EN INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS FR NL ES Comfort E 100 - 130 - 160 - 210 - 240 IT DE PL RU 661Y1600 • C
EN TABLE OF CONTENTS GENERAL RECOMMENDATIONS................................................................4 FR USER'S GUIDE...............................................................................................5 Control Panel............................................................................................................................................................... 5 NL APPLIANCE DESCRIPTION..........................................................................
TABLE OF CONTENTS EN MAINTENANCE.........................................................................................23 FR Periodic Checks by the User.........................................................................................................................23 Annual Maintenance..........................................................................................................................................23 Draining...............................................................
EN GENERAL RECOMMENDATIONS NOTES FR NL • This manual contains important information with respect to the installation, the starting up and the maintenance of the hot water tank. • This manual must be provided to the user, who will read it carefully and keep it in a safe place. • The availability of certain models as well as their accessories may vary according to the markets.
USER'S GUIDE EN CONTROL PANEL 4 FR NL ES IT 1 2 3 Heating element ON Heating element OFF DE PL RU Key : 1. Control thermostat [60/90°C] - To set the domestic hot water (DHW) temperature. 2. Fuse FF 12,5 Amp - To provide an electric protection to the appliance. 3.
EN APPLIANCE DESCRIPTION MODELS - Comfort E 100 - 130 - 160 - 210 - 240 Storage water tanks, to be installed vertically on the wall, that can work within a heating installation, or independently as electric domestic hot water heater only. The Comfort E tank is equipped with one 2200 W heating element controlled by the thermostat and by the Summer/Winter switch on the appliance control panel. FR NL Key 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
APPLIANCE DESCRIPTION EN 3 FR 9 NL 4 7 ES 10 2 IT 6 DE 11 8 PL 12 5 RU 9 1 13 en 661Y1600 • C 7
EN TECHNICAL CHARACTERISTICS DIMENSIONS AND MAIN CHARACTERISTICS Comfort E FR Tank dimensions NL 100 130 160 210 240 A mm 845 1005 1205 1480 1725 B mm 365 525 725 1000 1245 C mm 630 790 990 1260 1510 Total capacity L 105 130 161 203 242 Primary circuit capacity L 30 55 62 77 78 Primary circuit connection [F] " 1 1 1 1 1/4 1 1/4 Main Characteristics ES IT DHW connection [M] " 3/4 3/4 3/4 3/4 3/4 Heating surface area m² 1.03 1.03 1.26 1.54 1.
TECHNICAL CHARACTERISTICS EN FR 530 NL B A ES IT 265 265 DE 325 563 PL 298 RU C 360 en 661Y1600 • C 9
EN TECHNICAL CHARACTERISTICS ELECTRICAL CHARACTERISTICS Comfort E Main characteristics FR Rated voltage V~ 100 230 130 230 160 230 210 230 240 230 Rated frequency Hz 50 50 50 50 50 W 2,200 2,200 2,200 2,200 2,200 A 10 10 10 10 10 Electrical consumption with electrical heating element Rated current with electrical heating element NL Wiring diagram ES 1. 2. 3. 4. 5. 6. 7. 8.
TECHNICAL CHARACTERISTICS EN PERFORMANCE Comfort E DHW performance 100 130 160 FR 210 240 Peak flow at 45 °C * L/10' 182 202 275 348 469 Peak flow at 45 °C * L/60' 604 672 911 1156 1560 Constant flow at 45 °C * L/h 507 564 763 970 1309 Power drawn * kW 23 23 31 39 53 Initial heating time ** Min. 9:10 9:10 8:50 8:50 8:50 2 h 43' 3 h 27' 4 h 20' 5 h 37' 6 h 37' 0.83 0.83 0.83 0.83 0.83 Heating time with the 2.
EN INSTALLATION SAFETY INSTRUCTIONS FR General remark NL • Connections (electrical, hydraulic) must be carried out in accordance with applicable standards and regulations. • If the water drawing off point is far from the tank, installing an auxiliary DHW loop can allow to get hot water more quickly at all times. Essential instructions for the correct operation of the installation ES IT • The tank must be installed in a dry and protected area.
INSTALLATION EN Essential instructions for the safety of persons and the environment • Hot water can burn! In the event of small amounts of hot water repeatedly being drawn off, a stratification effect can develop in the tank. The upper hot water layer may then reach very high temperatures. • ACV recommends using a pre-set thermostatic mixing valve in order to provide hot water at a maximum of 60°C. • Water heated to wash clothes, dishes and for other uses can cause serious burns.
EN INSTALLATION PACKING CONTENTS All appliances are delivered, tested and packaged separately. FR Package • • • NL One Comfort E hot water tank. One multilingual Installation, Operation and Maintenance Instructions. One wall-mounting kit with support and flow diverter General Remarks ES • The hot water tank must be installed on a wall using the provided wall-mounting kit. • The appliance should be positioned to allow the replacement of the sparge tube and dry well during servicing, if required.
