98SE After plugging in the cable some system might prompt you for Win98SE CD, in case you don’t have The Win98SE CD and the wizard prompt you for: NTMAP.SYS please type C:\WINDOWS\SYSTEM32\DRIVERS NTMAPHLP.PDR please type C:\WINDOWS\SYSTEM\IOSUBSYS Reboot your system. Disk Management for Window 98 1. 2. 3.
For Windows 2000 & XP Operating Systems How to use Disk Management To start Disk Management: 1. Log on as administrator or as a member of the Administrators group. 2. Click Start, click Run, type compmgmt.msc, and then click OK. In the console tree, click Disk Management. The Disk Management window appears. Your disks and volumes appear in a graphical view and list view. 3.
7. Confirm that the options that selected are correct, and then click Finish. The new partition or logical drive is created and appears in the appropriate basic disk in the Disk Management window. If you chose to format the volume in step 6, the format process now starts. How to format a basic volume To format a partition, logical drive or basic volume: 1. In the Disk Management window, right-click the partition or logical drive that you want to format (or reformat), and then click Format. 2.
Technical Support If you need assistance to get your unit functioning properly, please call Addonics Technical Support. Our technical staff will be happy to assist you, but they will need your help to do so. Calling the technical support staff without all the proper information can be both time consuming and frustrating. Here are some tips to help you out: (1) (2) (3) (4) MODEL NUMBER – Please have this number on hand. SYSTEM INFORMATION – Type of computer, peripherals, etc.
