W725D0 802.11ABGN 2T2R USB Module Page 1 of 12 Product Specification Model Name: W725D0 Part No.: WW725D0566A20H IEEE 802.11ABGN 2T2R USB Module Version: 1.1 Date: June. 5.
W725D0 802.11ABGN 2T2R USB Module Page 2 of 12 Release History DATE REV Description of Change 2012/07/30 0.1 Preliminary specification release 2012/10/02 0.2 Add power consumption 2012/10/04 0.3 Update block diagram 2012/10/13 0.4 Update dimension and power consumption 2012/11/15 1.0 Change model name to W725D0, update RF Spec. 2013/5/7 1.0 Customized for Actiontec 2013/6/5 1.
W725D0 802.11ABGN 2T2R USB Module Page 3 of 12 W725D0 IEEE 802.11ABGN 2T2 USB Module 1 Product Features Supports 2T2R 2.4/5GHz dual-band Maximum PHY data rate up to 144.4 Mbps using 20MHz bandwidth, 300Mbps using 40MHz bandwidth Short Guard Interval (400ns) Sounding packet Host interface complies with USB Specification Revision 2.0 Supports IEEE 802.
W725D0 802.
W725D0 802.11ABGN 2T2R USB Module Page 5 of 12 3 General Specification Module Name W725D0 Product Specification WLAN Standard IEEE 802.11a/b/g/n USB 2.0 Host Interface Host Connector Options 4 pins header type connector Major Chipset Dimensions (board size) Realtek RTL8192DU Minimum Typical Maximum Unit Length 60.2 60.5 60.8 mm Width 22.4 22.6 22.8 mm Height 2.9 3.1 3.3 mm Weight 6.8 7 7.2 g Minimum Typical Maximum Unit 4.
W725D0 802.11ABGN 2T2R USB Module 802.11n/ HT40 Page 6 of 12 MCS7 -61 dBm 5GHz Band Output power Minimum Typical Maximum Unit 802.11a 54Mbps 8 10 12 dBm 802.11n/ HT20 MCS7 Lower/ Middle Band 7 9 11 dBm 802.11n/ HT20 MCS7 Upper Band 5 7 9 dBm 802.11n/ HT40 MCS7 Lower/ Middle Band 7 9 11 dBm 802.11n/ HT40 MCS7 Upper Band 5 7 9 dBm Minimum Typical Maximum Unit Receiver Sensitivit y 802.11a 54Mbps -65 dBm 802.11n/ HT20 MCS7 -64 dBm 802.
W725D0 802.11ABGN 2T2R USB Module Page 7 of 12 5 Power Consumption Test condition OS：Windows XP Channel 6：2437MHz Standard：IEEE802.11B,G.N Input voltage for whole circuit：4.97V TX uses continuous mode Test tool MP_Kit_RTL11n_DualMAC_9xD_USB_v019_20120307 5.1 Test result： Continuous TX/RX @ 2.
W725D0 802.11ABGN 2T2R USB Module Page 8 of 12 Test condition OS：Windows XP Channel 165：5825MHz Standard：IEEE802.11A, AN Input voltage for whole circuit：4.97V TX uses continuous mode 5.
W725D0 802.11ABGN 2T2R USB Module Page 9 of 12 Test condition OS：Windows XP Channel 6：2437MHz Standard：IEEE802.11G,N RF output connects with AP (D-Link DIR-635, 2T3R) Input voltage for whole circuit：4.97V Throughput test mode Distance Limit: 1M (Signal & Quality 100%) Test driver Realtek, RTL8192DU_Drv_1016.1.0413.2012_UI_1.00.0180.All_In_One_Driver_Merge d_UI.L 5.3 Test result：Throughput test @2.
W725D0 802.11ABGN 2T2R USB Module Page 10 of 12 Test condition OS：Windows XP Channel 165：5825MHz Standard：IEEE802.11A,N RF output connects with AP (D-Link DIR-635, 2T3R) Input voltage for whole circuit: 4.97V Throughput test mode Distance Limit: 1M (Signal & Quality 100%) Test driver Realtek, RTL8192DU_Drv_1016.1.0413.2012_UI_1.00.0180.All_In_One_Driver_Merge d_UI.L 8.
W725D0 802.11ABGN 2T2R USB Module 10.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence.
FOR MOBILE DEVICE USAGE Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé.
is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization.
Manuel d'information à l'utilisateur final L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiqué dans ce manuel.