INSTALLATION EN TANK POSITION FR NL ES IT DE PL RU en 661Y1600 • C 15
EN INSTALLATION CONNECTION Essential instructions for the safety of persons and the environment FR NL • Refer to the safety instructions for the installation. Failure to comply with these instructions can result in damages to the installation, severe injuries or death. • Hot water can burn! ACV recommends using a pre- set thermostatic mixing valve in order to provide hot water at a maximum of 60°C.
INSTALLATION EN CONNECTION TO THE PRIMARY CIRCUIT (Typ. vertical installation on a wall) FR Key 1. Primary circuit filling valve 2. Charging pump 3. Check valve 4. Primary circuit stop valve 5. Expansion vessel 6. Pressure gauge 7. Safety valve (set at 3 bar) 8. Drain valve 9.
EN INSTALLATION COMFORT E TANK USED AS ELECTRIC DHW TANK ONLY Do not power the heating element if the oustide tank is not filled and bled. FR 1. 2. 3. 4. 5. NL System filling valve Safety valve calibrated to 3 bar Expansion vessel Isolation valve, heating system Pressure gauge This connection to be plugged. ES 4 2 5 IT 3 1 DE AVAILABLE KITS AND ACCESSORIES PL DHW connection kit available (code: 10800102) A. DHW temperature control valve B. Mixed domestic hot water outlet C.
STARTING UP EN SAFETY INSTRUCTIONS TO FILL THE TANK Essential instructions for the safety of persons and the environment • The DHW tank must always be filled and pressurised before filling and pressurising the primary circuit. • Do not use vehicle antifreeze. This can cause serious injury or death, or damage facilities. • If antifreeze is needed in the primary circuit, it must comply with Public Hygiene Regulations and must be non-toxic. A food-grade Propylene Glycol is recommended.
EN STARTING UP FILLING Essential instructions for the correct operation of the installation FR • The DHW tank must always be filled and pressurised before filling and pressurising the primary circuit. FILLING THE DHW TANK (Figure 1) NL General remark • ES IT Connect the safety valve outlet to the sewer. 1. To fill the tank, open a hot water tap (2) located at the highest point of the installation. It enables to bleed the air from the installation. 2.
STARTING UP EN 2 FR NL ES 3 3 1 IT Figure 1 DE Cold water 4 Hot water 1 2 PL RU 1 2 3 Figure 2 en 661Y1600 • C 21
EN STARTING UP CHECKS BEFORE STARTING UP • Check that the safety valves (DHW and primary) are correctly installed and that the outlets are connected to the sewer. FR • Check that the DHW tank and the primary circuit are filled with water. • Check that the air has been correctly bled from both circuits. • Check that the tank’s upper air bleed valve is tight. NL • Check that the water side and heat source side pipes are correctly connected and not leaking.
MAINTENANCE EN PERIODIC CHECKS BY THE USER • Check the pressure of the primary circuit pressure gauge: it should be between 0.5 and 1.5 bar. FR • Visually inspect, on a regular basis, the valves, connections and accessories in order to detect any leaks or malfunction. • Periodically check the air bleed valve located on the tank top to ensure that it is not leaking. • Check that the DHW water circuit safety valves are in good operating condition.
EN MAINTENANCE DRAINING Essential instructions for the safety of persons and the environment FR • The water coming out of the drain valve is very hot and can cause very severe burns. Make sure the area around the hot water flow is clear of people. Essential instructions for the electrical safety • NL Shut down the external electrical supply of the installation before draining.
MAINTENANCE EN 3 FR 1 NL ES 1 2 IT Figure 3 Cold water DE Hot water 3 PL RU 1 4 2 Figure 4 en 661Y1600 • C 25
EN MAINTENANCE REPLACEMENT OF THE ELECTRIC HEATING ELEMENT FR • Switch off and disconnect the mains power supply to the appliance. • Be careful with the high temperature of the cylinder. • Drain the primary tank.
MAINTENANCE EN FAULT FINDING What to do if the domestic hot water is not heated anymore? 1 Check the power supply. 2 Check the proper operation of the boiler and the control thermostat of the tank. 3 Check if the load pump works properly and replace if necessary. 4 Check the fuse and replace if necessary. 5 Check the safety thermostat on the tank and reset if necessary. 6 Check the heating element and replace if necessary. FR NL ES IT 1. 2. 3. 4. 5. 6.
EN RATING PLATE FR KERKPLEIN N° 39 1601 RUISBROEK BELGIUM www.acv.com N E IM NL -------------------------------------Type : COMFORT E 160L N° Art. : 06602601 C E P N° Ser. : 99999 ES Year : 2014 S IT T. max. : : 90°C 230 V 50Hz Max. : 3 bar Max.
EN FR NL ES IT DE PL RU en 661Y1600 • C 29
EN FR NL ES IT DE PL RU en 30 661Y1600 • C
