2ADCB-REG127 Radio User Manual Version 1.
Acuity Brands Lighting, Inc. One Lithonia Way Conyers, GA 30012 Last edited: 12 March 2020 Copyright © 2019 Acuity Brands Lighting. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission from Acuity Brands Lighting.
2ADCB-REG127 Radio User Manual ROAM/Acuity Brands Version: [1.0] Revision Date [4/30/2019] Executive Sponsor Acuity Brands Lighting Signature Date Executive Sponsor [Name] [Email] Signature [Name] Date [Email] Signature [Name] Signature Page 3 of 27 [Telephone] [Telephone] Date [Email] [Telephone] Date © Acuity Brands Lighting 2020.
Table of Contents 1 EXECUTIVE SUMMARY ...................................................... ERROR! BOOKMARK NOT DEFINED. 2 GENERAL INFORMATION .................................................. ERROR! BOOKMARK NOT DEFINED. 2.1 COMPANY DETAILS ......................................................................... ERROR! BOOKMARK NOT DEFINED. 2.2 COMPANY(S) PROFILE ..................................................................... ERROR! BOOKMARK NOT DEFINED. 3 UNDERSTANDING OF REQUIREMENTS....
9.1 GLOSSARY OF TERMS ..................................................................... ERROR! BOOKMARK NOT DEFINED. Page 5 of 27 © Acuity Brands Lighting 2020.
Document History Paper copies are valid only on the day they are printed. Contact the author if you are in any doubt about the accuracy of this document. Revision History Revision Number Revision Date Summary of Changes Author Version 1.
1 Background The 2ADCB-REG127radio module is intended for installation in wirelessstreetlight controls applications. The module is supplied regulated 5.0 Vdc by amainboard with +/-1% regulated supply in all applications.The module contains voltage regulators and filtering capacitors onboard to smooth variations in supplyvoltage.It features a standard mini PCI-e edge connector and form-factor so it can be plugged in to any mini PCI-e USB only connector. Page 7 of 27 © Acuity Brands Lighting 2020.
2 Modem User’s Manual (not accessible to end-users). 2.1 Overview of the Radio Modem Hardware The 2ADCB-REG127 modem is an 802.15.4 wireless module that allows wireless communication using a standard asynchronous serial data stream. Themain features of the 2ADCB-REG127 radio modem are presented in the figures below. FCC ID label will be applied to the shield later.
2.2 Functional Block Diagram of the module NOTE: CONFIDENTIAL BLOCK DIAGRAM IS REMOVED The 2ADCB-REG127 radio module consists of four functional entities: Transceiver section – processor, RF Transceiver 2.) RF Section – BALUNs, RF Front-End, RF filters 3.) Non-volatile storage – EEPROM 4.) Voltage regulators – LDO 1.) 2.3 Pinout The module follows the mini PCI-e, USB only standard pinout. Page 9 of 27 © Acuity Brands Lighting 2020.
2.4 Operation of the 2ADCB-REG127 Radio Modem Communication with the ROAMMOD0001 radio modem happens through USB port. The baud rate is set to be 19200, 8N1. Document Name: Radio User Manual © 2020. All rights reserved.
2.5 Command Set Open an instance of terminal software on a serial port with the above settings and connect to the RF modem. Any command is single line followed by entercommand. Format of command is: command param1 param2 … Atstartup pushing the enter key a few times is necessary until the reception of theprompt string. PTS Commands description: 1. Clear screen a. Description: clear screen b. Command name: “cls” c. Parameters: None d. Ex: cls 2. Help a.
d. Ex: getreg 00 5. Set Modem SPI Register a. Description: set value for a modem register (from page0) b. Command name: “setreg” c. Parameters: 2 - register ID: hex format - register vlaue: hex format d. Ex: setreg 20 80FF 6. Set Power Amplification value a. Description: set value for a modem PA power (not persistent value) b. Command name: “setpa” c. Parameters: 1 - PA value: hex format d. Ex: setpa FC 7. Set Modem Channel a.
d. Ex: setredled 0 9. Set green LED value a. Description: set green LED on or off b. Command name: “setgreenled” c. Parameters: 1 - Green led: 0 or 1 d. Ex: setgreenled 0 10. Put modem in IDLE state a. Description: put modem in IDLE state b. Command name: “idle” c. Parameters: None d. Ex: idle 11. Put modem in PULSE state a. Description: put modem in pulse PRBS9 state b. Command name: “pulse” c. Parameters: None d. Ex: pulse 12. Put modem in RX state a.
