User Manual

ManualsBrandsADC Telecommunications ManualsElectronicsDigivance SMR 20 Watt System

ADCP-75-159 • Issue 1 • August 2003 • Section 3: Host Unit Installation

Page 3-12

Figure 3-10. Configuring CAN Connections with Multiple Host Units

9 EMS COMPUTER CONNECTION

The service interface connection between the HU and the EMS computer is supported by a

single DB-9 female connector. The service connector provides an RS-232 DTE interface. A

three meter long straight-through RS-232 interface cable is available (accessory) for connecting

the EMS computer to the HU. Use the following procedure to install the service interface cable:

1. Connect one end of the service interface cable (accessory) to the SERVICE port as shown

in Figure 3-11.

2. Route the service interface cable to the EMS computer and connect the free end of the

cable to the computer’s RS-232 DCE port. Refer to the user manual provided with the

computer to locate and configure the specified port.

Figure 3-11. Service Interface Connection

HOST UNIT 1 HOST UNIT 2 HOST UNIT 3

NET IN NET OUT NET IN NET OUT NET IN NET OUT

16900-B

CONTROLLER AREA NETWORK

INTERFACE CABLES

TO NEXT HOST UNIT

(NOTE: LAST HOST HAS NO

CONNECTION AT NET OUT)

17870-A

FCC ID: F8I-DLCSMR2A User Manual - Part 4

Summary of content (9 pages)

PAGE 1
FCC ID: F8I-DLCSMR2A User Manual - Part 4 ADCP-75-159 • Issue 1 • August 2003 • Section 3: Host Unit Installation HOST UNIT 1 NET IN NET OUT HOST UNIT 2 NET IN NET OUT HOST UNIT 3 NET IN NET OUT 16900-B CONTROLLER AREA NETWORK INTERFACE CABLES TO NEXT HOST UNIT (NOTE: LAST HOST HAS NO CONNECTION AT NET OUT) Figure 3-10.
PAGE 2
ADCP-75-159 • Issue 1 • August 2003 • Section 3: Host Unit Installation 10 EXTERNAL ALARM SYSTEM CONNECTIONS The alarm interface between the HU and an external alarm system is supported by a six-terminal plug (with screw-type terminals) that connects to a receptacle mounted on the HU rear panel. The terminal plug provides connections to normally open (NO) and normally closed (NC) dry type alarm contacts for both major and minor alarms.
PAGE 3
ADCP-75-159 • Issue 1 • August 2003 • Section 3: Host Unit Installation 6. Connect the Major and Minor alarm wire pairs to the appropriate terminals on the external alarm system. 7. Dress and secure cable per standard industry practice. 11 DC POWER CONNECTIONS The HU is powered by ± 21 to ± 60 VDC power (nominal ± 24 or ± 48 VDC). The power is fed to the HU through a screw-down type terminal strip located on the rear side of the unit.
PAGE 4
ADCP-75-159 • Issue 1 • August 2003 • Section 3: Host Unit Installation 5. Remove the fuse from the circuit that will power the HU. 6. Connect the power wires to the appropriate terminals as specified in the fuse panel user manual. 7. Dress and secure the power wiring at the fuse panel and the HU. The procedure for checking the voltage level and verifying that the HU is ready to power up is provided in SECTION 4: OPERATION. Page 3-15 © 2003, ADC Telecommunications, Inc.
PAGE 5
ADCP-75-159 • Issue 1 • August 2003 • Section 3: Host Unit Installation Blank Page 3-16 © 2003, ADC Telecommunications, Inc.
PAGE 6
ADCP-75-159 • Issue 1 • August 2003 • Section 4: Operation SECTION 4: OPERATION Content 1 2 Page BEFORE STARTING OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1 1.1 Tools and Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1 1.2 Readiness Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 7
ADCP-75-159 • Issue 1 • August 2003 • Section 4: Operation 1.2 Readiness Check Before starting the turn-up process, inspect the complete Digivance system to verify that all components of the system are ready to be powered-up. This will ensure that no units of the system will be damaged during turn-up and that all existing systems will continue to function properly. 1.2.1 Host Unit Installation Checks Complete the following checks at the HU prior to starting the turn-up process: 1.
PAGE 8
ADCP-75-159 • Issue 1 • August 2003 • Section 4: Operation 2.1 Turn-Up Procedure Each Digivance system should be turned-up separately before being networked together with multiple systems through the CAN interface. Use the following procedure to turn-up each Digivance system: 1. Temporarily disconnect the external alarm system or notify the alarm system provider that testing is in progress. 2.
PAGE 9
ADCP-75-159 • Issue 1 • August 2003 • Section 4: Operation Click to view drop down menu Figure 4-1. Digivance Element Management System Main Window 9. Open the View drop down menu and connect to the Host and Remote pair by selecting “NotNamed/NotNamed”. The HOST Alarms display and the REMOTE Alarms display will open within the main window as shown in Figure 4-2. 10.