CUSTOM VEHICLE HEADRESTS with 7” or 8” Slim Style LED LCD Monitors with Built-in DVD Player for Rear Seat Entertainment With FM Transmitter FM Transmtter 8” Slim Style LED LCD Monitor 7” Slim Style LED LCD Monitor Installation Guide
IMPORTANT NOTICE Installation of headrest products require careful planning and preparation. Be extremely careful of seats that have airbags built into them. Keep wiring away from any airbag wiring (usually identified by yellow connectors and yellow wire jackets). Damage to airbag wiring can result in personal injury to vehicle occupants. If you have any questions regarding wire routing or installation in a vehicle, please contact VOXX Technical Support at 1-800-225-6074.
MATERIALS INCLUDED IN THIS PACKAGE: Installation Package (P/N XXXX) (1pc) b) 2 Pin DC Power Cable (P/N 112-3667) - (1pc) a) Wireless FM Interface Box (P/N 136-XXXX) - (1pc) - or (P/N 112-4327) - (1pc) c) HDMI Cable (P/N 112-XXXX) - (1pc) d) Installation Guide The wireless FM Interface Box automatically determines which headrest is M1 and which headrest is M2 and sets each headrest to its own function (IR transmitter channel and IR receiver remote control codes).
VEHICLE PREPARATION: 1) Read the installation guide and get familiar with the electrical requirements and connections. 2) Prepare the vehicle by removing any interior trim necessary to gain access to the vehicle’s wiring as well as all areas where interconnecting wire harnesses will be located. a) Monitors: Vehicle-specific Headrest NOTE: - The M1 monitor has the pink/green connectors. - The M2 monitor has the blue/yellow connectors.
VEHICLE PREPARATION (continued): 6) Connect all the components together (electrically) and verify proper operation of all the system functions. (Refer to the Headrest System Wiring Diagram on page 6) a) Connect the headrest DIN cables to the FMM Interface Box DIN cables which are color coded. Connect each headrest cable to the correct color cable on the Wireless FMM Interface Box.
HEADREST SYSTEM WIRING DIAGRAM Master Monitor 112-4289 HRM2 GREEN 112-4288 HRM1 PINK Satellite Monitor 112-4290 HRS1 YELLOW 112-4291 HRS2 BLUE HDMI &USB CABLE FM ANTENNA FM INTERFACE BOX AV Output DC IN ** 2 PIN DC POWER CABLE OPTIONAL FM DIRECT CONNECTION OPTIONAL MVGP1 (GAME PACKAGE) MVGP1 FMDIRB GAME MODULE * Relay Box for wireless FM Modulator See the instructions supplied with the FMDIRB for installation.
” ELECTRONICS INSTALLATION/REPLACEMENT GUIDE Install Monitor Unit To Headrest Installation NOTE: Switch off the ACC power during cable and unit installation. Failure to do so may damage the unit.
7” ELECTRONICS INSTALLATION/REPLACEMENT GUIDE (continued) 6 5 Reverse the procedure for removing the electronics.
8” ELECTRONICS INSTALLATION/REPLACEMENT GUIDE Install Monitor Unit To Headrest Installation NOTE: Switch off the ACC power during cable and unit installation. Failure to do so may damage the unit.
8” ELECTRONICS INSTALLATION/REPLACEMENT GUIDE (continued) 6 5 Reverse the procedure for removing the electronics.
OPTIONAL: he MVGP1 Game Package is the optional accessory package that allows adding T a wireless game source feature.
TROUBLESHOOTING GUIDE AUDIO RELATED ISSUES No audio on wireless headphones while playing a DVD 1. Check that the batteries in wireless headphones are good and that they are installed properly. 2. Check that the headphones are set to the proper channel: Channel A (1) for the M1 monitor, Channel B (2) for the M2 monitor. 3. Check that the monitor is not in MUTE mode. 4. Check that the IR transmitter is set to ON. No audio from Wireless FM modulator 1.
TROUBLESHOOTING GUIDE (CONTINUED) No audio on the M2 monitor when playing a DVD on the M1 monitor. 1. Check to see if there is audio on the RCA output connectors of the FMM interface box (the FM modulator uses the same audio for the AV output of the FMM Interface Box). 2. If there is audio on the FM Modulator or the RCA output connectors, check the YELLOW DIN cable for proper connections (audio to and from the M2 monitor travels on the YELLOW DIN cable). 3.
TROUBLESHOOTING GUIDE (CONTINUED) IR Remote Control Remote control does not work on either monitor. 1. Check that the battery is good. 2. Check that the battery is installed properly. 3. To control the M1 monitor, make sure M1 is pressed and the DVD button is pressed for DVD controls. For system controls, press the M1 button and the TV button. 4. Test the remote control with a cell phone. Turn on the cell phone camera.
TROUBLESHOOTING GUIDE (CONTINUED) M1 DIN cables and M2 DIN cables can be swapped for troubleshooting: Plug the M2 - Blue connector to M1 - Green connector on the box Plug the M2 - Yellow connector to M1 - Pink connector on the box Plug the M1 - Green connector to M2 - Blue connector on the box Plug the M2 - Pink connector to M2 - Yellow connector on the box This changes the M1 monitor to the M2 monitor and the M2 monitor to the M1 monitor.
FCC Note This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.