DTL – A Division of Acuity Brands Lighting Inc.
DTL – A Division of Acuity Brands Lighting Inc. DTL01/DTL02 User’s Manual Table of Contents Background ................................................................................................................................................... 3 Overview of Radio Module Hardware .......................................................................................................... 4 Theory of Operation................................................................................................
DTL – A Division of Acuity Brands Lighting Inc. DTL01/DTL02 User’s Manual Background The DTL01 radio module is intended for installation in Bluetooth streetlight controls applications and to communicate to keyfobDTL02. The module is supplied regulated 3.3Vdc by a DTL custom host board with +/-1% regulated supply in all applications. The keyfob is supplied by 3V coin cell CR2032.
DTL – A Division of Acuity Brands Lighting Inc. DTL01/DTL02 User’s Manual Overview of Radio Module Hardware The DTL01 and DTL02 are Bluetooth modules emitting GFSK 2.4GHz on the ISM band. The features are outlined below. FCC ID label will be applied as shown. Only the following antenna gain and type have been approved for use with these products: 2 dBi gain, PIFA antenna.
DTL – A Division of Acuity Brands Lighting Inc. DTL01/DTL02 User’s Manual 2dBi PIFA Antenna FCC ID: 2ADCB-DTL02 IC: 6715C-DTL02 Shield (FCC/IC label placed here) Theory of Operation THIS SECTION REMOVED TO KEEP CONFIDENTIALITY Operation of the DTL01 Radio Modem Communication with the DTL01 radio modem happens through UART 1. The baud rate is set to 115000, 8N1. Communications through P7 pin 8 (Tx) and pin 10 (Rx). Power through P1 pin 2 (GND) and pin 8 (Vcc).
DTL – A Division of Acuity Brands Lighting Inc. DTL01/DTL02 User’s Manual TX and RX Jumper required for JTAG programming and debug – unrelated to FCC testing VCC and GND Jumper required to enter production test mode Operation of the DTL02 Radio Modem Communication with the DTL02 radio modem happens through UART 1. The baud rate is set to 115000, 8N1. Communications through B4 (Tx) and B3 (Rx). Power is supplied through P1 pin 4 (Vcc) and pin 5 (Gnd).
DTL – A Division of Acuity Brands Lighting Inc. DTL01/DTL02 User’s Manual http://processors.wiki.ti.com/index.php/LPRF_BLE_HCITester Once the program can connect with the radio UART, the FCC tests that will need to be run are listed at: http://processors.wiki.ti.com/index.
DTL – A Division of Acuity Brands Lighting Inc. DTL01/DTL02 User’s Manual Where to change CW Mode or Channel Click once to view/change options or double click to execute. RF Exposure Limit Warning TBD FCC Certification Requirements This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
DTL – A Division of Acuity Brands Lighting Inc. DTL01/DTL02 User’s Manual Compliance Statement (Industry Canada) IC – CanadaThis device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may causeundesired operation of the device.
DTL – A Division of Acuity Brands Lighting Inc. DTL01/DTL02 User’s Manual Example Applications Picture of typical application of the DTL01 Module: The DCC127 series photocontrol will use this DTL01bluetooth board in order to communicate to the keyfobDTL02. The DCR remote key fob uses the DTL02bluetooth radio to communicate to the DCC127 series photocontrol. Installation The DTL01 module is limited to OEM installation only.
DTL – A Division of Acuity Brands Lighting Inc. DTL01/DTL02 User’s Manual Host Labeling The following are pictures and locations of the device labels.