- Msg signature: hex format, default value 0xFF d. Ex: rxecho 14. Calculate the TX message success rate a. Description: Calculate message success rate b. Command name: “txmsg” c. Parameters: 4 (but can missing) - Packet no: decimal format, default 100 - Delay (in ms): decimal format, default 100 - Packet len: decimal format, default 125 - Msg signature: hex format, default value 0xFF d. Ex: txmsg 10 15. Put modem in TX not modulated state a.
18. Clear EEPROM (except main info) a. Description: Clear EEPROM except main info b. Command name: “iic_erase” c. Parameters: None d. Ex: iic_erase 19. Write device SN on EEPROM a. Description: Set device SN on EEPROM and clear rest of EEPROM b. Command name: “iic_setsn” c. Parameters: 1 - Device SN: hex format, up to 16 digits (8 bytes) d. Ex: iic_setsn 4FC0 20. Write VRef on EEPROM a. Description: Set VRef on EEPROM b. Command name: “iic_setvref” c.
d. Ex: outlo A5 23. Set output pin in hi a. Description: Set a pin as output and in hi state b. Command name: “outhi” c. Parameters: 1 - Pin definition: string: port and bit d. Ex: outhi A5 Document Name: Radio User Manual © 2020. All rights reserved.
2.6 Frequency selection The 2ADCB-REG127 module is not frequency agile during run-time, but it can select an unoccupied portion of the spectrum at startup. The series uses a set of 16 channels as defined by the IEEE 802.15.4 standards which span a range from2405 to 2480 MHz with 5 MHz spacing between channels: The channel mask is the name used to describe the list of frequency channels that a radio can use.
2.7 RF Exposure Limit Warning To comply with FCC’s RF exposure limits for general population / uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. The above statement must be placed in the end-user’s operating manual of finished products. 2.
Le présentappareilestconforme aux CNR d’Industrie Canada applicablesauxappareils radio exempts de licence.L’exploitationestautorisée aux deuxconditions suivantes : (1) l’appareilnedoit pas produire de brouillage, et (2)l’utilisateur de l’appareildoit (2) accepter tout brouillage radio électriquesubi, mêmesi le brouillageestsusceptible d’encompromettre le fonctionnement. The above statement must be placed in the end-user’s operating manual of finished products. Page 19 of 27 © Acuity Brands Lighting 2020.
3 Installation This module is limited to OEM installation only • OEM Integrators may not provide instructions for end user to remove/install module. • This module is to be installed only in mobile or fixed applications -reference part 2.1091(b) for a definition of mobile and fixed devices. • Separate approval is required for all other operating configurations, including portable configurations with respect to 2.1093 and different antenna configurations. Document Name: Radio User Manual © 2020.
4 RF Exposure Limit Warning To comply with FCC’s RF exposure limits for general population / uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter (must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi transmitter product procedures).
5 Host Manufacturer Statements To ensure compliance with all non-transmitter functions the host manufacturer (ROAM/Acuity Brands Technical Services) is responsible for ensuring compliance with the module(s) installed and fully operational.
6 Import Statement The FCC regulates marketing, sale and importation of radio frequency devices. When importing a radio frequency (RF) device the importer or ultimate consignee, or their designated broker, may be required to declare that the radiofrequency device meets the FCC importation conditions under Title 47 of theCode of Federal Regulation (CFR) Section 2.1204. ROAM/Acuity BrandsTechnical Services marks the master carton of all devices containing 2ADCB-REG127 radios with the FCC ID and IC ID.
7 Module Labeling A certified module has the option to use a permanently affixed label, or an electronic label (see 9. Electronic Labelling below). For a permanently affixed label, the module must be labelled with an FCC ID - Section 2.926. See section 1 above for figures instructing installation of permanently affixed label. Label Size is 25 mm X 25 mm Document Name: Radio User Manual © 2020. All rights reserved.
8 Host Device Labeling For a host using a certified module with a standard fixed label, if (1) the module’s FCC ID is not visible when installed in the host, or (2) if the host is marketed so that end users do not have straightforward commonly used methods for access to remove the module so that the FCC ID and IC IDs of the module are visible; then an additional permanent label referring to the enclosed module: “Contains Transmitter Module FCC ID: 2ADCB-REG127 and IC: 6715C-REG127” or “Contains FCC ID: 2A
Document Name: Radio User Manual © 2020. All rights reserved.
Page 27 of 27 © Acuity Brands Lighting 2020.
