802MR User’s Manual
1. Wireless LAN Basics Wireless LAN (Local Area Networks) systems offer a great number of advantages over a traditional, wired system. Wireless LANs (WLANs) are more flexible, easier to setup and manage and often more cost effective than their wired equivalence. Using radio frequency (RF) technology. WLANs transmit and receive data over the air, minimizing the need for wired connections. Thus, WLANs combine data connectivity with user mobility, and, through simplified configuration, enable movable LANs.
2. Installation and Overview Here are some steps you will perform in establishing your wireless network connection: z z z Install Access Point at first. AP is needed in case of Infrastructure network mode. Install software using the Installation Disktette. Install network protocol(s) required to communicate on your network. Most likely you will need the TCP/IP protocol Here are some steps you will perform in installing your driver for AC97 Soft Modem.
3. Installation Procedure of 802.11b WLAN MiniPCI Card 1. 2. 3. Insert the card into MiniPCI Slot. Power on your computer and allow Windows to load fully. The Windows will detect your Mini-PCI card and show the following screen. Please click Next 4. Select Search for the best driver for your device. (Recommended).
. Insert the given Installation Diskette and select Specify a location to find out your driver location. Click Next to run setup. 6. Click Finished. The installation process are completely.
7. Click Yes to restart your computer. 8. Check for the 802.11b WLAN MiniPCI Card by right clicking on My Computer using the mouse. Select the Device manager and then Network Adapters. If you find the sign on the adapter, it shows the installation is not successful. If not, it means your setup is successfully. 3.1 Install network protocol(s) required to communicate on your network 9. Right click on the Network Neighborhood using the mouse.
10. Select Properties from the pop up menu. The network box appears and you see the three main tables: Configuration, Identification and Access control. 11. Click on the Configuration tab and then click on the Add button. Select Network component Type Box appears.
12. Select Network Protocols box appears. From the list of manufactures, Click on Microsoft. From the list of network protocols list, select NetBEUI, then click OK 13. The NetBEUI protocol is now installed. After clicking on OK return back to Network Component Type box. 14. Repeat the Step 10 and 11 to add IPX/SPX protocol. 15. Repeat the step 10 and 11 to add TCP/IP protocol.
16. Click on TCP/IP option for setting the IP address for your computer. You can select either Static or DHCP setting. If you use the static IP setup then enter the IP value, Subnet masking, DNS, Domain/Workgroup name, and Gateway address values. After setting these parameter appropriately, click OK to return to Network component type. 17.
4. Installation Procedure of 56K Mini-PCI Fax Modem Card 1. Start Windows 2. Windows will immediately display the New Hardware Wizard and identify the modem. Click the Next button. 3.
4. Please choose Specify a location & insert the installation disk into Floppy or CD-ROM.
5. After the drivers are installed, click “Finish” After Windows re-starts, you can check your modem by following instructions to checking your 802MR if setup successfully. 6. Go to My Computer Control Panel The Modem Properties screen will be displayed. 7.
7. The Modem will respond to the following message as screen showed that means your modem installed successfully.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.