User Manual of 11ac Wave2 Tri-band AP This is the user manual of 11ac Wave2 Tri-band AP, which will approximate guide you how to set and apply the Ceiling AP, it provide a convenient graphical interface for network construction and maintenance person, as well as a user through a simple and accurate operation, and configuration management of the ceiling wireless access point.
RST: Reset Button, it make AP revert to default data after press it 15 seconds. WAN: Gigabit WAN Port, connect with ADSL modem or Internet mainly. It will be LAN port under Wireless AP and WiFi Repeater operation mode LAN: Gigabit LAN Port to end users LED: LED Indicator of WAN port and LAN port DC: DC power connector AP installation: Power Supply and working diagram: 1. Work at home: If work at home, this device can be power by DC adapter or PoE adapter. Then access into IP address 192.168.188.
P1 Working diagram 2. Work in business area: This wireless AP work in most business area like hotel, school, hospital, shopping wall etc. In this application, it work in FIT AP mode, powered by PoE switch, managed by AC controller in centrally or remotely.
P3 Working Diagram Connect Wireless AP with PC: Use can connect the PC with wireless AP by Wireless SSID and LAN cable: The diagram of wireless connection showed as follow: Pls note: the default SSID is WirelessAP2.4G/5.8G, SSID’s password is 66666666 P4.
2ndφLogin 1˅Connect the Ceiling AP with computer 2˅Configure the PC’s local connection IP address as 192.168.188.X (X is number from 2 to 254), subnet mask is 255.255.255.0, follow P4 and P5 to finish.
3) Input 192.168.188.253 into IE browser, then pop up the login page, the default login user name: Admin, Passwords: admin, pls do following P6 P7 Login 3rd : WEB GUI interface Setting: 1) Home After login, if default mode is FIT AP, then following device status will be showed: P8 home In fit AP, user can configure the IP mode, reset and reboot this device.
controller in centrally. Click FIT AP, then switch to FAT AP. For the FAT AP, the login page showed as follow: P7: Device Status FAT AP: Mean this AP in FAT mode now, click here to change to FIT AP if need. Pls note: FAT AP comply with SNMP protocol, can be configured through GUI interface or managed by SNMP controller. FIT AP comply with CAPWAP protocol, can be managed by CAPWAP controller.
P8 client list 2) Wizard In FAT AP ,support Gateway, Repeater, WISP and AP operation mode, which can be set in Wizard. Let’s show this operation mode one by one: P9 Wizard 2.
then click to continue. P10. WAN setting in Gateway Mode After configure the WAN setting, continue to Wi-Fi setting, including 2.4G Wi-Fi setting and 5G Wi-Fi setting: In this part, mainly to set the SSID, channel, password, security...
P11 Wireless Setting in Gateway Mode When click Next, then will complete the Gateway mode setting and show following picture, this AP will be reboot after click OK.
P12 Complete the setting in Gateway Mode When return to Status, the page showed as follow: P13 Status in Gateway Mode 2.2 WiFi Repeater mode Click WiFi Repeater operation mode in Wizard, then following page will pop up, scan the Wi-Fi and choose the SSID to be bridged, then next.
P14 Repeater Mode After click Next button, then should configure the wireless setting as follow, then click Next to set SSID, password, channel, for broadcast 2.
P15 Wireless Setting in Repeater Mode Click Return button, will back to Status, show Repeater mode data, show fail or success, and user can configure this data in this page if required.
2.3 WISP Operation mode: Click WISP operation mode in Wizard, then will pop up the configure page, pls set the WISP operation mode based on the step showed in picture: P17 WISP Mode Configure the right WAN setting in WISP operation mode, then next.
P18 WAN setting in WISP mode Configure wireless data showed as follow, including 2.
P19 Wireless Setting in WISP mode Then complete and back to status, will show the connection fail or success, then can configure the data based on request:
P20 Status in WISP mode 2.4 AP Operation mode: For the AP mode, mainly from cable internet to Wi-Fi internet. And for this AP, user can set fixed IP address for AP in LAN setting, or make AP obtain the IP address from gateway or AC controller. If obtain the IP address from gateway, mean IP address will be same segment of gateway; And if obtain IP address from AC controller, should set IP segment in the address server in AC controller part.
P21 LAN setting in AP Mode Click next in LAN setting, enter into wireless setting to set the SSID, password, channel, including 2.
P22 Wireless Setting in AP Mode P23 Status in AP Mode 3) WiFi
In WiFi setting, user can set SSID, channel, password, bandwidth for 2.4G wireless, 5.8G Wireless Let’s Click WiFi in home page, will show return home, will show 2.4G WiFi, 5G WiFi, MAC ACL, WiFi Timer off and Advance: For 2.4G WiFi, 5G WiFi, it is same configuration we showed in Wizard. P24 WiFi In the above picture, we can find WiFi Analyzer: Mainly to analyze the AP’s signal strength in some channel, then make AP work in the channel with small quantity of AP, to avoid WiFi interference.
Virtural AP: There are 3 virtual AP in 2.4G wireless, if need virtual SSID, then users can configure it showed in following picture: Click VAP1 in 2G WIFI--Enable WiFi status--input SSID, password--Click Apple to enable multi-SSID for 2.4G WiFi. P26 Virtual AP MAC ACL: Mean MAC access control: allow or deny user access by MAC address. P27 MAC Access Control WiFi Timer Off: mean WiFi SSID will be off in the configured time. Enable WiFi time off, set WiFi off time, then apply to finish.
P28 WiFi Timer Off Advanced Settings: In this page, will show the region, RF Power, Max user access... P29 Advanced Setting Country Region: can choose China, USA, Brazil, UAE, ETSI, India. 2G mode: including 11n/g (40MHz), 11b/g(20MHz) 5G mode: including 11a(20MHz), 11an(40MHz), 11ac(80MHz) Multicast Fast: Default is off, but can choose 6M,9M, 12M, 18M, 24M, 36M, 54M Maximum for per AP: mean maximum user for each band. WLAN Partition: mean user isolation, default is disable.
Short GI: data isolation, default is on. Coverage Threshold: The input data is signal strength that user connect with AP. The data is smaller, then mean user will connect with weak signal AP; the data is larger, mean user will connect to the stronger signal AP. Recommend to input -90dBm. TX Power: mean RF power is adjustable; Max mean the RF power showed in data sheet; Efficient: 4dBm lower than max; Enhanced: 4dBm lower than efficient... Preferred 5G: mean band steering, 5G priority.
P31 WiFi Timer Off VLAN setting: This AP support tag VLAN based on SSID. Input VLAN ID in 2G SSID, then when user access into this SSID, it get data from VLAN switch. Network--VLAN setting--ON- Input VLAN ID on SSID--Apply. P32 Tag VLAN Setting Cloud Server setting: In this part, make AP access into cloud server for remote management. But make sure: A.
already; B. Had registered ID from our cloud www.yowifi.net. P33 Cloud setting Management: In this part, show the device backup, reboot, password modify, firmware upgrade and log. P34 Management Backup: Mean if you do some configure for this AP, then can save this configuration in file to computer. Next time if reset the AP, then restore this backup file to restore this AP with same configuration before reset. Reset default: mean restore to factory default settings, all configuration will be missed.
Reboot: Reboot the device immediately, or reboot the device in certain time. Can reboot everyday or every week. P35 Reboot Modify password: Modify WEB GUI login password, the default is admin. P36 Modify password Upgrade firmware: Mean upgrade new firmware for this wireless AP, but before upgrade, pls note: A. the device can upgrade the firmware in newest version, can’t upgrade old version; B. don’t power off the device when upgrade the firmware; C. Reset the AP after firmware upgrade.
P37 Firmware Upgrade Time: Mean set system time for wireless AP. P38 Time Log:this is for AP working information, can export for problem recovery.
P39 System info 4th Share Internet and Obtain IP address automatically Set computer’s TPC/IP as Obtain an IP address automatically, Obtain DNS server address automatically as following picture showed. the computer will obtain the IP address from router or base station to get Internet. P40 Fix IP.
Failure phenomenon SYS Indicator off Can’t land to Wireless AP through Web page Wireless AP can’t connect with AP ˄the status display unconnected˅ Can’t scan the wireless AP The connection of Wireless AP and AP is success, but the computer can’t share internet How to Reset Wireless AP Solution Pls make sure the PoE module connection is right.
20c
